AS2Sender Component

Properties   Methods   Events   Config Settings   Errors  

The AS2Sender component implements an AS2 / EDI-INT client.

Syntax

nsoftware.IPWorksEDI.As2sender

Remarks

The AS2Sender component may be used to send EDI or other messages over HTTP/S, using the AS2 protocol. It may also be used to verify synchronous or asynchronous server responses.

A typical AS2 transaction is as follows:

(1) The sender sends an EDI document to the receiver using HTTP or HTTPS. Typically the document will be signed and encrypted (particularly if SSL is not used). A signed receipt will also be requested.

(2) The receiver decrypts the message and verifies the signature.

(3) The receiver sends a signed receipt back to the client. The signature is over the hash of an MDN, which contains a hash of the received message.

When sending an EDI message, the client should specify, at a minimum, AS2From and AS2To, URL, and EDIData. The Post method should then be invoked.

To secure the EDI transmission, the message may be signed and/or encrypted by setting the appropriate certificates. By default, the component will apply message security if the appropriate certificates are specified. To sign the data, set SigningCert. To encrypt, set RecipientCerts. If the recipient uses different certificates for signing and encryption it will also be necessary to set ReceiptSignerCert.

SSL will also be used if the scheme in URL is "https". If your trading partner is using a self-signed certificate, it will be necessary to set SSLAcceptServerCert or trap the SSLServerAuthentication event to accept the certificate.

The message may also be compressed by setting CompressionFormat.

To request a receipt, or Message Disposition Notification (MDN), simply set the MDNTo property. The MDNOptions property may be used to customize the request. By default, the component will request a signed MDN over an SHA1 hash.

The component supports both synchronous and asynchronous MDN receipt delivery. By default, the component requests synchronous MDN receipt delivery, and the MDN will be returned in the HTTP reply. To request asynchronous MDN delivery, set the MDNDeliveryOption to the URL where MDN's are to be delivered.

The HTTP reply will automatically be processed by the component. If an MDN was requested, Post will validate the MDN and (if signed) establish non-repudiation of receipt. Any errors or warnings will cause the component to throw an exception.

In either case, after the EDI transaction is processed successfully, the MDNReceipt will be populated with the appropriate values.

Validating Asynchronous MDNs

The component may also be used to process and verify asynchronous MDNs. To do this, you should invoke ReadAsyncReceipt. This will read the receipt from the current HTTP context (or from MDNReceipt, if set manually), and allow you to determine your trading partner's identity and the message ID. You should then set ReceiptSignerCert and OriginalContentMIC, and finally invoke VerifyReceipt.

Property List


The following is the full list of the properties of the component with short descriptions. Click on the links for further details.

AS2FromThe AS2 Identifier of the sending system.
AS2ToThe AS2 Identifier of the receiving system.
AS2VersionThe version of AS2 being used.
AsyncMDNInfoDirPath to a directory to store data used in verifying AsyncMDNs.
AttachmentsCollection of files attached to the current message.
CEMDetailsA collection of Certificate Exchange Messaging (CEM) details.
CompressionFormatThe compression format (if any) to use.
CookiesThis property includes a collection of cookies.
EDIDataThe EDI or other data to be sent.
EncryptionAlgorithmThe algorithm used to encrypt the EDI data.
EtagThe Etag of the file being sent.
FirewallA set of properties related to firewall access.
FromThe email address of the HTTP agent (optional).
LocalHostThe name of the local host or user-assigned IP interface through which connections are initiated or accepted.
LogDirectoryThe path to a directory for logging.
LogFileThe log file written.
MDNDeliveryOptionA URL indicating how the receipt is to be delivered.
MDNOptionsUsed to indicate the options requested for the MDN receipt.
MDNReceiptThe MDN receipt returned from the server.
MDNToUsed to indicate that a message disposition notification is requested.
MessageIdThe Id of the message.
OriginalContentMICThe Message Integrity Check(s) (one-way hash) of the outgoing message.
ProxyA set of properties related to proxy access.
ReceiptSignerCertThe public key certificate for the MDN receipt signature.
RecipientCertsThe public key certificates of the recipients for this message.
RestartDirectoryThe directory to log cached files when using AS2 restart functionality.
RolloverSigningCertContains the certificate to use when signing messages.
SignatureAlgorithmSignature algorithm to be used in outgoing messages.
SigningCertContains the certificate to use when signing messages.
SSLAcceptServerCertInstructs the component to unconditionally accept the server certificate that matches the supplied certificate.
SSLCertThe certificate to be used during SSL negotiation.
SSLProviderThis specifies the SSL/TLS implementation to use.
SSLServerCertThe server certificate for the last established connection.
SubjectThe subject of the message.
TimeoutA timeout for the component.
URLThe URL to which the request is made.
UseOAEPThis property specifies whether or not to use Optimal Asymmetric Encryption Padding (OAEP).
UsePSSThis property specifies whether or not RSA-PSS will be used during signing and verification.
UserAgentInformation about the user agent.

Method List


The following is the full list of the methods of the component with short descriptions. Click on the links for further details.

ConfigSets or retrieves a configuration setting.
DoEventsProcesses events from the internal message queue.
InterruptInterrupt the current method.
PostPost data to the AS2 server, and check the receipt.
ReadAsyncReceiptReads an asynchronous MDN receipt from the current HTTP session.
ResetResets the state of the control.
RestartRestart sending of the file specified by the Etag property.
SendCEMRequestSends a Certificate Exchange Messaging (CEM) request.
SendCEMResponseSends a Certificate Exchange Messaging (CEM) response.
SetRequestHeaderAllows the user to set or add arbitrary HTTP request headers.
SetTPInfoA convenient way to set AS2 communication parameters using XML strings.
VerifyReceiptVerifies an asynchronous MDN receipt.

Event List


The following is the full list of the events fired by the component with short descriptions. Click on the links for further details.

ConnectedThis event is fired immediately after a connection completes (or fails).
DisconnectedThis event is fired when a connection is closed.
EndTransferThis event is fired when a document finishes transferring.
ErrorFired when information is available about errors during data delivery.
HeaderThis event is fired every time a header line comes in.
LogFired with log information while processing a message.
SetCookieThis event is fired for every cookie set by the server.
SignerCertInfoThis event is fired during verification of the signed message.
SSLServerAuthenticationFired after the server presents its certificate to the client.
SSLStatusFired when secure connection progress messages are available.
StartTransferThis event is fired when a document starts transferring (after the headers).
TransferThis event is fired while a document transfers (delivers document).

Config Settings


The following is a list of config settings for the component with short descriptions. Click on the links for further details.

AllowMDNWarningsWhether to fail on MDN warnings.
AuthorizationThe Authorization string to be sent to the server.
AuthSchemeThe authorization scheme to be used when server authorization is to be performed.
CompressFirstWhether compression occurs before signing a message.
EncodeToTempDirWhether to use temporary files when creating messages.
IgnoreLoggingErrorsWhether to ignore errors that occur when writing to the log.
IncludeHeadersWhether headers are included when posting to a file.
LogDebugWhether to log debug data.
LogFilenameThe base name of the log file.
LogOptionsThe information to be written to log files.
MDNDispositionReturns the Disposition header of the MDN.
MessageHeadersReturns the headers of the message.
NormalizeMICWhether to normalize line endings before calculating the MIC.
OAEPMGF1HashAlgorithmThe MGF1 hash algorithm used when encrypting a key.
OAEPParamsThe hex encoded OAEP parameters to be used when encrypting a key.
OAEPRSAHashAlgorithmThe RSA hash algorithm used when encrypting a key.
PasswordA password if authentication is to be used.
PostToFileCreates the message on disk.
RequiredSignatureAlgorithmsSpecifies a list of acceptable signature algorithms.
UserA user name if authentication is to be used.
AcceptEncodingUsed to tell the server which types of content encodings the client supports.
AllowHTTPCompressionThis property enables HTTP compression for receiving data.
AllowHTTPFallbackWhether HTTP/2 connections are permitted to fallback to HTTP/1.1.
AllowNTLMFallbackWhether to allow fallback from Negotiate to NTLM when authenticating.
AppendWhether to append data to LocalFile.
AuthorizationThe Authorization string to be sent to the server.
BytesTransferredContains the number of bytes transferred in the response data.
ChunkSizeSpecifies the chunk size in bytes when using chunked encoding.
CompressHTTPRequestSet to true to compress the body of a PUT or POST request.
EncodeURLIf set to True the URL will be encoded by the component.
FollowRedirectsDetermines what happens when the server issues a redirect.
GetOn302RedirectIf set to True the component will perform a GET on the new location.
HTTP2HeadersWithoutIndexingHTTP2 headers that should not update the dynamic header table with incremental indexing.
HTTPVersionThe version of HTTP used by the component.
IfModifiedSinceA date determining the maximum age of the desired document.
KeepAliveDetermines whether the HTTP connection is closed after completion of the request.
KerberosSPNThe Service Principal Name for the Kerberos Domain Controller.
LogLevelThe level of detail that is logged.
MaxHeadersInstructs component to save the amount of headers specified that are returned by the server after a Header event has been fired.
MaxHTTPCookiesInstructs component to save the amount of cookies specified that are returned by the server when a SetCookie event is fired.
MaxRedirectAttemptsLimits the number of redirects that are followed in a request.
NegotiatedHTTPVersionThe negotiated HTTP version.
OtherHeadersOther headers as determined by the user (optional).
ProxyAuthorizationThe authorization string to be sent to the proxy server.
ProxyAuthSchemeThe authorization scheme to be used for the proxy.
ProxyPasswordA password if authentication is to be used for the proxy.
ProxyPortPort for the proxy server (default 80).
ProxyServerName or IP address of a proxy server (optional).
ProxyUserA user name if authentication is to be used for the proxy.
SentHeadersThe full set of headers as sent by the client.
StatusCodeThe status code of the last response from the server.
StatusLineThe first line of the last response from the server.
TransferredDataThe contents of the last response from the server.
TransferredDataLimitThe maximum number of incoming bytes to be stored by the component.
TransferredHeadersThe full set of headers as received from the server.
TransferredRequestThe full request as sent by the client.
UseChunkedEncodingEnables or Disables HTTP chunked encoding for transfers.
UseIDNsWhether to encode hostnames to internationalized domain names.
UsePlatformDeflateWhether to use the platform implementation to decompress compressed responses.
UsePlatformHTTPClientWhether or not to use the platform HTTP client.
UseProxyAutoConfigURLWhether to use a Proxy auto-config file when attempting a connection.
UserAgentInformation about the user agent (browser).
CloseStreamAfterTransferIf true, the component will close the upload or download stream after the transfer.
ConnectionTimeoutSets a separate timeout value for establishing a connection.
FirewallAutoDetectTells the component whether or not to automatically detect and use firewall system settings, if available.
FirewallHostName or IP address of firewall (optional).
FirewallListenerIf true, the component binds to a SOCKS firewall as a server (TCPClient only).
FirewallPasswordPassword to be used if authentication is to be used when connecting through the firewall.
FirewallPortThe TCP port for the FirewallHost;.
FirewallTypeDetermines the type of firewall to connect through.
FirewallUserA user name if authentication is to be used connecting through a firewall.
KeepAliveIntervalThe retry interval, in milliseconds, to be used when a TCP keep-alive packet is sent and no response is received.
KeepAliveTimeThe inactivity time in milliseconds before a TCP keep-alive packet is sent.
LingerWhen set to True, connections are terminated gracefully.
LingerTimeTime in seconds to have the connection linger.
LocalHostThe name of the local host through which connections are initiated or accepted.
LocalPortThe port in the local host where the component binds.
MaxLineLengthThe maximum amount of data to accumulate when no EOL is found.
MaxTransferRateThe transfer rate limit in bytes per second.
ProxyExceptionsListA semicolon separated list of hosts and IPs to bypass when using a proxy.
TCPKeepAliveDetermines whether or not the keep alive socket option is enabled.
TcpNoDelayWhether or not to delay when sending packets.
UseIPv6Whether to use IPv6.
UseNTLMv2Whether to use NTLM V2.
CACertFilePathsThe paths to CA certificate files when using Mono on Unix/Linux.
LogSSLPacketsControls whether SSL packets are logged when using the internal security API.
ReuseSSLSessionDetermines if the SSL session is reused.
SSLCACertsA newline separated list of CA certificate to use during SSL client authentication.
SSLCheckCRLWhether to check the Certificate Revocation List for the server certificate.
SSLCheckOCSPWhether to use OCSP to check the status of the server certificate.
SSLCipherStrengthThe minimum cipher strength used for bulk encryption.
SSLEnabledCipherSuitesThe cipher suite to be used in an SSL negotiation.
SSLEnabledProtocolsUsed to enable/disable the supported security protocols.
SSLEnableRenegotiationWhether the renegotiation_info SSL extension is supported.
SSLIncludeCertChainWhether the entire certificate chain is included in the SSLServerAuthentication event.
SSLKeyLogFileThe location of a file where per-session secrets are written for debugging purposes.
SSLNegotiatedCipherReturns the negotiated cipher suite.
SSLNegotiatedCipherStrengthReturns the negotiated cipher suite strength.
SSLNegotiatedCipherSuiteReturns the negotiated cipher suite.
SSLNegotiatedKeyExchangeReturns the negotiated key exchange algorithm.
SSLNegotiatedKeyExchangeStrengthReturns the negotiated key exchange algorithm strength.
SSLNegotiatedVersionReturns the negotiated protocol version.
SSLSecurityFlagsFlags that control certificate verification.
SSLServerCACertsA newline separated list of CA certificate to use during SSL server certificate validation.
TLS12SignatureAlgorithmsDefines the allowed TLS 1.2 signature algorithms when SSLProvider is set to Internal.
TLS12SupportedGroupsThe supported groups for ECC.
TLS13KeyShareGroupsThe groups for which to pregenerate key shares.
TLS13SignatureAlgorithmsThe allowed certificate signature algorithms.
TLS13SupportedGroupsThe supported groups for (EC)DHE key exchange.
AbsoluteTimeoutDetermines whether timeouts are inactivity timeouts or absolute timeouts.
FirewallDataUsed to send extra data to the firewall.
InBufferSizeThe size in bytes of the incoming queue of the socket.
OutBufferSizeThe size in bytes of the outgoing queue of the socket.
BuildInfoInformation about the product's build.
GUIAvailableWhether or not a message loop is available for processing events.
LicenseInfoInformation about the current license.
MaskSensitiveWhether sensitive data is masked in log messages.
UseFIPSCompliantAPITells the component whether or not to use FIPS certified APIs.
UseInternalSecurityAPIWhether or not to use the system security libraries or an internal implementation.

AS2From Property (AS2Sender Component)

The AS2 Identifier of the sending system.

Syntax

public string AS2From { get; set; }
Public Property AS2From As String

Default Value

""

Remarks

May be company name, DUNS number, or anything agreed on by trading partners.

Required.

AS2To Property (AS2Sender Component)

The AS2 Identifier of the receiving system.

Syntax

public string AS2To { get; set; }
Public Property AS2To As String

Default Value

""

Remarks

May be company name, DUNS number, or anything agreed on by trading partners.

Required.

AS2Version Property (AS2Sender Component)

The version of AS2 being used.

Syntax

public string AS2Version { get; }
Public ReadOnly Property AS2Version As String

Default Value

"1.2"

Remarks

The version of AS2 being used.

This property is read-only.

AsyncMDNInfoDir Property (AS2Sender Component)

Path to a directory to store data used in verifying AsyncMDNs.

Syntax

public string AsyncMDNInfoDir { get; set; }
Public Property AsyncMDNInfoDir As String

Default Value

""

Remarks

If Post is invoked after setting AsyncMDNInfoDir and an asynchronous MDN is requested, the component stores the data required to verify AsyncMDNs in a file in the specified directory. The name of the file is the MessageId of the outgoing message.

AsyncMDNInfoDir is also used while verifying asynchronous MDNs using VerifyReceipt. The properties required to process AsyncMDNs, namely OriginalContentMIC and MDNOptions, are automatically read from the file saved at the time of sending the original message.

Attachments Property (AS2Sender Component)

Collection of files attached to the current message.

Syntax

public EDIAttachmentList Attachments { get; }
Public Property Attachments As EDIAttachmentList

Remarks

When a call to Send is made, the component will attach the files referenced by each EDIAttachment in this collection to the EDIData.

This property is not available at design time.

Please refer to the EDIAttachment type for a complete list of fields.

CEMDetails Property (AS2Sender Component)

A collection of Certificate Exchange Messaging (CEM) details.

Syntax

public CEMDetailList CEMDetails { get; }
Public Property CEMDetails As CEMDetailList

Remarks

This collection holds Certificate Exchange Messaging (CEM) details. The details define the certificate, respond-by-date, and more.

When using AS2Sender see SendCEMResponse and SendCEMRequest for more information.

When using AS2Receiver see CEMRequest and CEMResponse for more information.

This property is not available at design time.

Please refer to the CEMDetail type for a complete list of fields.

CompressionFormat Property (AS2Sender Component)

The compression format (if any) to use.

Syntax

public As2senderCompressionFormats CompressionFormat { get; set; }

enum As2senderCompressionFormats { cfNone, cfZLIB }
Public Property CompressionFormat As As2senderCompressionFormats

Enum As2senderCompressionFormats cfNone cfZLIB End Enum

Default Value

0

Remarks

By default, outgoing data will not be compressed. Setting this property will instruct the component to compress the outgoing data using the indicated format.

Compression is highly recommended for large messages, as it will reduce network bandwidth and processing time required.

The compression algorithm used is Zlib, as required by RFC 3274 and defined in RFCs 1950 and 1951.

Cookies Property (AS2Sender Component)

This property includes a collection of cookies.

Syntax

public HTTPCookieList Cookies { get; }
Public Property Cookies As HTTPCookieList

Remarks

This property contains a collection of cookies. To add cookies to outgoing HTTP requests, add cookies (of type HTTPCookie) to this collection.

To see cookies that are set by the server, use the SetCookie event, which displays the cookies and their properties as set by the server. Those cookies also are added to Cookies.

MaxHTTPCookies can be used to control the maximum number of cookies saved.

This collection is indexed from 0 to count -1.

This property is not available at design time.

Please refer to the HTTPCookie type for a complete list of fields.

EDIData Property (AS2Sender Component)

The EDI or other data to be sent.

Syntax

public EDIData EDIData { get; set; }
Public Property EDIData As EDIData

Remarks

The EDI message to send.

This property is not available at design time.

Please refer to the EDIData type for a complete list of fields.

EncryptionAlgorithm Property (AS2Sender Component)

The algorithm used to encrypt the EDI data.

Syntax

public string EncryptionAlgorithm { get; set; }
Public Property EncryptionAlgorithm As String

Default Value

"3DES"

Remarks

If RecipientCerts contains a valid certificate, the data will be encrypted using this certificate and the algorithm specified in EncryptionAlgorithm. If EncryptionAlgorithm is set to the empty string, the data will not be encrypted.

The component supports "3DES", or industry-standard 168-bit Triple-DES encryption.

The component supports "AES" encryption with a default keysize of 128 bits. You may also set "AESCBC192" or "AESCBC256" for 192- and 256-bit keysizes.

Possible values are:

  • 3DES (default)
  • DES
  • AESCBC128
  • AESCBC192
  • AESCBC256
  • AESGCM128
  • AESGCM192
  • AESGCM256

Etag Property (AS2Sender Component)

The Etag of the file being sent.

Syntax

public string Etag { get; set; }
Public Property Etag As String

Default Value

""

Remarks

This specifies the Etag for the file. This value should be set to an empty string the first time a file is sent using the Restart command. The component will generate a unique Etag based on the processed contents of the file and set this property when sending begins.

If a file is interrupted, this value must be set when Restart is called to resume transfer of the already processed file.

Firewall Property (AS2Sender Component)

A set of properties related to firewall access.

Syntax

public Firewall Firewall { get; set; }
Public Property Firewall As Firewall

Remarks

This is a Firewall-type property, which contains fields describing the firewall through which the component will attempt to connect.

Please refer to the Firewall type for a complete list of fields.

From Property (AS2Sender Component)

The email address of the HTTP agent (optional).

Syntax

public string From { get; set; }
Public Property From As String

Default Value

""

Remarks

If the From property contains a non-empty string, an HTTP From: header is added to the request. This header generally gives the email address of the requester of the document.

This property is not available at design time.

LocalHost Property (AS2Sender Component)

The name of the local host or user-assigned IP interface through which connections are initiated or accepted.

Syntax

public string LocalHost { get; set; }
Public Property LocalHost As String

Default Value

""

Remarks

The LocalHost property contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multi-homed hosts (machines with more than one IP interface) setting LocalHost to the value of an interface will make the component initiate connections (or accept in the case of server components) only through that interface.

If the component is connected, the LocalHost property shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multi-homed hosts (machines with more than one IP interface).

NOTE: LocalHost is not persistent. You must always set it in code, and never in the property window.

The LocalHost property contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multi-homed hosts (machines with more than one IP interface) setting LocalHost to the value of an interface will make the component initiate connections (or accept in the case of server components) only through that interface.

If the component is connected, the LocalHost property shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multi-homed hosts (machines with more than one IP interface).

NOTE: LocalHost is not persistent. You must always set it in code, and never in the property window.

LogDirectory Property (AS2Sender Component)

The path to a directory for logging.

Syntax

public string LogDirectory { get; set; }
Public Property LogDirectory As String

Default Value

""

Remarks

Setting LogDirectory will instruct the component to log the details of each transmission to unique files in the specified directory. For each request processed, the component will log the complete text of the outgoing request and the incoming response.

The component will write multiple log file for each transmission, with separate extensions for each type of data:

Status (.log)Contains information on applied security options and pass/fail status of transmission
Request (.req)Contains the outgoing request, after security options have been applied
Payload (.dat)Contains log of unsecured payload prior to transmission
MDN Receipt (.mdn)For synchronous requests or asynchronous receipts verified with VerifyReceipt, contains MDN receipt.
Error (.err)This is only written in an error is encountered, containing the error.

One or more of these logs may be disabled by setting the LogOptions configuration setting.

LogDirectory supports several macros that can be used to specify a unique directory path. If the path specified does not already exist, the component will attempt to create the directory. The following macros are supported:

%MessageID%The MessageID of the AS2 transmission, after it is generated.
%AS2From%The AS2-From field in the transmission
%OriginalMessageID%In MDN Receipts, the MessageID of the transmission that the receipt is for. You can use this to pair asynchronous MDN receipt logs with their transmissions
%date:format%%Format% is a platform-specific date/time formatting string. For example: yyyy-MM-dd-HH-mm-ss-tttt

The filenames will be chosen automatically by the component. Each filename will be the system time, in the format YYYY-MM-DD-HH-MM-SS-MMMM, with extensions "-2", "-3", used in case files of those names already exist. After each transaction is processed LogFile will contain the name of the files just written, minus the extension.

If logs cannot be written an exception will be thrown.

LogFile Property (AS2Sender Component)

The log file written.

Syntax

public string LogFile { get; }
Public ReadOnly Property LogFile As String

Default Value

""

Remarks

If LogDirectory is specified a log file will be written in the specified directory and LogFile will contain the full path and name of the files written, minus the extension.

The component will write multiple log files for each transmission, with separate extensions for each type of data:

Status (.log)Contains information on applied security options and pass/fail status of transmission
Request (.req)Contains the outgoing request, after security options have been applied
Payload (.dat)Contains the unsecured payload data prior to transmission
MDN Receipt (.mdn)For synchronous requests or asynchronous receipts verified with VerifyReceipt. This contains the MDN receipt.
Error (.err)This is only written if an error is encountered and will contain the error.

This property is read-only.

MDNDeliveryOption Property (AS2Sender Component)

A URL indicating how the receipt is to be delivered.

Syntax

public string MDNDeliveryOption { get; set; }
Public Property MDNDeliveryOption As String

Default Value

""

Remarks

The default mode of operation is for the receipt to be returned synchronously within the HTTP reply. By specifying a valid URL, the user may request asynchronous delivery instead. The URL indicates the destination for the reply, and may use any appropriate protocol, such as "http", "https", or "mailto".

If MDNDeliveryOption is set to an empty string, the receipt will be returned synchronously, and will be processed automatically by the component. Clients requesting asynchronous delivery should provide their own processing for reading receipts.

MDNOptions Property (AS2Sender Component)

Used to indicate the options requested for the MDN receipt.

Syntax

public string MDNOptions { get; set; }
Public Property MDNOptions As String

Default Value

"signed-receipt-protocol=optional, pkcs7-signature; signed-receipt-micalg=optional, sha-256"

Remarks

By default, the component will request that the MDN be signed with a PKCS#7 signature over a SHA-256 hash, which is the industry standard.

Set MDNOptions to an empty string to request an unsigned receipt.

This property will automatically be updated when SignatureAlgorithm is set. Normally you will not need to set this property, however you can set a value here to override the automatically generated value.

The string format is that of the Disposition-Notification-Options HTTP header, as specified in RFC 3335. As a form of shorthand, you may set this property to "sha1", "sha-256", or "md5" to request the indicated hash algorithm.

MDNReceipt Property (AS2Sender Component)

The MDN receipt returned from the server.

Syntax

public MDNReceipt MDNReceipt { get; set; }
Public Property MDNReceipt As MDNReceipt

Remarks

This property will contain an instance of MDNReceipt with the complete MDN receipt returned from the AS2 receiver. The receipt will be a signed or unsigned multipart/report in MIME format. For synchronous MDN requests, this property is populated automatically after the call to Post. If an asynchronous MDN is sent over HTTP, it may be read from the HTTP context by calling ReadAsyncReceipt, or it may be set manually.

When MDNReceipt is set to a valid MDN receipt, the originator of the receipt will be stored in AS2To, the intended recipient (presumably your system) will be stored in AS2From, and the original message ID will be stored in MessageId.

If you are processing a MDN receipt asynchronously, you can use the values to look up the original message and validate the receipt. Set the OriginalContentMIC, MDNOptions, and ReceiptSignerCert to the values originally computed when the message was sent (if you are requesting async MDNs you must save this information externally.). You can then validate the asynchronous receipt by invoking VerifyReceipt.

Alternatively, AsyncMDNInfoDir may be set in place of OriginalContentMIC, MessageId, and MDNOptions (provided it was set to the same value when the message was sent). If AsyncMDNInfoDir was specified when the message was sent, the component would have saved OriginalContentMIC and MDNOptions to a file identified by the MessageId for the transmission. These properties are read from the file matching the MessageId in the MDNReceipt automatically if AsyncMDNInfoDir is specified.

Note: MDNReceipt must be populated prior to calling VerifyReceipt.

Please refer to the MDNReceipt type for a complete list of fields.

MDNTo Property (AS2Sender Component)

Used to indicate that a message disposition notification is requested.

Syntax

public string MDNTo { get; set; }
Public Property MDNTo As String

Default Value

""

Remarks

If this property is set, a Disposition-Notification-To header will be added to the request, and an MDN will be requested. The value may be an email address, URL, etc., and while its presence is used to determine whether or not an MDN is sent, the value itself will typically be ignored by the server.

By default, the component will request a PKCS#7 signature and synchronous delivery. You may set MDNDeliveryOption to request an asynchronous MDN, and you may set MDNOptions to request a different type of signature, or no signature at all.

MessageId Property (AS2Sender Component)

The Id of the message.

Syntax

public string MessageId { get; set; }
Public Property MessageId As String

Default Value

""

Remarks

The Id format is as in RFC 2822: id-left@id-right .

A unique Id will automatically be generated on startup. Sending a message will reset id-left if the MessageId has been used in the previous message.

If you set MessageId to a string of the form "@(id-right)" a unique id-left will be generated. If you set MessageId to an empty string, a new MessageId will be generated with the same id-right.

After an MDNReceipt is returned or set, MessageId will contain the Original-Message-ID found in the MDN Receipt.

This property is not available at design time.

OriginalContentMIC Property (AS2Sender Component)

The Message Integrity Check(s) (one-way hash) of the outgoing message.

Syntax

public string OriginalContentMIC { get; set; }
Public Property OriginalContentMIC As String

Default Value

""

Remarks

A MIC will be calculated over the outgoing message using the same algorithm in the SignatureAlgorithm configuration used to sign the message. The property will be set when Post (in AS3, Send) is invoked, and the MIC will automatically be checked against the Original-Content-MIC in the MDN for synchronous MDNs.

The format is in RFC 3335, i.e. "w7AguNJEmhF/qIjJw6LnnA==, md5", with a newline at the end.

If you are requesting an asynchronous MDN, you must save this value externally so that it can be loaded when the MDN is received (you may also use AsyncMDNInfoDir).

Proxy Property (AS2Sender Component)

A set of properties related to proxy access.

Syntax

public Proxy Proxy { get; set; }
Public Property Proxy As Proxy

Remarks

This property contains fields describing the proxy through which the component will attempt to connect.

Please refer to the Proxy type for a complete list of fields.

ReceiptSignerCert Property (AS2Sender Component)

The public key certificate for the MDN receipt signature.

Syntax

public Certificate ReceiptSignerCert { get; set; }
Public Property ReceiptSignerCert As Certificate

Remarks

Ordinarily, if your trading partner uses the same certificate for both signing and encryption, the certificate specified in RecipientCert is used for both encryption and verifying the receipt signature.

If your trading partner uses different certificates for signing and encryption, you must set this property to the public key for you partner's signing certificate before invoking Post.

After invoking Post or VerifyReceipt, this will contain the certificate used to sign the receipt, if the receipt is signed.

If set, this property should be a public key instance of Certificate.

Please refer to the Certificate type for a complete list of fields.

RecipientCerts Property (AS2Sender Component)

The public key certificates of the recipients for this message.

Syntax

public CertificateList RecipientCerts { get; }
Public Property RecipientCerts As CertificateList

Remarks

The encryption certificates of the recipients. If this property is specified, the message content will be encrypted using the algorithm given by EncryptionAlgorithm.

This property will also be used to verify signed receipts if ReceiptSignerCert is not specified. In this case, it will use the first certificate found in the collection, if one exists. If your trading partner uses different certificates for signing and encryption, you should set RecipientCerts to the encryption certificate(s) and ReceiptSignerCert to the signing certificate.

If the component is unable to verify a signature make sure RecipientCerts are set appropriately.

If set, this property should could contain public key instances of Certificate.

This property is not available at design time.

Please refer to the Certificate type for a complete list of fields.

RestartDirectory Property (AS2Sender Component)

The directory to log cached files when using AS2 restart functionality.

Syntax

public string RestartDirectory { get; set; }
Public Property RestartDirectory As String

Default Value

""

Remarks

If this property is set, the component will cache all data to the RestartDirectory. Thus, when sending a file is interrupted, the component can restart the transmission of the file starting where it was interrupted.

To use this functionality, simply set the RestartDirectory and call Restart.

When using restart functionality, the data is completely processed to the RestartDirectory before sending begins.

NOTE: This directory will not automatically be cleaned up.

RolloverSigningCert Property (AS2Sender Component)

Contains the certificate to use when signing messages.

Syntax

public Certificate RolloverSigningCert { get; set; }
Public Property RolloverSigningCert As Certificate

Remarks

This is your rollover signing certificate. This may be used to specify an additional signing certificate during a period of transition between private certificates in the application.

If this property is specified, the message content will be signed using both SigningCert and RolloverSigningCert. The recipient will be able to verify the signature with either corresponding public certificate.

If set, this property should be a private key instance of Certificate.

Please refer to the Certificate type for a complete list of fields.

SignatureAlgorithm Property (AS2Sender Component)

Signature algorithm to be used in outgoing messages.

Syntax

public string SignatureAlgorithm { get; set; }
Public Property SignatureAlgorithm As String

Default Value

"sha-256"

Remarks

Signature Algorithm can be set to indicate the preferred signing algorithm. Possible values are:

  • sha1
  • md5
  • sha-256 (or sha256) (default)
  • sha-384 (or sha384)
  • sha-512 (or sha512)
  • sha-224 (or sha224)

The default value is "sha-256". When this property is set the MDNOptions property is automatically updated to request the MDN receipt be signed with the same algorithm.

SigningCert Property (AS2Sender Component)

Contains the certificate to use when signing messages.

Syntax

public Certificate SigningCert { get; set; }
Public Property SigningCert As Certificate

Remarks

This is your signing certificate. If this property is specified, the message content will be signed using the algorithm given by SignatureAlgorithm.

If set, this property should be a private key instance of Certificate.

Please refer to the Certificate type for a complete list of fields.

SSLAcceptServerCert Property (AS2Sender Component)

Instructs the component to unconditionally accept the server certificate that matches the supplied certificate.

Syntax

public Certificate SSLAcceptServerCert { get; set; }
Public Property SSLAcceptServerCert As Certificate

Remarks

If it finds any issues with the certificate presented by the server, the component will normally terminate the connection with an error.

You may override this behavior by supplying a value for SSLAcceptServerCert. If the certificate supplied in SSLAcceptServerCert is the same as the certificate presented by the server, then the server certificate is accepted unconditionally, and the connection will continue normally.

Please note that this functionality is provided only for cases where you otherwise know that you are communicating with the right server. If used improperly, this property may create a security breach. Use it at your own risk.

Please refer to the Certificate type for a complete list of fields.

SSLCert Property (AS2Sender Component)

The certificate to be used during SSL negotiation.

Syntax

public Certificate SSLCert { get; set; }
Public Property SSLCert As Certificate

Remarks

The digital certificate that the component will use during SSL negotiation. Set this property to a valid certificate before starting SSL negotiation. To set a certificate, you may set the Encoded field to the encoded certificate. To select a certificate, use the store and subject fields.

Please refer to the Certificate type for a complete list of fields.

SSLProvider Property (AS2Sender Component)

This specifies the SSL/TLS implementation to use.

Syntax

public As2senderSSLProviders SSLProvider { get; set; }

enum As2senderSSLProviders { sslpAutomatic, sslpPlatform, sslpInternal }
Public Property SSLProvider As As2senderSSLProviders

Enum As2senderSSLProviders sslpAutomatic sslpPlatform sslpInternal End Enum

Default Value

0

Remarks

This property specifies the SSL/TLS implementation to use. In most cases the default value of 0 (Automatic) is recommended and should not be changed. When set to 0 (Automatic) the component will select whether to use the platform implementation or the internal implementation depending on the operating system as well as the TLS version being used.

Possible values are:

0 (sslpAutomatic - default)Automatically selects the appropriate implementation.
1 (sslpPlatform) Uses the platform/system implementation.
2 (sslpInternal) Uses the internal implementation.
Additional Notes

In most cases using the default value (Automatic) is recommended. The component will select a provider depending on the current platform.

When Automatic is selected, on Windows the component will use the platform implementation. On Linux/macOS the component will use the internal implementation. When TLS 1.3 is enabled via SSLEnabledProtocols the internal implementation is used on all platforms.

The .NET Standard library will always use the internal implementation on all platforms.

SSLServerCert Property (AS2Sender Component)

The server certificate for the last established connection.

Syntax

public Certificate SSLServerCert { get; }
Public ReadOnly Property SSLServerCert As Certificate

Remarks

SSLServerCert contains the server certificate for the last established connection.

SSLServerCert is reset every time a new connection is attempted.

This property is read-only.

Please refer to the Certificate type for a complete list of fields.

Subject Property (AS2Sender Component)

The subject of the message.

Syntax

public string Subject { get; set; }
Public Property Subject As String

Default Value

""

Remarks

The optional human-readable subject of the message. Some AS2 partners will use this field to send additional information about the transmission at the transport layer.

Timeout Property (AS2Sender Component)

A timeout for the component.

Syntax

public int Timeout { get; set; }
Public Property Timeout As Integer

Default Value

60

Remarks

If the Timeout property is set to 0, all operations will run uninterrupted until successful completion or an error condition is encountered.

If Timeout is set to a positive value, the component will wait for the operation to complete before returning control.

The component will use DoEvents to enter an efficient wait loop during any potential waiting period, making sure that all system events are processed immediately as they arrive. This ensures that the host application does not "freeze" and remains responsive.

If Timeout expires, and the operation is not yet complete, the component throws an exception.

Please note that by default, all timeouts are inactivity timeouts, i.e. the timeout period is extended by Timeout seconds when any amount of data is successfully sent or received.

The default value for the Timeout property is 60 seconds.

URL Property (AS2Sender Component)

The URL to which the request is made.

Syntax

public string URL { get; set; }
Public Property URL As String

Default Value

""

Remarks

This property specifies the URL to which the request is made. SSL will be used if and only if the URL scheme is "https".

UseOAEP Property (AS2Sender Component)

This property specifies whether or not to use Optimal Asymmetric Encryption Padding (OAEP).

Syntax

public bool UseOAEP { get; set; }
Public Property UseOAEP As Boolean

Default Value

False

Remarks

This property specifies whether or not to use Optimal Asymmetric Encryption Padding (OAEP). By default, this value is False and the component will use PKCS1.

To specify nondefault OAEP options, please see OAEPRSAHashAlgorithm, OAEPMGF1HashAlgorithm, and OAEPParams

UsePSS Property (AS2Sender Component)

This property specifies whether or not RSA-PSS will be used during signing and verification.

Syntax

public bool UsePSS { get; set; }
Public Property UsePSS As Boolean

Default Value

False

Remarks

This property specifies whether or not RSA-PSS will be used when signing and verifying messages. The default value is False.

UserAgent Property (AS2Sender Component)

Information about the user agent.

Syntax

public string UserAgent { get; set; }
Public Property UserAgent As String

Default Value

"IPWorks EDI AS2Sender Component - www.nsoftware.com"

Remarks

You may override the default with the name and version of your software.

Config Method (AS2Sender Component)

Sets or retrieves a configuration setting.

Syntax

public string Config(string configurationString);

Async Version
public async Task<string> Config(string configurationString);
public async Task<string> Config(string configurationString, CancellationToken cancellationToken);
Public Function Config(ByVal ConfigurationString As String) As String

Async Version
Public Function Config(ByVal ConfigurationString As String) As Task(Of String)
Public Function Config(ByVal ConfigurationString As String, cancellationToken As CancellationToken) As Task(Of String)

Remarks

Config is a generic method available in every component. It is used to set and retrieve configuration settings for the component.

These settings are similar in functionality to properties, but they are rarely used. In order to avoid "polluting" the property namespace of the component, access to these internal properties is provided through the Config method.

To set a configuration setting named PROPERTY, you must call Config("PROPERTY=VALUE"), where VALUE is the value of the setting expressed as a string. For boolean values, use the strings "True", "False", "0", "1", "Yes", or "No" (case does not matter).

To read (query) the value of a configuration setting, you must call Config("PROPERTY"). The value will be returned as a string.

DoEvents Method (AS2Sender Component)

Processes events from the internal message queue.

Syntax

public void DoEvents();

Async Version
public async Task DoEvents();
public async Task DoEvents(CancellationToken cancellationToken);
Public Sub DoEvents()

Async Version
Public Sub DoEvents() As Task
Public Sub DoEvents(cancellationToken As CancellationToken) As Task

Remarks

When DoEvents is called, the component processes any available events. If no events are available, it waits for a preset period of time, and then returns.

Interrupt Method (AS2Sender Component)

Interrupt the current method.

Syntax

public void Interrupt();

Async Version
public async Task Interrupt();
public async Task Interrupt(CancellationToken cancellationToken);
Public Sub Interrupt()

Async Version
Public Sub Interrupt() As Task
Public Sub Interrupt(cancellationToken As CancellationToken) As Task

Remarks

If there is no method in progress, Interrupt simply returns, doing nothing.

Post Method (AS2Sender Component)

Post data to the AS2 server, and check the receipt.

Syntax

public void Post();

Async Version
public async Task Post();
public async Task Post(CancellationToken cancellationToken);
Public Sub Post()

Async Version
Public Sub Post() As Task
Public Sub Post(cancellationToken As CancellationToken) As Task

Remarks

Post data to the server. The reply will also be checked, and if a synchronous MDN was requested (i.e., MDNTo is not empty), it will be validated. After the method finishes, the MDNReceipt, ReceiptSigningProtocol, and ReceiptSignerCert properties will be populated with the appropriate values.

The method operates synchronously, and will throw an exception if any errors or warnings occur. Errors might include a failure to decrypt or authenticate the receipt, the absence of an MDN when one was requested, TCP/IP errors, or any errors reported by the server in the MDN. Warnings might include the return of an unsigned receipt when a signed receipt was requested, or other warnings reported by the server in the MDN.

If an exception is thrown the error code will correspond to the severity of the warning or error, allowing client software to determine whether or not to accept the reply. If multiple errors occur, the exception will return a special error code, and the error message will contain a line for each error's code and description; i.e. "423: Failed to authenticate sender". If the error(s) is/are not fatal processing will not be interrupted, and the relevant properties will be populated as normal.

ReadAsyncReceipt Method (AS2Sender Component)

Reads an asynchronous MDN receipt from the current HTTP session.

Syntax

public void ReadAsyncReceipt();

Async Version
public async Task ReadAsyncReceipt();
public async Task ReadAsyncReceipt(CancellationToken cancellationToken);
Public Sub ReadAsyncReceipt()

Async Version
Public Sub ReadAsyncReceipt() As Task
Public Sub ReadAsyncReceipt(cancellationToken As CancellationToken) As Task

Remarks

ReadAsyncReceipt is used to read an asynchronous MDN receipt from the current HttpContext . The component will fetch the request stream from the HTTP session. MDNReceipt will be populated with a new instance of MDNReceipt.

Reset Method (AS2Sender Component)

Resets the state of the control.

Syntax

public void Reset();

Async Version
public async Task Reset();
public async Task Reset(CancellationToken cancellationToken);
Public Sub Reset()

Async Version
Public Sub Reset() As Task
Public Sub Reset(cancellationToken As CancellationToken) As Task

Remarks

Resets all HTTP headers as well as EDIData, etc. After invoking this method the component may be reused as if it were newly created.

Restart Method (AS2Sender Component)

Restart sending of the file specified by the Etag property.

Syntax

public void Restart();

Async Version
public async Task Restart();
public async Task Restart(CancellationToken cancellationToken);
Public Sub Restart()

Async Version
Public Sub Restart() As Task
Public Sub Restart(cancellationToken As CancellationToken) As Task

Remarks

This method should be called when using the AS2 restart functionality. When called, the component will process the file and cache the processed contents to the RestartDirectory. Before sending, the Etag property will be populated with a unique Etag which identifies the processed file.

If sending is interrupted or fails, this method should be called to restart sending of the previously processed file starting where the interruption occurred. In order to restart from the last transfer, the Etag must be populated with the value from the last connection.

NOTE: When using restart functionality, the data is completely processed to the RestartDirectory before sending begins.

SendCEMRequest Method (AS2Sender Component)

Sends a Certificate Exchange Messaging (CEM) request.

Syntax

public void SendCEMRequest(string requestId);

Async Version
public async Task SendCEMRequest(string requestId);
public async Task SendCEMRequest(string requestId, CancellationToken cancellationToken);
Public Sub SendCEMRequest(ByVal RequestId As String)

Async Version
Public Sub SendCEMRequest(ByVal RequestId As String) As Task
Public Sub SendCEMRequest(ByVal RequestId As String, cancellationToken As CancellationToken) As Task

Remarks

This method send the Certificate Exchange Messaging (CEM) request with the details specified in CEMDetails.

Certificate Exchange Messaging (CEM) allows for new certificates to be sent to a recipient and be automatically updated. This removes the requirement to manually send new certificates to a partner via email or other means. When both sides support this functionality updating certificates can be accomplished in a short period of time.

To prepare a CEM request populate the CEMDetails collection with at least one certificate. For instance if the certificate of the application will be updated soon, the CEMDetails may be populated with the corresponding public certificate to be sent to your partner. CEMDetails should only contain public certificates.

Set RespondByDate to the date by which you expect a response. The format is of the XML standard dateTime type expressed in local time with UTC offset. For instance: "2005-08-31T00:21:00-05:00".

Optionally set CertId to a friendly identifier that the partner may use to help understand the purpose of the new certificate. For instance "New.Encryption.Cert.2014".

Set ResponseURL to the publicly accessible URL where the CEM response will be sent after the partner processes it.

The RequestId parameter uniquely identifies this CEM request and must be saved for use later when receiving the CEM response.

When calling this method the applicable CEMDetails fields are:

SendCEMResponse Method (AS2Sender Component)

Sends a Certificate Exchange Messaging (CEM) response.

Syntax

public void SendCEMResponse(string requestId);

Async Version
public async Task SendCEMResponse(string requestId);
public async Task SendCEMResponse(string requestId, CancellationToken cancellationToken);
Public Sub SendCEMResponse(ByVal RequestId As String)

Async Version
Public Sub SendCEMResponse(ByVal RequestId As String) As Task
Public Sub SendCEMResponse(ByVal RequestId As String, cancellationToken As CancellationToken) As Task

Remarks

This method send the Certificate Exchange Messaging (CEM) request with the details specified in CEMDetails.

A CEM request must have previously been received using AS2Receiver. To send the CEM response, populate CEMDetails with the certificate information and decide whether to accept or reject the request. The following fields may be set to specify the certificate:

Alternatively, the certificate information may be set:

After specifying the certificate information choose whether to accept or reject the request. To accept the request set Accepted to True. To reject the request set Accepted to False and specify a reason in RejectionReason.

Call SendCEMResponse and pass the CEM request Id that was retrieved from the request.

SetRequestHeader Method (AS2Sender Component)

Allows the user to set or add arbitrary HTTP request headers.

Syntax

public void SetRequestHeader(string headerName, string headerValue);

Async Version
public async Task SetRequestHeader(string headerName, string headerValue);
public async Task SetRequestHeader(string headerName, string headerValue, CancellationToken cancellationToken);
Public Sub SetRequestHeader(ByVal HeaderName As String, ByVal HeaderValue As String)

Async Version
Public Sub SetRequestHeader(ByVal HeaderName As String, ByVal HeaderValue As String) As Task
Public Sub SetRequestHeader(ByVal HeaderName As String, ByVal HeaderValue As String, cancellationToken As CancellationToken) As Task

Remarks

HeaderName should contain the header name, and HeaderValue should contain its value. Use this to set headers such as To, Date, etc. Note that a default value for Date will automatically be determined and this method may be used to override the default.

SetRequestHeader may be used to set any header except for the following: AS2-To, AS2-From, AS2-Version, Subject, Message-Id, Disposition-Notification-To, Disposition-Notification-Options, Receipt-Delivery-Option, Host, Content-Length.

SetTPInfo Method (AS2Sender Component)

A convenient way to set AS2 communication parameters using XML strings.

Syntax

public void SetTPInfo(string profile);

Async Version
public async Task SetTPInfo(string profile);
public async Task SetTPInfo(string profile, CancellationToken cancellationToken);
Public Sub SetTPInfo(ByVal Profile As String)

Async Version
Public Sub SetTPInfo(ByVal Profile As String) As Task
Public Sub SetTPInfo(ByVal Profile As String, cancellationToken As CancellationToken) As Task

Remarks

SetTPInfo offers a convenient way to set AS2 communication parameters using XML strings. The format of the XML is the same as provided by the method GetTPInfo of AS2ProfileMgr.

The "self" information should always precede the partner information as shown below. AS2Sender as2sender = new AS2Sender(); AS2Profilemgr mgr = new AS2Profilemgr(); mgr.DataDir = @"C:\as2data"; as2sender.SetTPInfo(mgr.GetTPInfo("self")); as2sender.SetTPInfo(mgr.GetTPInfo("partnerOrg")); as2sender.EDIFile = @"C:\as2Data.x12"; as2sender.Post();

VerifyReceipt Method (AS2Sender Component)

Verifies an asynchronous MDN receipt.

Syntax

public void VerifyReceipt();

Async Version
public async Task VerifyReceipt();
public async Task VerifyReceipt(CancellationToken cancellationToken);
Public Sub VerifyReceipt()

Async Version
Public Sub VerifyReceipt() As Task
Public Sub VerifyReceipt(cancellationToken As CancellationToken) As Task

Remarks

VerifyReceipt verifies the receipt in MDNReceipt against OriginalContentMIC, MessageId and the preferences specified in MDNOptions. The method operates similarly to Post: After the method finishes, the MDNReceipt, ReceiptSigningProtocol, and ReceiptSignerCert properties will be populated with the appropriate values.

The method operates synchronously, and will throw an exception if any errors or warnings occur. Errors might include a failure to decrypt or authenticate the receipt, the absence of an MDN when one was requested, TCP/IP errors, or any errors reported by the server in the MDN. Warnings might include the return of an unsigned receipt when a signed receipt was requested, or other warnings reported by the server in the MDN.

If an exception is thrown the error code will correspond to the severity of the warning or error, allowing client software to determine whether or not to accept the reply. If multiple errors occur, the exception will return a special error code, and the error message will contain a line for each error's code and description; i.e. "423: Failed to authenticate sender". If the error(s) is/are not fatal processing will not be interrupted, and the relevant properties will be populated as normal.

This method should be used to verify receipts received asynchronously; i.e., not in the HTTP reply to a POST. When posting, asynchronous MDN delivery may be requested by setting MDNDeliveryOption.

Connected Event (AS2Sender Component)

This event is fired immediately after a connection completes (or fails).

Syntax

public event OnConnectedHandler OnConnected;

public delegate void OnConnectedHandler(object sender, As2senderConnectedEventArgs e);

public class As2senderConnectedEventArgs : EventArgs {
  public int StatusCode { get; }
  public string Description { get; }
}
Public Event OnConnected As OnConnectedHandler

Public Delegate Sub OnConnectedHandler(sender As Object, e As As2senderConnectedEventArgs)

Public Class As2senderConnectedEventArgs Inherits EventArgs
  Public ReadOnly Property StatusCode As Integer
  Public ReadOnly Property Description As String
End Class

Remarks

If the connection is made normally, StatusCode is 0 and Description is "OK".

If the connection fails, StatusCode has the error code returned by the Transmission Control Protocol (TCP)/IP stack. Description contains a description of this code. The value of StatusCode is equal to the value of the error.

Please refer to the Error Codes section for more information.

Disconnected Event (AS2Sender Component)

This event is fired when a connection is closed.

Syntax

public event OnDisconnectedHandler OnDisconnected;

public delegate void OnDisconnectedHandler(object sender, As2senderDisconnectedEventArgs e);

public class As2senderDisconnectedEventArgs : EventArgs {
  public int StatusCode { get; }
  public string Description { get; }
}
Public Event OnDisconnected As OnDisconnectedHandler

Public Delegate Sub OnDisconnectedHandler(sender As Object, e As As2senderDisconnectedEventArgs)

Public Class As2senderDisconnectedEventArgs Inherits EventArgs
  Public ReadOnly Property StatusCode As Integer
  Public ReadOnly Property Description As String
End Class

Remarks

If the connection is broken normally, StatusCode is 0 and Description is "OK".

If the connection is broken for any other reason, StatusCode has the error code returned by the Transmission Control Protocol (TCP/IP) subsystem. Description contains a description of this code. The value of StatusCode is equal to the value of the TCP/IP error.

Please refer to the Error Codes section for more information.

EndTransfer Event (AS2Sender Component)

This event is fired when a document finishes transferring.

Syntax

public event OnEndTransferHandler OnEndTransfer;

public delegate void OnEndTransferHandler(object sender, As2senderEndTransferEventArgs e);

public class As2senderEndTransferEventArgs : EventArgs {
  public int Direction { get; }
}
Public Event OnEndTransfer As OnEndTransferHandler

Public Delegate Sub OnEndTransferHandler(sender As Object, e As As2senderEndTransferEventArgs)

Public Class As2senderEndTransferEventArgs Inherits EventArgs
  Public ReadOnly Property Direction As Integer
End Class

Remarks

The EndTransfer event is fired first when the client finishes sending data to the server (in a POST or PUT request) and then when the document text finishes transferring from the server to the local host.

The Direction parameter shows whether the client (0) or the server (1) is sending the data.

Error Event (AS2Sender Component)

Fired when information is available about errors during data delivery.

Syntax

public event OnErrorHandler OnError;

public delegate void OnErrorHandler(object sender, As2senderErrorEventArgs e);

public class As2senderErrorEventArgs : EventArgs {
  public int ErrorCode { get; }
  public string Description { get; }
}
Public Event OnError As OnErrorHandler

Public Delegate Sub OnErrorHandler(sender As Object, e As As2senderErrorEventArgs)

Public Class As2senderErrorEventArgs Inherits EventArgs
  Public ReadOnly Property ErrorCode As Integer
  Public ReadOnly Property Description As String
End Class

Remarks

The Error event is fired in case of exceptional conditions during message processing. Normally the component throws an exception.

The ErrorCode parameter contains an error code, and the Description parameter contains a textual description of the error. For a list of valid error codes and their descriptions, please refer to the Error Codes section.

Header Event (AS2Sender Component)

This event is fired every time a header line comes in.

Syntax

public event OnHeaderHandler OnHeader;

public delegate void OnHeaderHandler(object sender, As2senderHeaderEventArgs e);

public class As2senderHeaderEventArgs : EventArgs {
  public string Field { get; }
  public string Value { get; }
}
Public Event OnHeader As OnHeaderHandler

Public Delegate Sub OnHeaderHandler(sender As Object, e As As2senderHeaderEventArgs)

Public Class As2senderHeaderEventArgs Inherits EventArgs
  Public ReadOnly Property Field As String
  Public ReadOnly Property Value As String
End Class

Remarks

The Field parameter contains the name of the HTTP header (same case as it is delivered). The Value parameter contains the header contents.

If the header line being retrieved is a continuation header line, then the Field parameter contains an empty string.

Note that only the top-level headers will be returned through this event, and that they are available through the ReplyHeaders property.

The Field parameter contains the name of the HTTP header (which is the same as it is delivered). The Value parameter contains the header contents.

If the header line being retrieved is a continuation header line, then the Field parameter contains "" (empty string).

Log Event (AS2Sender Component)

Fired with log information while processing a message.

Syntax

public event OnLogHandler OnLog;

public delegate void OnLogHandler(object sender, As2senderLogEventArgs e);

public class As2senderLogEventArgs : EventArgs {
  public string LogType { get; }
  public string LogMessage { get; }
public byte[] LogMessageB { get; } }
Public Event OnLog As OnLogHandler

Public Delegate Sub OnLogHandler(sender As Object, e As As2senderLogEventArgs)

Public Class As2senderLogEventArgs Inherits EventArgs
  Public ReadOnly Property LogType As String
  Public ReadOnly Property LogMessage As String
Public ReadOnly Property LogMessageB As Byte() End Class

Remarks

This event fires once for each log message generated by the component. The verbosity is controlled by the LogLevel setting.

Log messages available through this event correspond to log files written to LogDirectory. This event provides a way to obtain log messages without relying on files on disk. This event fires regardless of the value of LogDirectory (i.e. when LogDirectory is empty the event will still fire).

The LogMessage event parameter holds the raw log data.

The LogType event parameter indicates the type of log. Possible values are:

"LOG" Information about the status of the process.
"ERR" An error was encountered.
"DAT" The EDI payload.
"REQ" The raw request
"MDN" The MDN response.
"DEBUG" Debug information.
"DAT.INPUT" Debug information when processing payload. Only applicable when LogDebug is True.
"DAT.ENCRYPT" Debug information when processing payload. Only applicable when LogDebug is True.
"DAT.COMPRESS" Debug information when processing payload. Only applicable when LogDebug is True.
"DAT.SIGN" Debug information when processing payload. Only applicable when LogDebug is True.
"DAT.DECRYPT" Debug information when processing payload. Only applicable when LogDebug is True.
"DAT.DECOMPRESS" Debug information when processing payload. Only applicable when LogDebug is True.
"DAT.VERIFY" Debug information when processing payload. Only applicable when LogDebug is True.
"DAT.DEBUG" Debug information when processing payload. Only applicable when LogDebug is True.

SetCookie Event (AS2Sender Component)

This event is fired for every cookie set by the server.

Syntax

public event OnSetCookieHandler OnSetCookie;

public delegate void OnSetCookieHandler(object sender, As2senderSetCookieEventArgs e);

public class As2senderSetCookieEventArgs : EventArgs {
  public string Name { get; }
  public string Value { get; }
  public string Expires { get; }
  public string Domain { get; }
  public string Path { get; }
  public bool Secure { get; }
}
Public Event OnSetCookie As OnSetCookieHandler

Public Delegate Sub OnSetCookieHandler(sender As Object, e As As2senderSetCookieEventArgs)

Public Class As2senderSetCookieEventArgs Inherits EventArgs
  Public ReadOnly Property Name As String
  Public ReadOnly Property Value As String
  Public ReadOnly Property Expires As String
  Public ReadOnly Property Domain As String
  Public ReadOnly Property Path As String
  Public ReadOnly Property Secure As Boolean
End Class

Remarks

The SetCookie event is fired for every Set-Cookie: header received from the HTTP server.

The Name parameter contains the name of the cookie, with the corresponding value supplied in the Value parameter.

The Expires parameter contains an expiration time for the cookie (if provided by the server). The time format used is "Weekday, DD-Mon-YY HH:MM:SS GMT". If the server does not provide an expiration time, the Expires parameter will be an empty string. In this case, the convention is to drop the cookie at the end of the session.

The Domain parameter contains a domain name to limit the cookie to (if provided by the server). If the server does not provide a domain name, the Domain parameter will be an empty string. The convention in this case is to use the server specified in the URL (URLServer) as the cookie domain.

The Path parameter contains a path name to limit the cookie to (if provided by the server). If the server does not provide a cookie path, the Path parameter will be an empty string. The convention in this case is to use the path specified in the URL (URLPath) as the cookie path.

The Secure parameter specifies whether the cookie is secure. If the value of this parameter is True, the cookie value must be submitted only through a secure (HTTPS) connection.

SignerCertInfo Event (AS2Sender Component)

This event is fired during verification of the signed message.

Syntax

public event OnSignerCertInfoHandler OnSignerCertInfo;

public delegate void OnSignerCertInfoHandler(object sender, As2senderSignerCertInfoEventArgs e);

public class As2senderSignerCertInfoEventArgs : EventArgs {
  public string Issuer { get; }
  public string SerialNumber { get; }
  public string SubjectKeyIdentifier { get; }
  public string CertEncoded { get; }
public byte[] CertEncodedB { get; } }
Public Event OnSignerCertInfo As OnSignerCertInfoHandler

Public Delegate Sub OnSignerCertInfoHandler(sender As Object, e As As2senderSignerCertInfoEventArgs)

Public Class As2senderSignerCertInfoEventArgs Inherits EventArgs
  Public ReadOnly Property Issuer As String
  Public ReadOnly Property SerialNumber As String
  Public ReadOnly Property SubjectKeyIdentifier As String
  Public ReadOnly Property CertEncoded As String
Public ReadOnly Property CertEncodedB As Byte() End Class

Remarks

During verification, this event will be raised while parsing the signer's certificate information. The parameters that are populated depend on the options used when the message was originally signed. This information may be used to select the correct certificate for SignerCert to verify the signature. The following parameters may be populated:

Issuer specifies the subject of the issuer of the certificate used to sign the message.

SerialNumber is the serial number of the certificate used to sign the message.

SubjectKeyIdentifier is the X.509 subjectKeyIdentifier extension value of the certificate used to sign the message encoded as a hex string.

CertEncoded is the PEM (Base64 encoded) public certificate needed to verify the signature.

Note: When this value is present, the component will automatically use this value to perform signature verification.

The SignerCert property may be set from within this event. In this manner, the decision of which signer certificate to load may be delayed until the parameters of this event are inspected and the correct certificate can be located and loaded.

SSLServerAuthentication Event (AS2Sender Component)

Fired after the server presents its certificate to the client.

Syntax

public event OnSSLServerAuthenticationHandler OnSSLServerAuthentication;

public delegate void OnSSLServerAuthenticationHandler(object sender, As2senderSSLServerAuthenticationEventArgs e);

public class As2senderSSLServerAuthenticationEventArgs : EventArgs {
  public string CertEncoded { get; }
public byte[] CertEncodedB { get; } public string CertSubject { get; } public string CertIssuer { get; } public string Status { get; } public bool Accept { get; set; } }
Public Event OnSSLServerAuthentication As OnSSLServerAuthenticationHandler

Public Delegate Sub OnSSLServerAuthenticationHandler(sender As Object, e As As2senderSSLServerAuthenticationEventArgs)

Public Class As2senderSSLServerAuthenticationEventArgs Inherits EventArgs
  Public ReadOnly Property CertEncoded As String
Public ReadOnly Property CertEncodedB As Byte() Public ReadOnly Property CertSubject As String Public ReadOnly Property CertIssuer As String Public ReadOnly Property Status As String Public Property Accept As Boolean End Class

Remarks

This event is where the client can decide whether to continue with the connection process or not. The Accept parameter is a recommendation on whether to continue or close the connection. This is just a suggestion: application software must use its own logic to determine whether to continue or not.

When Accept is False, Status shows why the verification failed (otherwise, Status contains the string "OK").

SSLStatus Event (AS2Sender Component)

Fired when secure connection progress messages are available.

Syntax

public event OnSSLStatusHandler OnSSLStatus;

public delegate void OnSSLStatusHandler(object sender, As2senderSSLStatusEventArgs e);

public class As2senderSSLStatusEventArgs : EventArgs {
  public string Message { get; }
}
Public Event OnSSLStatus As OnSSLStatusHandler

Public Delegate Sub OnSSLStatusHandler(sender As Object, e As As2senderSSLStatusEventArgs)

Public Class As2senderSSLStatusEventArgs Inherits EventArgs
  Public ReadOnly Property Message As String
End Class

Remarks

The event is fired for informational and logging purposes only. This event tracks the progress of the connection.

StartTransfer Event (AS2Sender Component)

This event is fired when a document starts transferring (after the headers).

Syntax

public event OnStartTransferHandler OnStartTransfer;

public delegate void OnStartTransferHandler(object sender, As2senderStartTransferEventArgs e);

public class As2senderStartTransferEventArgs : EventArgs {
  public int Direction { get; }
}
Public Event OnStartTransfer As OnStartTransferHandler

Public Delegate Sub OnStartTransferHandler(sender As Object, e As As2senderStartTransferEventArgs)

Public Class As2senderStartTransferEventArgs Inherits EventArgs
  Public ReadOnly Property Direction As Integer
End Class

Remarks

The StartTransfer event is fired first when the client starts sending data to the server (in a POST or PUT request) and then when the document text starts transferring from the server to the local host.

The Direction parameter shows whether the client (0) or the server (1) is sending the data.

Transfer Event (AS2Sender Component)

This event is fired while a document transfers (delivers document).

Syntax

public event OnTransferHandler OnTransfer;

public delegate void OnTransferHandler(object sender, As2senderTransferEventArgs e);

public class As2senderTransferEventArgs : EventArgs {
  public int Direction { get; }
  public long BytesTransferred { get; }
  public int PercentDone { get; }
  public string Text { get; }
public byte[] TextB { get; } }
Public Event OnTransfer As OnTransferHandler

Public Delegate Sub OnTransferHandler(sender As Object, e As As2senderTransferEventArgs)

Public Class As2senderTransferEventArgs Inherits EventArgs
  Public ReadOnly Property Direction As Integer
  Public ReadOnly Property BytesTransferred As Long
  Public ReadOnly Property PercentDone As Integer
  Public ReadOnly Property Text As String
Public ReadOnly Property TextB As Byte() End Class

Remarks

The Text parameter contains the portion of the document text being received. It is empty if data are being posted to the server.

The BytesTransferred parameter contains the number of bytes transferred in this Direction since the beginning of the document text (excluding HTTP response headers).

The Direction parameter shows whether the client (0) or the server (1) is sending the data.

The PercentDone parameter shows the progress of the transfer in the corresponding direction. If PercentDone can not be calculated the value will be -1.

Note: Events are not re-entrant. Performing time-consuming operations within this event will prevent it from firing again in a timely manner and may affect overall performance.

CEMDetail Type

This type defines details about the CEM request.

Remarks

This type defines details about the CEM request. Not all fields are applicable for all operations.

Fields

Accepted
bool

Default Value: False

Whether the CEM request is accepted.

Before calling SendCEMResponse set this to True to accept the CEM request.

When processing a CEM response check this field to determine if the request was accepted.

CertId
string

Default Value: ""

A user defined identifier for the certificate.

This field defines a user specified identifier for the certificate. This may be set to a value which helps the recipient identify the certificate. For instance "CompanyA.Encryption.Cert.2014".

This field may be set before calling SendCEMRequest or SendCEMResponse from AS2Sender.

This field may be queried when received a CEM request or response with AS2Receiver.

CertIssuer
string

Default Value: ""

This field holds the issuer of the certificate. This may be queried when receiving a CEM request with AS2Receiver. This may be set before calling SendCEMResponse with AS2Sender.

CertSerialNumber
string

Default Value: ""

This field holds the serial number of the certificate. This may be queried when receiving a CEM request with AS2Receiver. This may be set before calling SendCEMResponse with AS2Sender.

CertStore
string

Default Value: "MY"

The name of the certificate store for the certificate.

This field defines the store location for the type specified by CertStoreType.

Designations of certificate stores are platform dependent.

The following designations are the most common User and Machine certificate stores in Windows:

MYA certificate store holding personal certificates with their associated private keys.
CACertifying authority certificates.
ROOTRoot certificates.

When the certificate store type is PFXFile, this property must be set to the name of the file. When the type is PFXBlob, the property must be set to the binary contents of a PFX file (i.e., PKCS#12 certificate store).

CertStoreB
byte []

Default Value: "MY"

The name of the certificate store for the certificate.

This field defines the store location for the type specified by CertStoreType.

Designations of certificate stores are platform dependent.

The following designations are the most common User and Machine certificate stores in Windows:

MYA certificate store holding personal certificates with their associated private keys.
CACertifying authority certificates.
ROOTRoot certificates.

When the certificate store type is PFXFile, this property must be set to the name of the file. When the type is PFXBlob, the property must be set to the binary contents of a PFX file (i.e., PKCS#12 certificate store).

CertStorePassword
string

Default Value: ""

If the certificate store is of a type that requires a password, this property is used to specify that password in order to open the certificate store.

CertStoreType
CertStoreTypes

Default Value: 0

The type of certificate store for this certificate.

The component supports both public and private keys in a variety of formats. When the cstAuto value is used, the component will automatically determine the type. This field can take one of the following values:

0 (cstUser - default)For Windows, this specifies that the certificate store is a certificate store owned by the current user.

Note: This store type is not available in Java.

1 (cstMachine)For Windows, this specifies that the certificate store is a machine store.

Note: This store type is not available in Java.

2 (cstPFXFile)The certificate store is the name of a PFX (PKCS#12) file containing certificates.
3 (cstPFXBlob)The certificate store is a string (binary or Base64-encoded) representing a certificate store in PFX (PKCS#12) format.
4 (cstJKSFile)The certificate store is the name of a Java Key Store (JKS) file containing certificates.

Note: This store type is only available in Java.

5 (cstJKSBlob)The certificate store is a string (binary or Base64-encoded) representing a certificate store in Java Key Store (JKS) format.

Note: this store type is only available in Java.

6 (cstPEMKeyFile)The certificate store is the name of a PEM-encoded file that contains a private key and an optional certificate.
7 (cstPEMKeyBlob)The certificate store is a string (binary or Base64-encoded) that contains a private key and an optional certificate.
8 (cstPublicKeyFile)The certificate store is the name of a file that contains a PEM- or DER-encoded public key certificate.
9 (cstPublicKeyBlob)The certificate store is a string (binary or Base64-encoded) that contains a PEM- or DER-encoded public key certificate.
10 (cstSSHPublicKeyBlob)The certificate store is a string (binary or Base64-encoded) that contains an SSH-style public key.
11 (cstP7BFile)The certificate store is the name of a PKCS#7 file containing certificates.
12 (cstP7BBlob)The certificate store is a string (binary) representing a certificate store in PKCS#7 format.
13 (cstSSHPublicKeyFile)The certificate store is the name of a file that contains an SSH-style public key.
14 (cstPPKFile)The certificate store is the name of a file that contains a PPK (PuTTY Private Key).
15 (cstPPKBlob)The certificate store is a string (binary) that contains a PPK (PuTTY Private Key).
16 (cstXMLFile)The certificate store is the name of a file that contains a certificate in XML format.
17 (cstXMLBlob)The certificate store is a string that contains a certificate in XML format.
18 (cstJWKFile)The certificate store is the name of a file that contains a JWK (JSON Web Key).
19 (cstJWKBlob)The certificate store is a string that contains a JWK (JSON Web Key).
21 (cstBCFKSFile)The certificate store is the name of a file that contains a BCFKS (Bouncy Castle FIPS Key Store).

Note: This store type is only available in Java and .NET.

22 (cstBCFKSBlob)The certificate store is a string (binary or Base64-encoded) representing a certificate store in BCFKS (Bouncy Castle FIPS Key Store) format.

Note: This store type is only available in Java and .NET.

23 (cstPKCS11)The certificate is present on a physical security key accessible via a PKCS#11 interface.

To use a security key, the necessary data must first be collected using the CertMgr component. The ListStoreCertificates method may be called after setting CertStoreType to cstPKCS11, CertStorePassword to the PIN, and CertStore to the full path of the PKCS#11 DLL. The certificate information returned in the CertList event's CertEncoded parameter may be saved for later use.

When using a certificate, pass the previously saved security key information as the Store and set StorePassword to the PIN.

Code Example. SSH Authentication with Security Key: certmgr.CertStoreType = CertStoreTypes.cstPKCS11; certmgr.OnCertList += (s, e) => { secKeyBlob = e.CertEncoded; }; certmgr.CertStore = @"C:\Program Files\OpenSC Project\OpenSC\pkcs11\opensc-pkcs11.dll"; certmgr.CertStorePassword = "123456"; //PIN certmgr.ListStoreCertificates(); sftp.SSHCert = new Certificate(CertStoreTypes.cstPKCS11, secKeyBlob, "123456", "*"); sftp.SSHUser = "test"; sftp.SSHLogon("myhost", 22);

99 (cstAuto)The store type is automatically detected from the input data. This setting may be used with both public and private keys and can detect any of the supported formats automatically.

CertSubject
string

Default Value: ""

The subject of the certificate.

CertUsage
int

Default Value: 15

This field defines which usages are applicable to the certificate. This may be set to a binary 'OR' of one or more of the following values:

  • 1 (TLS Client)
  • 2 (TLS Server)
  • 4 (Encryption)
  • 8 (Signature)
The default value is "15", meaning all usages are allowed.

RejectionReason
string

Default Value: ""

If Accepted is False this field specifies the reason a request was rejected.

When using AS2Sender this may be set to a string value which the recipient will see.

When using AS2Receiver query this field for details on why the request was rejected.

RespondByDate
string

Default Value: ""

This field specifies the date by which the other party should respond. If the other party does not respond the new certificate may be used without any further notice. This field exists to assist the recipient in knowing when they should respond by. It does not guarantee a response by the specified date.

The format is of the XML standard dateTime type expressed in local time with UTC offset. For instance: "2005-08-31T00:21:00-05:00".

When using AS2Sender set this before calling SendCEMRequest.

When using AS2Receiver this field may be queried.

ResponseURL
string

Default Value: ""

This field defines the URL to which the response should be sent.

When using AS2Sender set this field before calling SendCEMRequest. This tells the recipient where to send the response.

When using AS2Receiver query this field to determine the URL where the response should be sent.

Constructors

public CEMDetail();
Public CEMDetail()

Certificate Type

This is the digital certificate being used.

Remarks

This type describes the current digital certificate. The certificate may be a public or private key. The fields are used to identify or select certificates.

Fields

EffectiveDate
string (read-only)

Default Value: ""

This is the date on which this certificate becomes valid. Before this date, it is not valid. The following example illustrates the format of an encoded date:

23-Jan-2000 15:00:00.

Encoded
string

Default Value: ""

This is the certificate (PEM/Base64 encoded). This field is used to assign a specific certificate. The Store and Subject fields also may be used to specify a certificate.

When Encoded is set, a search is initiated in the current Store for the private key of the certificate. If the key is found, Subject is updated to reflect the full subject of the selected certificate; otherwise, Subject is set to an empty string.

EncodedB
byte []

Default Value: ""

This is the certificate (PEM/Base64 encoded). This field is used to assign a specific certificate. The Store and Subject fields also may be used to specify a certificate.

When Encoded is set, a search is initiated in the current Store for the private key of the certificate. If the key is found, Subject is updated to reflect the full subject of the selected certificate; otherwise, Subject is set to an empty string.

ExpirationDate
string (read-only)

Default Value: ""

This is the date the certificate expires. After this date, the certificate will no longer be valid. The following example illustrates the format of an encoded date:

23-Jan-2001 15:00:00.

ExtendedKeyUsage
string

Default Value: ""

This is a comma-delimited list of extended key usage identifiers. These are the same as ASN.1 object identifiers (OIDs).

Fingerprint
string (read-only)

Default Value: ""

This is the hex-encoded, 16-byte MD5 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: bc:2a:72:af:fe:58:17:43:7a:5f:ba:5a:7c:90:f7:02

FingerprintSHA1
string (read-only)

Default Value: ""

This is the hex-encoded, 20-byte SHA-1 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 30:7b:fa:38:65:83:ff:da:b4:4e:07:3f:17:b8:a4:ed:80:be:ff:84

FingerprintSHA256
string (read-only)

Default Value: ""

This is the hex-encoded, 32-byte SHA-256 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 6a:80:5c:33:a9:43:ea:b0:96:12:8a:64:96:30:ef:4a:8a:96:86:ce:f4:c7:be:10:24:8e:2b:60:9e:f3:59:53

Issuer
string (read-only)

Default Value: ""

This is the issuer of the certificate. This field contains a string representation of the name of the issuing authority for the certificate.

PrivateKey
string (read-only)

Default Value: ""

This is the private key of the certificate (if available). The key is provided as PEM/Base64-encoded data.

Note: The PrivateKey may be available but not exportable. In this case, PrivateKey returns an empty string.

PrivateKeyAvailable
bool (read-only)

Default Value: False

This field shows whether a PrivateKey is available for the selected certificate. If PrivateKeyAvailable is True, the certificate may be used for authentication purposes (e.g., server authentication).

PrivateKeyContainer
string (read-only)

Default Value: ""

This is the name of the PrivateKey container for the certificate (if available). This functionality is available only on Windows platforms.

PublicKey
string (read-only)

Default Value: ""

This is the public key of the certificate. The key is provided as PEM/Base64-encoded data.

PublicKeyAlgorithm
string

Default Value: ""

This field contains the textual description of the certificate's public key algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_DH") or an object identifier (OID) string representing the algorithm.

PublicKeyLength
int (read-only)

Default Value: 0

This is the length of the certificate's public key (in bits). Common values are 512, 1024, and 2048.

SerialNumber
string (read-only)

Default Value: ""

This is the serial number of the certificate encoded as a string. The number is encoded as a series of hexadecimal digits, with each pair representing a byte of the serial number.

SignatureAlgorithm
string (read-only)

Default Value: ""

The field contains the text description of the certificate's signature algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_MD5RSA") or an object identifier (OID) string representing the algorithm.

Store
string

Default Value: "MY"

This is the name of the certificate store for the client certificate.

The StoreType field denotes the type of the certificate store specified by Store. If the store is password protected, specify the password in StorePassword.

Store is used in conjunction with the Subject field to specify client certificates. If Store has a value, and Subject or Encoded is set, a search for a certificate is initiated. Please see the Subject field for details.

Designations of certificate stores are platform dependent.

The following designations are the most common User and Machine certificate stores in Windows:

MYA certificate store holding personal certificates with their associated private keys.
CACertifying authority certificates.
ROOTRoot certificates.

When the certificate store type is PFXFile, this property must be set to the name of the file. When the type is PFXBlob, the property must be set to the binary contents of a PFX file (i.e., PKCS#12 certificate store).

StoreB
byte []

Default Value: "MY"

This is the name of the certificate store for the client certificate.

The StoreType field denotes the type of the certificate store specified by Store. If the store is password protected, specify the password in StorePassword.

Store is used in conjunction with the Subject field to specify client certificates. If Store has a value, and Subject or Encoded is set, a search for a certificate is initiated. Please see the Subject field for details.

Designations of certificate stores are platform dependent.

The following designations are the most common User and Machine certificate stores in Windows:

MYA certificate store holding personal certificates with their associated private keys.
CACertifying authority certificates.
ROOTRoot certificates.

When the certificate store type is PFXFile, this property must be set to the name of the file. When the type is PFXBlob, the property must be set to the binary contents of a PFX file (i.e., PKCS#12 certificate store).

StorePassword
string

Default Value: ""

If the type of certificate store requires a password, this property is used to specify the password needed to open the certificate store.

StoreType
CertStoreTypes

Default Value: 0

This is the type of certificate store for this certificate.

The component supports both public and private keys in a variety of formats. When the cstAuto value is used, the component will automatically determine the type. This field can take one of the following values:

0 (cstUser - default)For Windows, this specifies that the certificate store is a certificate store owned by the current user.

Note: This store type is not available in Java.

1 (cstMachine)For Windows, this specifies that the certificate store is a machine store.

Note: This store type is not available in Java.

2 (cstPFXFile)The certificate store is the name of a PFX (PKCS#12) file containing certificates.
3 (cstPFXBlob)The certificate store is a string (binary or Base64-encoded) representing a certificate store in PFX (PKCS#12) format.
4 (cstJKSFile)The certificate store is the name of a Java Key Store (JKS) file containing certificates.

Note: This store type is only available in Java.

5 (cstJKSBlob)The certificate store is a string (binary or Base64-encoded) representing a certificate store in Java Key Store (JKS) format.

Note: this store type is only available in Java.

6 (cstPEMKeyFile)The certificate store is the name of a PEM-encoded file that contains a private key and an optional certificate.
7 (cstPEMKeyBlob)The certificate store is a string (binary or Base64-encoded) that contains a private key and an optional certificate.
8 (cstPublicKeyFile)The certificate store is the name of a file that contains a PEM- or DER-encoded public key certificate.
9 (cstPublicKeyBlob)The certificate store is a string (binary or Base64-encoded) that contains a PEM- or DER-encoded public key certificate.
10 (cstSSHPublicKeyBlob)The certificate store is a string (binary or Base64-encoded) that contains an SSH-style public key.
11 (cstP7BFile)The certificate store is the name of a PKCS#7 file containing certificates.
12 (cstP7BBlob)The certificate store is a string (binary) representing a certificate store in PKCS#7 format.
13 (cstSSHPublicKeyFile)The certificate store is the name of a file that contains an SSH-style public key.
14 (cstPPKFile)The certificate store is the name of a file that contains a PPK (PuTTY Private Key).
15 (cstPPKBlob)The certificate store is a string (binary) that contains a PPK (PuTTY Private Key).
16 (cstXMLFile)The certificate store is the name of a file that contains a certificate in XML format.
17 (cstXMLBlob)The certificate store is a string that contains a certificate in XML format.
18 (cstJWKFile)The certificate store is the name of a file that contains a JWK (JSON Web Key).
19 (cstJWKBlob)The certificate store is a string that contains a JWK (JSON Web Key).
21 (cstBCFKSFile)The certificate store is the name of a file that contains a BCFKS (Bouncy Castle FIPS Key Store).

Note: This store type is only available in Java and .NET.

22 (cstBCFKSBlob)The certificate store is a string (binary or Base64-encoded) representing a certificate store in BCFKS (Bouncy Castle FIPS Key Store) format.

Note: This store type is only available in Java and .NET.

23 (cstPKCS11)The certificate is present on a physical security key accessible via a PKCS#11 interface.

To use a security key, the necessary data must first be collected using the CertMgr component. The ListStoreCertificates method may be called after setting CertStoreType to cstPKCS11, CertStorePassword to the PIN, and CertStore to the full path of the PKCS#11 DLL. The certificate information returned in the CertList event's CertEncoded parameter may be saved for later use.

When using a certificate, pass the previously saved security key information as the Store and set StorePassword to the PIN.

Code Example. SSH Authentication with Security Key: certmgr.CertStoreType = CertStoreTypes.cstPKCS11; certmgr.OnCertList += (s, e) => { secKeyBlob = e.CertEncoded; }; certmgr.CertStore = @"C:\Program Files\OpenSC Project\OpenSC\pkcs11\opensc-pkcs11.dll"; certmgr.CertStorePassword = "123456"; //PIN certmgr.ListStoreCertificates(); sftp.SSHCert = new Certificate(CertStoreTypes.cstPKCS11, secKeyBlob, "123456", "*"); sftp.SSHUser = "test"; sftp.SSHLogon("myhost", 22);

99 (cstAuto)The store type is automatically detected from the input data. This setting may be used with both public and private keys and can detect any of the supported formats automatically.

Subject
string

Default Value: ""

This is the subject of the certificate used for client authentication.

This field will be populated with the full subject of the loaded certificate. When loading a certificate the subject is used to locate the certificate in the store.

If an exact match is not found, the store is searched for subjects containing the value of the property.

If a match is still not found, the property is set to an empty string, and no certificate is selected.

The special value "*" picks a random certificate in the certificate store.

The certificate subject is a comma-separated list of distinguished name fields and values. For instance, "CN=www.server.com, OU=test, C=US, E=support@nsoftware.com". Common fields and their meanings are as follows:

FieldMeaning
CNCommon Name. This is commonly a hostname like www.server.com.
OOrganization
OUOrganizational Unit
LLocality
SState
CCountry
EEmail Address

If a field value contains a comma, it must be quoted.

SubjectAltNames
string (read-only)

Default Value: ""

This field contains comma-separated lists of alternative subject names for the certificate.

ThumbprintMD5
string (read-only)

Default Value: ""

This field contains the MD5 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

ThumbprintSHA1
string (read-only)

Default Value: ""

This field contains the SHA-1 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

ThumbprintSHA256
string (read-only)

Default Value: ""

This field contains the SHA-256 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

Usage
string

Default Value: ""

This field contains the text description of UsageFlags.

This value will be of one or more of the following strings and will be separated by commas:

  • Digital Signatures
  • Key Authentication
  • Key Encryption
  • Data Encryption
  • Key Agreement
  • Certificate Signing
  • Key Signing

If the provider is OpenSSL, the value is a comma-separated list of X.509 certificate extension names.

UsageFlags
int

Default Value: 0

This field contains the flags that show intended use for the certificate. The value of UsageFlags is a combination of the following flags:

0x80Digital Signatures
0x40Key Authentication (Non-Repudiation)
0x20Key Encryption
0x10Data Encryption
0x08Key Agreement
0x04Certificate Signing
0x02Key Signing

Please see the Usage field for a text representation of UsageFlags.

This functionality currently is not available when the provider is OpenSSL.

Version
string (read-only)

Default Value: ""

This field contains the certificate's version number. The possible values are the strings "V1", "V2", and "V3".

Constructors

public Certificate();
Public Certificate()

Creates a Certificate instance whose properties can be set. This is useful for use with CERTMGR when generating new certificates.

public Certificate(string certificateFile);
Public Certificate(ByVal CertificateFile As String)

Opens CertificateFile and reads out the contents as an X.509 public key.

public Certificate(byte[] certificateData);
Public Certificate(ByVal CertificateData As Byte())

Parses CertificateData as an X.509 public key.

public Certificate(CertStoreTypes certStoreType, string store, string storePassword, string subject);
Public Certificate(ByVal CertStoreType As CertStoreTypes, ByVal Store As String, ByVal StorePassword As String, ByVal Subject As String)

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a file containing the certificate store. StorePassword is the password used to protect the store. After the store has been successfully opened, the component will attempt to find the certificate identified by Subject . This can be either a complete or a substring match of the X.509 certificate's subject Distinguished Name (DN).

public Certificate(CertStoreTypes certStoreType, string store, string storePassword, string subject, string configurationString);
Public Certificate(ByVal CertStoreType As CertStoreTypes, ByVal Store As String, ByVal StorePassword As String, ByVal Subject As String, ByVal ConfigurationString As String)

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a file containing the certificate store. StorePassword is the password used to protect the store. ConfigurationString is a newline separated list of name-value pairs that may be used to modify the default behavior. Possible values include "PersistPFXKey", which shows whether or not the PFX key is persisted after performing operations with the private key. This correlates to the PKCS12_NO_PERSIST_KEY CryptoAPI option. The default value is True (the key is persisted). "Thumbprint" - an MD5, SHA-1, or SHA-256 thumbprint of the certificate to load. When specified, this value is used to select the certificate in the store. This is applicable to cstUser, cstMachine, cstPublicKeyFile, and cstPFXFile store types. "UseInternalSecurityAPI" shows whether the platform (default) or the internal security API is used when performing certificate-related operations. After the store has been successfully opened, the component will attempt to find the certificate identified by Subject . This can be either a complete or a substring match of the X.509 certificate's subject Distinguished Name (DN).

public Certificate(CertStoreTypes certStoreType, string store, string storePassword, byte[] encoded);
Public Certificate(ByVal CertStoreType As CertStoreTypes, ByVal Store As String, ByVal StorePassword As String, ByVal Encoded As Byte())

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a file containing the certificate store. StorePassword is the password used to protect the store. After the store has been successfully opened, the component will load Encoded as an X.509 certificate and search the opened store for a corresponding private key.

public Certificate(CertStoreTypes certStoreType, byte[] storeBlob, string storePassword, string subject);
Public Certificate(ByVal CertStoreType As CertStoreTypes, ByVal StoreBlob As Byte(), ByVal StorePassword As String, ByVal Subject As String)

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. StoreBlob is a string (binary- or Base64-encoded) containing the certificate data. StorePassword is the password used to protect the store. After the store has been successfully opened, the component will attempt to find the certificate identified by Subject . This can be either a complete or a substring match of the X.509 certificate's subject Distinguished Name (DN).

public Certificate(CertStoreTypes certStoreType, byte[] storeBlob, string storePassword, string subject, string configurationString);
Public Certificate(ByVal CertStoreType As CertStoreTypes, ByVal StoreBlob As Byte(), ByVal StorePassword As String, ByVal Subject As String, ByVal ConfigurationString As String)

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. StoreBlob is a string (binary- or Base64-encoded) containing the certificate data. StorePassword is the password used to protect the store. After the store has been successfully opened, the component will attempt to find the certificate identified by Subject . This can be either a complete or a substring match of the X.509 certificate's subject Distinguished Name (DN).

public Certificate(CertStoreTypes certStoreType, byte[] storeBlob, string storePassword, byte[] encoded);
Public Certificate(ByVal CertStoreType As CertStoreTypes, ByVal StoreBlob As Byte(), ByVal StorePassword As String, ByVal Encoded As Byte())

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a string (binary- or Base64-encoded) containing the certificate store. StorePassword is the password used to protect the store. After the store has been successfully opened, the component will load Encoded as an X.509 certificate and search the opened store for a corresponding private key.

EDIAttachment Type

This describes the file being attached.

Remarks

Information about the file's location that is being attached to the message is contained here.

Fields

ContentType
string

Default Value: ""

The MIME content-type of this EDIAttachment.

Data
string

Default Value: ""

This field contains the attachment data.

In a receiver, the component decodes the attachment to the Data field when Data's value is first queried. This field will contain the full decrypted text of the attachment.

DataB
byte []

Default Value: ""

This field contains the attachment data.

In a receiver, the component decodes the attachment to the Data field when Data's value is first queried. This field will contain the full decrypted text of the attachment.

Filename
string

Default Value: ""

The file name of the attachment. If IncomingDirectory has been specified, the attachment will be written to the specified directory and the name will be provided by this field. Otherwise, this will contain the name of the attachment as described in the Headers.

Headers
string

Default Value: ""

The component fills out Headers each time any of the other fields for that EDIAttachment are changed. If additional headers are needed they should be appended after all the other fields for that EDIAttachment are set.

InputStream
System.IO.Stream

Default Value: ""

If InputStream is specified, the data from the stream specified will be used for the EDI attachment.

Name
string

Default Value: ""

Name is the final name to be associated with the contents of either the Data or Filename fields. This corresponds to the filename attribute of the Content-Disposition header for this attachment.

OutputStream
System.IO.Stream

Default Value: ""

The component decodes the attachment of Message when This field's value is first set, and writes the decoded attachment to the stream.

Note: It is recommended to use the SetAttachmentOutputStream method instead of setting this field.

Constructors

public EDIAttachment();
Public EDIAttachment()
public EDIAttachment(string filename);
Public EDIAttachment(ByVal Filename As String)
public EDIAttachment(string filename, string contentType);
Public EDIAttachment(ByVal Filename As String, ByVal ContentType As String)
public EDIAttachment(string filename, string contentType, string headers);
Public EDIAttachment(ByVal Filename As String, ByVal ContentType As String, ByVal Headers As String)

EDIData Type

The EDI payload of the AS2 message.

Remarks

The EDI payload of the AS2 message.

Fields

Data
string

Default Value: ""

This field contains the EDI payload of the transmission.

In a receiver, this field will only be populated if IncomingDirectory and OutputStream have not been specified and ParseRequest finishes without an error, setting ScanResult to 0. If so, Data will contain the full decrypted text of the EDI message.

DataB
byte []

Default Value: ""

This field contains the EDI payload of the transmission.

In a receiver, this field will only be populated if IncomingDirectory and OutputStream have not been specified and ParseRequest finishes without an error, setting ScanResult to 0. If so, Data will contain the full decrypted text of the EDI message.

EDIType
string

Default Value: ""

The Content-Type of the EDI message. Sample values might be "application/edi-x12", "application/edifact" or "application/xml".

Filename
string

Default Value: ""

In a sender, if Filename is specified, the file specified will be used for the EDI payload of the transmission. Name will be populated with the name of the file.

In a receiver, when IncomingDirectory is set, this will be populated with the absolute path of the file which contains the processed message contents.

Note: When OutputStream is set, the data will be written to the stream and this field will not be populated.

InputStream
System.IO.Stream

Default Value: ""

In a sender, if InputStream is specified, the data from the specified stream will be used for the EDI payload of the transmission.

Name
string

Default Value: "rfc1767.edi"

Name is the final name to be associated with the contents of either the Data or FileName fields. This corresponds to the filename attribute of the Content-Disposition header for the EDI payload.

When constructing EDI data to be sent, Name will be set to the same value as FileName, but can be overridden after setting FileName to indicate that another name should be used in the outbound request's Content-Disposition MIME header.

When receiving EDI data, Name will be read out of the "filename" attribute of the inbound request's Content-Disposition MIME header.

OutputStream
System.IO.Stream

Default Value: ""

In a receiver, if this field is set, the EDI payload will be written to this stream if ParseRequest finishes without an error, setting ScanResult to 0. If so, the specified stream will contain the full decrypted text of the EDI message.

NOTE: When OutputStream is used and the underlying data contains attachments, the attachments will not be decoded to the output stream. Attachments are accessible via the Attachments collection.

Constructors

public EDIData();
Public EDIData()
public EDIData(byte[] data, string EDIType);
Public EDIData(ByVal Data As Byte(), ByVal EDIType As String)
public EDIData(string filename, string EDIType);
Public EDIData(ByVal Filename As String, ByVal EDIType As String)

Firewall Type

The firewall the component will connect through.

Remarks

When connecting through a firewall, this type is used to specify different properties of the firewall, such as the firewall Host and the FirewallType.

Fields

AutoDetect
bool

Default Value: False

This field tells the component whether or not to automatically detect and use firewall system settings, if available.

FirewallType
FirewallTypes

Default Value: 0

This field determines the type of firewall to connect through. The applicable values are as follows:

fwNone (0)No firewall (default setting).
fwTunnel (1)Connect through a tunneling proxy. Port is set to 80.
fwSOCKS4 (2)Connect through a SOCKS4 Proxy. Port is set to 1080.
fwSOCKS5 (3)Connect through a SOCKS5 Proxy. Port is set to 1080.
fwSOCKS4A (10)Connect through a SOCKS4A Proxy. Port is set to 1080.

Host
string

Default Value: ""

This field contains the name or IP address of firewall (optional). If a Host is given, the requested connections will be authenticated through the specified firewall when connecting.

If this field is set to a Domain Name, a DNS request is initiated. Upon successful termination of the request, this field is set to the corresponding address. If the search is not successful, the component throws an exception.

Password
string

Default Value: ""

This field contains a password if authentication is to be used when connecting through the firewall. If Host is specified, the User and Password fields are used to connect and authenticate to the given firewall. If the authentication fails, the component throws an exception.

Port
int

Default Value: 0

This field contains the transmission control protocol (TCP) port for the firewall Host. See the description of the Host field for details.

Note: This field is set automatically when FirewallType is set to a valid value. See the description of the FirewallType field for details.

User
string

Default Value: ""

This field contains a user name if authentication is to be used connecting through a firewall. If the Host is specified, this field and Password fields are used to connect and authenticate to the given Firewall. If the authentication fails, the component throws an exception.

Constructors

public Firewall();
Public Firewall()

HTTPCookie Type

An HTTP cookie can be either sent to or received from the server.

Remarks

An HTTP cookie can store the cookies that are to be sent to the server. It also may store the cookies sent by the server.

Cookies that are to be sent to the server must have the Name and Value fields supplied before submitting the URL. When the SetCookie event is fired, however, all of the fields of an HTTPCookie are filled out accordingly.

Fields

Domain
string (read-only)

Default Value: ""

This is the domain of a received cookie. This field contains a domain name to limit the cookie to (if provided by the server). If the server does not provide a domain name, this field will contain an empty string. The convention in this case is to use the server name specified by URLServer as the cookie domain.

Expiration
string (read-only)

Default Value: ""

This field contains an expiration time for the cookie (if provided by the server). The time format used is "Weekday, DD-Mon-YY HH:MM:SS GMT". If the server does not provide an expiration time, this field will contain an empty string. The convention is to drop the cookie at the end of the session.

Name
string

Default Value: ""

This field, contains the name of the cookie.

This field, along with Value, stores the cookie that is to be sent to the server. The SetCookie event displays the cookies sent by the server and their properties.

Path
string (read-only)

Default Value: ""

This field contains a path name to limit the cookie to (if provided by the server). If the server does not provide a cookie path, the path field will be an empty string. The convention in this case is to use the path specified by URLPath as the cookie path.

Secure
bool (read-only)

Default Value: False

This field contains the security flag of the received cookie. This field specifies whether the cookie is secure. If the value of this field is True, the cookie value must be submitted only through a secure (HTTPS) connection.

Value
string

Default Value: ""

This field contains the value of the cookie. A corresponding value is associated with the cookie specified by Name. This property holds that value.

The SetCookie event provides the cookies set by the server.

Constructors

public HTTPCookie();
Public HTTPCookie()
public HTTPCookie(string name, string value);
Public HTTPCookie(ByVal Name As String, ByVal Value As String)

MDNReceipt Type

The complete MDN Receipt returned by the receiver.

Remarks

The complete MDN Receipt contains the Message Disposition Notification (MDN) and an optional signature.

Fields

Content
string

Default Value: ""

This contains the entire content of the MDN Receipt. This is a multipart/report entity consisting of a machine readable MDN (Message Disposition Notification) and a human readable Message, which itself may be embedded in a multipart/signed entity if requested by the AS2 sender.

ContentB
byte []

Default Value: ""

This contains the entire content of the MDN Receipt. This is a multipart/report entity consisting of a machine readable MDN (Message Disposition Notification) and a human readable Message, which itself may be embedded in a multipart/signed entity if requested by the AS2 sender.

HeaderCount
int (read-only)

Default Value: 0

The number of headers in the MDN.

HeaderField
string (read-only)

Default Value: ""

The field name of the MDN header currently selected by HeaderIndex.

HeaderIndex
int

Default Value: 0

Which MDN header is currently selected to populate HeaderField and HeaderValue.

Valid values are 0 to HeaderCount - 1.

Headers
string

Default Value: ""

Headers contains all of the headers of the AS2 MDN Receipt as a single string. This will include headers such as AS2-From, AS2-To, Date, Content-Type, etc. In an AS2Sender, these will also contain the transport headers of the MDN Receipt (HTTP or SMTP headers, depending on the delivery option).

You can also use HeaderCount, HeaderIndex, HeaderField, and HeaderValue to easily iterate through each individual header.

HeaderValue
string (read-only)

Default Value: ""

The value of the MDN header currently selected by HeaderIndex.

MDN
string (read-only)

Default Value: ""

MDN will contain the entire machine readable text of the Message Disposition Notification in the receipt. It will report either success or failure depending on the processing status of the receiver. In either case, it will be RFC-compliant.

Message
string (read-only)

Default Value: ""

The human-readable portion of the MDN receipt.

The human-readable portion of the MDN receipt that indicates the status of the message processing. This can be used to provide the user with a helpful message in the event that an error is encountered.

MICValue
string (read-only)

Default Value: ""

The Message Integrity Check(s) (one-way hash) of the original EDI message.

An MDN Receipt contains a MIC calculated over the EDI message that the receipt is in response to, to be matched on the sender side against a saved value for the original request to ensure that the integrity of the data that the receiver reports is preserved. When a signed receipt is requested, the MIC is be calculated using the algorithm used on the incoming message's signature, or SHA-1 if the incoming message is not signed.

The MIC will be base64 encoded and reported with the algorithm name as specified in RFC 3335; e.g., "w7AguNJEmhF/qIjJw6LnnA==, md5".

SigningProtocol
string (read-only)

Default Value: ""

This field contains the MIME type of the signature used, if any (i.e., "application/pkcs7-signature"), to create this MDNReceipt. It will contain an empty string if the receipt is unsigned.

Constructors

public MDNReceipt();
Public MDNReceipt()
public MDNReceipt(string headers, byte[] content);
Public MDNReceipt(ByVal Headers As String, ByVal Content As Byte())

Proxy Type

The proxy the component will connect to.

Remarks

When connecting through a proxy, this type is used to specify different properties of the proxy, such as the Server and the AuthScheme.

Fields

AuthScheme
ProxyAuthSchemes

Default Value: 0

This field is used to tell the component which type of authorization to perform when connecting to the proxy. This is used only when the User and Password fields are set.

AuthScheme should be set to authNone (3) when no authentication is expected.

By default, AuthScheme is authBasic (0), and if the User and Password fields are set, the component will attempt basic authentication.

If AuthScheme is set to authDigest (1), digest authentication will be attempted instead.

If AuthScheme is set to authProprietary (2), then the authorization token will not be generated by the component. Look at the configuration file for the component being used to find more information about manually setting this token.

If AuthScheme is set to authNtlm (4), NTLM authentication will be used.

For security reasons, setting this field will clear the values of User and Password.

AutoDetect
bool

Default Value: False

This field tells the component whether or not to automatically detect and use proxy system settings, if available. The default value is false.

Password
string

Default Value: ""

This field contains a password if authentication is to be used for the proxy.

If AuthScheme is set to Basic Authentication, the User and Password are Base64 encoded and the proxy authentication token will be generated in the form Basic [encoded-user-password].

If AuthScheme is set to Digest Authentication, the User and Password fields are used to respond to the Digest Authentication challenge from the server.

If AuthScheme is set to NTLM Authentication, the User and Password fields are used to authenticate through NTLM negotiation.

Port
int

Default Value: 80

This field contains the Transmission Control Protocol (TCP) port for the proxy Server (default 80). See the description of the Server field for details.

Server
string

Default Value: ""

If a proxy Server is given, then the HTTP request is sent to the proxy instead of the server otherwise specified.

If the Server field is set to a domain name, a DNS request is initiated. Upon successful termination of the request, the Server field is set to the corresponding address. If the search is not successful, an error is returned.

SSL
ProxySSLTypes

Default Value: 0

This field determines when to use a Secure Sockets Layer (SSL) for the connection to the proxy. The applicable values are as follows:

psAutomatic (0)Default setting. If the URL is an https URL, the component will use the psTunnel option. If the URL is an http URL, the component will use the psNever option.
psAlways (1)The connection is always SSL enabled.
psNever (2)The connection is not SSL enabled.
psTunnel (3)The connection is made through a tunneling (HTTP) proxy.

User
string

Default Value: ""

This field contains a username if authentication is to be used for the proxy.

If AuthScheme is set to Basic Authentication, the User and Password fields are Base64 encoded and the proxy authentication token will be generated in the form Basic [encoded-user-password].

If AuthScheme is set to Digest Authentication, the User and Password fields are used to respond to the Digest Authentication challenge from the server.

If AuthScheme is set to NTLM Authentication, the User and Password fields are used to authenticate through NTLM negotiation.

Constructors

public Proxy();
Public Proxy()
public Proxy(string server, int port);
Public Proxy(ByVal Server As String, ByVal Port As Integer)
public Proxy(string server, int port, string user, string password);
Public Proxy(ByVal Server As String, ByVal Port As Integer, ByVal User As String, ByVal Password As String)

Config Settings (AS2Sender Component)

The component accepts one or more of the following configuration settings. Configuration settings are similar in functionality to properties, but they are rarely used. In order to avoid "polluting" the property namespace of the component, access to these internal properties is provided through the Config method.

AS2Sender Config Settings

AllowMDNWarnings:   Whether to fail on MDN warnings.

When processing MDNs this setting determines if the component throws an exception when a MDN warning is processed. By default this value is False and MDN warnings other than duplicate files warnings will result in an exception. If set to True all MDN warnings will be allowed and processing will continue as normal. Check MDNDisposition to process the warning manually in this case.

Authorization:   The Authorization string to be sent to the server.

If the Authorization setting contains a non-empty string, an Authorization HTTP request header is added to the request. This header conveys Authorization information to the server.

This setting is provided so that the component can be extended with other security schemes in addition to the authorization schemes already implemented by the component.

The AuthScheme; setting defines the authentication scheme used. In the case of HTTP Basic Authentication (default), every time User and Password are set, they are Base64 encoded, and the result is put in the Authorization setting in the form "Basic [encoded-user-password]".

AuthScheme:   The authorization scheme to be used when server authorization is to be performed.

Use the AuthScheme property to tell the component which type of authorization to perform when the User and Password properties are set. Possible values are:

0 (default)Basic
1Digest
2Proprietary
3None
4NTLM
5Negotiate
6OAuth
By default, AuthScheme is Basic (0), and if the User and Password configuration settings are set, the component will attempt basic authentication. If AuthScheme is set to Digest (1), digest authentication will be attempted instead.

For security reasons, setting this value will clear the values of User and Password.

CompressFirst:   Whether compression occurs before signing a message.

This setting determines the order of actions taken on the message. You will only need to change this setting if your partner requires a specific order. If True, the message will be compressed, signed, and then encrypted. If False (default), the message will be signed, compressed, and then encrypted. Either order is acceptable according to the specifications.

EncodeToTempDir:   Whether to use temporary files when creating messages.

This setting determines if temporary files are used when creating messages. By default this value is not set and messages are created in memory before posting. When working with very large files this can cause substantial memory usage. To avoid memory overhead when working with large files set this to a relative or absolute path to a directory on disk. When Post is called the component will create a file in the specified directory during processing.

IgnoreLoggingErrors:   Whether to ignore errors that occur when writing to the log.

When this setting is enabled (default False), any errors that occur while writing to log files will be ignored, and no exception will be thrown. Note that this may cause logs to be incomplete or missing without any indication that an issue occurred.

IncludeHeaders:   Whether headers are included when posting to a file.

This setting determines if headers are included in the file when using PostToFile. By default this value is true. When set to False headers are not included in the content written to the file. When set to False this also allows data to be streamed directly to the file specified by PostToFile without any substantial memory overhead or the use of EncodeToTempDir. After posting to a file check the MessageHeaders to obtain the headers. This setting should only be used when PostToFile is set.

LogDebug:   Whether to log debug data.

This setting specifies whether to log debug data. When set to True the component will create additional files in the LogDirectory. The default value is False.

When sending, files with extensions ".input", ".sign", ".compress", and ".encrypt" may be created. When receiving, files with extensions ".input", ".verify", ".decompress", and ".decrypt" may be created.

LogFilename:   The base name of the log file.

If set, this will be used as for the filename of the log file.

Note that only the base name should be specified as the component will append the appropriate file extension.

LogOptions:   The information to be written to log files.

When LogDirectory is set, several pieces of information are written to log files in the specified directory. Set LogOptions to one or more of the following values to control what information is written to file. When specifying multiple values, include them in the same string (i.e. "LogOptions=Status, Response, Payload"):

StatusContains information on applied security options and pass/fail status of transmission
RequestContains outgoing transmission, with applied security options
PayloadContains log of unsecured payload prior to transmission
ResponseFor synchronous requests or asynchronous receipts verified with VerifyReceipt, contains MDN receipt, if sent. For asynchronous requests, contains server acknowledgement.
ErrorsA separate file with a .err extension is written when an error is encountered.
AllAll of the above

MDNDisposition:   Returns the Disposition header of the MDN.

This setting returns the Disposition header value from the MDN.

MessageHeaders:   Returns the headers of the message.

This setting returns the headers of the generated message when IncludeHeaders is False and PostToFile is set. It should not be used in any other cases.

NormalizeMIC:   Whether to normalize line endings before calculating the MIC.

This setting determines whether to normalize line endings before signature verification.

In most cases the signature is verified by calculating a Message Integrity Check (MIC) over the exact data that is received. In some cases other software such as Mendelson AS2 may calculate signatures over a version of the data with normalized line endings. During processing attempts to verify a signature that was created in this manner may lead to one of the following errors:

  • Unable to verify content integrity: Message digest mismatch in signature.
  • The receipt signature could not be verified: Message digest mismatch in signature.

If one of the errors above is encountered and the received data is expected to be otherwise correct setting this setting to True may resolve the issue by normalizing line endings before verifying the signature.

Note: This should only be set to True if there is a specific reason to do so.

OAEPMGF1HashAlgorithm:   The MGF1 hash algorithm used when encrypting a key.

When UseOAEP is True, this algorithm specifies the MGF1 hash algorithm used for the encryption key by RSA OAEP. Possible values are:

  • "SHA1"
  • "SHA224"
  • "SHA256" (default)
  • "SHA384"
  • "SHA512"

Note: An empty string value indicates that the algorithm specified by OAEPRSAHashAlgorithm is used as the RSA hash algorithm as well.

OAEPParams:   The hex encoded OAEP parameters to be used when encrypting a key.

This setting is optional and should only be specified if OAEP parameters need to be explicitly set. The value specified should be a hex string. By default this setting is unspecified.

OAEPRSAHashAlgorithm:   The RSA hash algorithm used when encrypting a key.

When UseOAEP is True, this algorithm specifies the RSA hash algorithm used for the encryption key. This may differ from the hash algorithm used to sign the AS4 message content. Possible values are:

  • "SHA1"
  • "SHA224"
  • "SHA256" (default)
  • "SHA384"
  • "SHA512"
Password:   A password if authentication is to be used.

If AuthScheme is set to Basic, the User and Password are Base64 encoded and the result is put in the Authorization configuration setting in the form "Basic [encoded-user-password]".

If AuthScheme is set to Digest, the User and Password properties are used to respond to the HTTP Digest Authentication challenge from the server.

The User and Password properties must be set only after the URL property is set. When the URL property is set, for security reasons, User and Password are immediately cleared.

PostToFile:   Creates the message on disk.

This setting allows for the message to be created on disk without actually being sent. This is useful in certain situations to prepare the message where it is sent by a different transport mechanism at a later time. This should be set to a relative or absolute file path including the filename. When this is set the component will immediately start processing the message and writing to the specified file.

RequiredSignatureAlgorithms:   Specifies a list of acceptable signature algorithms.

This setting specifies a comma separated list of allowed signature algorithms used in messages verified by the component. By default the setting is empty and any signature algorithm is supported. To restrict the algorithms to one or more values set this setting to a comma separated list. For instance sha1,sha256.

User:   A user name if authentication is to be used.

If AuthScheme is set to Basic, the User and Password are Base64 encoded and the result is put in the Authorization configuration setting in the form "Basic [encoded-user-password]".

If AuthScheme is set to Digest, the User and Password properties are used to respond to the HTTP Digest Authentication challenge from the server.

The User and Password properties must be set only after the URL property is set. When the URL property is set, for security reasons, User and Password are immediately cleared.

HTTP Config Settings

AcceptEncoding:   Used to tell the server which types of content encodings the client supports.

When AllowHTTPCompression is True, the component adds an Accept-Encoding header to the request being sent to the server. By default, this header's value is "gzip, deflate". This configuration setting allows you to change the value of the Accept-Encoding header. Note: The component only supports gzip and deflate decompression algorithms.

AllowHTTPCompression:   This property enables HTTP compression for receiving data.

This configuration setting enables HTTP compression for receiving data. When set to True (default), the component will accept compressed data. It then will uncompress the data it has received. The component will handle data compressed by both gzip and deflate compression algorithms.

When True, the component adds an Accept-Encoding header to the outgoing request. The value for this header can be controlled by the AcceptEncoding configuration setting. The default value for this header is "gzip, deflate".

The default value is True.

AllowHTTPFallback:   Whether HTTP/2 connections are permitted to fallback to HTTP/1.1.

This configuration setting controls whether HTTP/2 connections are permitted to fall back to HTTP/1.1 when the server does not support HTTP/2. This setting is applicable only when HTTPVersion is set to "2.0".

If set to True (default), the component will automatically use HTTP/1.1 if the server does not support HTTP/2. If set to False, the component throws an exception if the server does not support HTTP/2.

The default value is True.

AllowNTLMFallback:   Whether to allow fallback from Negotiate to NTLM when authenticating.

This configuration setting applies only when AuthScheme is set to Negotiate. If set to True, the component will automatically use New Technology LAN Manager (NTLM) if the server does not support Negotiate authentication. Note: The server must indicate that it supports NTLM authentication through the WWW-Authenticate header for the fallback from Negotiate to NTLM to take place. The default value is False.

Append:   Whether to append data to LocalFile.

This configuration setting determines whether data will be appended when writing to LocalFile. When set to True, downloaded data will be appended to LocalFile. This may be used in conjunction with Range to resume a failed download. This is applicable only when LocalFile is set. The default value is False.

Authorization:   The Authorization string to be sent to the server.

If the Authorization property contains a nonempty string, an Authorization HTTP request header is added to the request. This header conveys Authorization information to the server.

This property is provided so that the HTTP component can be extended with other security schemes in addition to the authorization schemes already implemented by the component.

The AuthScheme property defines the authentication scheme used. In the case of HTTP Basic Authentication (default), every time User and Password are set, they are Base64 encoded, and the result is put in the Authorization property in the form "Basic [encoded-user-password]".

BytesTransferred:   Contains the number of bytes transferred in the response data.

This configuration setting returns the raw number of bytes from the HTTP response data, before the component processes the data, whether it is chunked or compressed. This returns the same value as the Transfer event, by BytesTransferred.

ChunkSize:   Specifies the chunk size in bytes when using chunked encoding.

This is applicable only when UseChunkedEncoding is True. This setting specifies the chunk size in bytes to be used when posting data. The default value is 16384.

CompressHTTPRequest:   Set to true to compress the body of a PUT or POST request.

If set to True, the body of a PUT or POST request will be compressed into gzip format before sending the request. The "Content-Encoding" header is also added to the outgoing request.

The default value is False.

EncodeURL:   If set to True the URL will be encoded by the component.

If set to True, the URL passed to the component will be URL encoded. The default value is False.

FollowRedirects:   Determines what happens when the server issues a redirect.

This option determines what happens when the server issues a redirect. Normally, the component returns an error if the server responds with an "Object Moved" message. If this property is set to 1 (always), the new URL for the object is retrieved automatically every time.

If this property is set to 2 (Same Scheme), the new URL is retrieved automatically only if the URL Scheme is the same; otherwise, the component throws an exception.

Note: Following the HTTP specification, unless this option is set to 1 (Always), automatic redirects will be performed only for GET or HEAD requests. Other methods potentially could change the conditions of the initial request and create security vulnerabilities.

Furthermore, if either the new URL server or port are different from the existing one, User and Password are also reset to empty, unless this property is set to 1 (Always), in which case the same credentials are used to connect to the new server.

A Redirect event is fired for every URL the product is redirected to. In the case of automatic redirections, the Redirect event is a good place to set properties related to the new connection (e.g., new authentication parameters).

The default value is 0 (Never). In this case, redirects are never followed, and the component throws an exception instead.

Following are the valid options:

  • 0 - Never
  • 1 - Always
  • 2 - Same Scheme

GetOn302Redirect:   If set to True the component will perform a GET on the new location.

The default value is False. If set to True, the component will perform a GET on the new location. Otherwise, it will use the same HTTP method again.

HTTP2HeadersWithoutIndexing:   HTTP2 headers that should not update the dynamic header table with incremental indexing.

HTTP/2 servers maintain a dynamic table of headers and values seen over the course of a connection. Typically, these headers are inserted into the table through incremental indexing (also known as HPACK, defined in RFC 7541). To tell the component not to use incremental indexing for certain headers, and thus not update the dynamic table, set this configuration option to a comma-delimited list of the header names.

HTTPVersion:   The version of HTTP used by the component.

This property specifies the HTTP version used by the component. Possible values are as follows:

  • "1.0"
  • "1.1" (default)
  • "2.0"
  • "3.0"

When using HTTP/2 ("2.0"), additional restrictions apply. Please see the following notes for details.

HTTP/2 Notes

When using HTTP/2, a secure Secure Sockets Layer/Transport Layer Security (TLS/SSL) connection is required. Attempting to use a plaintext URL with HTTP/2 will result in an error.

If the server does not support HTTP/2, the component will automatically use HTTP/1.1 instead. This is done to provide compatibility without the need for any additional settings. To see which version was used, check NegotiatedHTTPVersion after calling a method. The AllowHTTPFallback setting controls whether this behavior is allowed (default) or disallowed.

HTTP/2 is supported on all versions of Windows. If the Windows version is an earlier version than Windows 8.1/Windows Server 2012 R2, the internal security implementation will be used. If the Windows version is Window 8.1/Windows Server 2012 R2 or later, the system security libraries will be used by default.

HTTP/3 Notes

HTTP/3 is supported only in .NET and Java.

When using HTTP/3, a secure (TLS/SSL) connection is required. Attempting to use a plaintext URL with HTTP/3 will result in an error.

IfModifiedSince:   A date determining the maximum age of the desired document.

If this setting contains a nonempty string, an If-Modified-Since HTTP header is added to the request. The value of this header is used to make the HTTP request conditional: if the requested documented has not been modified since the time specified in the field, a copy of the document will not be returned from the server; instead, a 304 (not modified) response will be returned by the server and the component throws an exception

The format of the date value for IfModifiedSince is detailed in the HTTP specs. For example: Sat, 29 Oct 2017 19:43:31 GMT.

KeepAlive:   Determines whether the HTTP connection is closed after completion of the request.

If true, the component will not send the Connection: Close header. The absence of the Connection header indicates to the server that HTTP persistent connections should be used if supported. Note: Not all servers support persistent connections. If false, the connection will be closed immediately after the server response is received.

The default value for KeepAlive is false.

KerberosSPN:   The Service Principal Name for the Kerberos Domain Controller.

If the Service Principal Name on the Kerberos Domain Controller is not the same as the URL that you are authenticating to, the Service Principal Name should be set here.

LogLevel:   The level of detail that is logged.

This configuration setting controls the level of detail that is logged through the Log event. Possible values are as follows:

0 (None) No events are logged.
1 (Info - default) Informational events are logged.
2 (Verbose) Detailed data are logged.
3 (Debug) Debug data are logged.

The value 1 (Info) logs basic information, including the URL, HTTP version, and status details.

The value 2 (Verbose) logs additional information about the request and response.

The value 3 (Debug) logs the headers and body for both the request and response, as well as additional debug information (if any).

MaxHeaders:   Instructs component to save the amount of headers specified that are returned by the server after a Header event has been fired.

This configuration setting should be set when the TransferredHeaders collection is to be populated when a Header event has been fired. This value represents the number of headers that are to be saved in the collection.

To save all items to the collection, set this configuration setting to -1. If no items are wanted, set this to 0, which will not save any items to the collection. The default for this configuration setting is -1, so all items will be included in the collection.

MaxHTTPCookies:   Instructs component to save the amount of cookies specified that are returned by the server when a SetCookie event is fired.

This configuration setting should be set when populating the Cookies collection as a result of an HTTP request. This value represents the number of cookies that are to be saved in the collection.

To save all items to the collection, set this configuration setting to -1. If no items are wanted, set this to 0, which will not save any items to the collection. The default for this configuration setting is -1, so all items will be included in the collection.

MaxRedirectAttempts:   Limits the number of redirects that are followed in a request.

When FollowRedirects is set to any value other than frNever, the component will follow redirects until this maximum number of redirect attempts are made. The default value is 20.

NegotiatedHTTPVersion:   The negotiated HTTP version.

This configuration setting may be queried after the request is complete to indicate the HTTP version used. When HTTPVersion is set to "2.0" (if the server does not support "2.0"), then the component will fall back to using "1.1" automatically. This setting will indicate which version was used.

OtherHeaders:   Other headers as determined by the user (optional).

This configuration setting can be set to a string of headers to be appended to the HTTP request headers.

The headers must follow the format "header: value" as described in the HTTP specifications. Header lines should be separated by CRLF ("\r\n") .

Use this configuration setting with caution. If this configuration setting contains invalid headers, HTTP requests may fail.

This configuration setting is useful for extending the functionality of the component beyond what is provided.

ProxyAuthorization:   The authorization string to be sent to the proxy server.

This is similar to the Authorization configuration setting, but is used for proxy authorization. If this configuration setting contains a nonempty string, a Proxy-Authorization HTTP request header is added to the request. This header conveys proxy Authorization information to the server. If User and Password are specified, this value is calculated using the algorithm specified by AuthScheme.

ProxyAuthScheme:   The authorization scheme to be used for the proxy.

This configuration setting is provided for use by components that do not directly expose Proxy properties.

ProxyPassword:   A password if authentication is to be used for the proxy.

This configuration setting is provided for use by components that do not directly expose Proxy properties.

ProxyPort:   Port for the proxy server (default 80).

This configuration setting is provided for use by components that do not directly expose Proxy properties.

ProxyServer:   Name or IP address of a proxy server (optional).

This configuration setting is provided for use by components that do not directly expose Proxy properties.

ProxyUser:   A user name if authentication is to be used for the proxy.

This configuration setting is provided for use by components that do not directly expose Proxy properties.

SentHeaders:   The full set of headers as sent by the client.

This configuration setting returns the complete set of raw headers as sent by the client.

StatusCode:   The status code of the last response from the server.

This configuration setting contains the result code of the last response from the server.

StatusLine:   The first line of the last response from the server.

This setting contains the first line of the last response from the server. The format of the line will be [HTTP version] [Result Code] [Description].

TransferredData:   The contents of the last response from the server.

This configuration setting contains the contents of the last response from the server.

TransferredDataLimit:   The maximum number of incoming bytes to be stored by the component.

If TransferredDataLimit is set to 0 (default), no limits are imposed. Otherwise, this reflects the maximum number of incoming bytes that can be stored by the component.

TransferredHeaders:   The full set of headers as received from the server.

This configuration setting returns the complete set of raw headers as received from the server.

TransferredRequest:   The full request as sent by the client.

This configuration setting returns the full request as sent by the client. For performance reasons, the request is not normally saved. Set this configuration setting to ON before making a request to enable it. Following are examples of this request:

.NET Http http = new Http(); http.Config("TransferredRequest=on"); http.PostData = "body"; http.Post("http://someserver.com"); Console.WriteLine(http.Config("TransferredRequest")); C++ HTTP http; http.Config("TransferredRequest=on"); http.SetPostData("body", 5); http.Post("http://someserver.com"); printf("%s\r\n", http.Config("TransferredRequest"));

UseChunkedEncoding:   Enables or Disables HTTP chunked encoding for transfers.

If UseChunkedEncoding is set to True, the component will use HTTP-chunked encoding when posting, if possible. HTTP-chunked encoding allows large files to be sent in chunks instead of all at once. If set to False, the component will not use HTTP-chunked encoding. The default value is False.

Note: Some servers (such as the ASP.NET Development Server) may not support chunked encoding.

UseIDNs:   Whether to encode hostnames to internationalized domain names.

This configuration setting specifies whether hostnames containing non-ASCII characters are encoded to internationalized domain names. When set to True, if a hostname contains non-ASCII characters, it is encoded using Punycode to an IDN (internationalized domain name).

The default value is False and the hostname will always be used exactly as specified.

UsePlatformDeflate:   Whether to use the platform implementation to decompress compressed responses.

This configuration setting specifies whether the platform's deflate-algorithm implementation is used to decompress responses that use compression. If set to True (default), the platform implementation is used. If set to False, an internal implementation is used.

UsePlatformHTTPClient:   Whether or not to use the platform HTTP client.

When using this configuration setting, if True, the component will use the default HTTP client for the platform (URLConnection in Java, WebRequest in .NET, or CFHTTPMessage in Mac/iOS) instead of the internal HTTP implementation. This is important for environments in which direct access to sockets is limited or not allowed (e.g., in the Google AppEngine).

UseProxyAutoConfigURL:   Whether to use a Proxy auto-config file when attempting a connection.

This configuration specifies whether the component will attempt to use the Proxy auto-config URL when establishing a connection and AutoDetect is set to True.

When True (default), the component will check for the existence of a Proxy auto-config URL, and if found, will determine the appropriate proxy to use.

UserAgent:   Information about the user agent (browser).

This is the value supplied in the HTTP User-Agent header. The default setting is "IPWorks HTTP Component - www.nsoftware.com".

Override the default with the name and version of your software.

TCPClient Config Settings

CloseStreamAfterTransfer:   If true, the component will close the upload or download stream after the transfer.

This setting determines whether the input or output stream is closed after the transfer completes. When set to True (default), all streams will be closed after a transfer is completed. In order to keep streams open after the transfer of data, set this to False. the default value is True.

ConnectionTimeout:   Sets a separate timeout value for establishing a connection.

When set, this configuration setting allows you to specify a different timeout value for establishing a connection. Otherwise, the component will use Timeout for establishing a connection and transmitting/receiving data.

FirewallAutoDetect:   Tells the component whether or not to automatically detect and use firewall system settings, if available.

This configuration setting is provided for use by components that do not directly expose Firewall properties.

FirewallHost:   Name or IP address of firewall (optional).

If a FirewallHost is given, requested connections will be authenticated through the specified firewall when connecting.

If the FirewallHost setting is set to a Domain Name, a DNS request is initiated. Upon successful termination of the request, the FirewallHost setting is set to the corresponding address. If the search is not successful, an error is returned.

Note: This setting is provided for use by components that do not directly expose Firewall properties.

FirewallListener:   If true, the component binds to a SOCKS firewall as a server (TCPClient only).

This entry is for TCPClient only and does not work for other components that descend from TCPClient.

If this entry is set, the component acts as a server. RemoteHost and RemotePort are used to tell the SOCKS firewall in which address and port to listen to. The firewall rules may ignore RemoteHost, and it is recommended that RemoteHost be set to empty string in this case.

RemotePort is the port in which the firewall will listen to. If set to 0, the firewall will select a random port. The binding (address and port) is provided through the ConnectionStatus event.

The connection to the firewall is made by calling the Connect method.

FirewallPassword:   Password to be used if authentication is to be used when connecting through the firewall.

If FirewallHost is specified, the FirewallUser and FirewallPassword settings are used to connect and authenticate to the given firewall. If the authentication fails, the component throws an exception.

Note: This setting is provided for use by components that do not directly expose Firewall properties.

FirewallPort:   The TCP port for the FirewallHost;.

The FirewallPort is set automatically when FirewallType is set to a valid value.

Note: This configuration setting is provided for use by components that do not directly expose Firewall properties.

FirewallType:   Determines the type of firewall to connect through.

The appropriate values are as follows:

0No firewall (default setting).
1Connect through a tunneling proxy. FirewallPort is set to 80.
2Connect through a SOCKS4 Proxy. FirewallPort is set to 1080.
3Connect through a SOCKS5 Proxy. FirewallPort is set to 1080.
10Connect through a SOCKS4A Proxy. FirewallPort is set to 1080.

Note: This setting is provided for use by components that do not directly expose Firewall properties.

FirewallUser:   A user name if authentication is to be used connecting through a firewall.

If the FirewallHost is specified, the FirewallUser and FirewallPassword settings are used to connect and authenticate to the Firewall. If the authentication fails, the component throws an exception.

Note: This setting is provided for use by components that do not directly expose Firewall properties.

KeepAliveInterval:   The retry interval, in milliseconds, to be used when a TCP keep-alive packet is sent and no response is received.

When set, TCPKeepAlive will automatically be set to True. A TCP keep-alive packet will be sent after a period of inactivity as defined by KeepAliveTime. If no acknowledgment is received from the remote host, the keep-alive packet will be sent again. This configuration setting specifies the interval at which the successive keep-alive packets are sent in milliseconds. This system default if this value is not specified here is 1 second.

Note: This value is not applicable in macOS.

KeepAliveTime:   The inactivity time in milliseconds before a TCP keep-alive packet is sent.

When set, TCPKeepAlive will automatically be set to True. By default, the operating system will determine the time a connection is idle before a Transmission Control Protocol (TCP) keep-alive packet is sent. This system default if this value is not specified here is 2 hours. In many cases, a shorter interval is more useful. Set this value to the desired interval in milliseconds.

Linger:   When set to True, connections are terminated gracefully.

This property controls how a connection is closed. The default is True.

In the case that Linger is True (default), two scenarios determine how long the connection will linger. In the first, if LingerTime is 0 (default), the system will attempt to send pending data for a connection until the default IP timeout expires.

In the second scenario, if LingerTime is a positive value, the system will attempt to send pending data until the specified LingerTime is reached. If this attempt fails, then the system will reset the connection.

The default behavior (which is also the default mode for stream sockets) might result in a long delay in closing the connection. Although the component returns control immediately, the system could hold system resources until all pending data are sent (even after your application closes).

Setting this property to False forces an immediate disconnection. If you know that the other side has received all the data you sent (e.g., by a client acknowledgment), setting this property to False might be the appropriate course of action.

LingerTime:   Time in seconds to have the connection linger.

LingerTime is the time, in seconds, the socket connection will linger. This value is 0 by default, which means it will use the default IP timeout.

LocalHost:   The name of the local host through which connections are initiated or accepted.

The LocalHost setting contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multi-homed hosts (machines with more than one IP interface) setting LocalHost to the value of an interface will make the component initiate connections (or accept in the case of server components) only through that interface.

If the component is connected, the LocalHost setting shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multi-homed hosts (machines with more than one IP interface).

LocalPort:   The port in the local host where the component binds.

This must be set before a connection is attempted. It instructs the component to bind to a specific port (or communication endpoint) in the local machine.

Setting this to 0 (default) enables the system to choose a port at random. The chosen port will be shown by LocalPort after the connection is established.

LocalPort cannot be changed once a connection is made. Any attempt to set this when a connection is active will generate an error.

This; setting is useful when trying to connect to services that require a trusted port in the client side. An example is the remote shell (rsh) service in UNIX systems.

MaxLineLength:   The maximum amount of data to accumulate when no EOL is found.

MaxLineLength is the size of an internal buffer, which holds received data while waiting for an EOL string.

If an EOL string is found in the input stream before MaxLineLength bytes are received, the DataIn event is fired with the EOL parameter set to True, and the buffer is reset.

If no EOL is found, and MaxLineLength bytes are accumulated in the buffer, the DataIn event is fired with the EOL parameter set to False, and the buffer is reset.

The minimum value for MaxLineLength is 256 bytes. The default value is 2048 bytes.

MaxTransferRate:   The transfer rate limit in bytes per second.

This configuration setting can be used to throttle outbound TCP traffic. Set this to the number of bytes to be sent per second. By default, this is not set and there is no limit.

ProxyExceptionsList:   A semicolon separated list of hosts and IPs to bypass when using a proxy.

This configuration setting optionally specifies a semicolon-separated list of hostnames or IP addresses to bypass when a proxy is in use. When requests are made to hosts specified in this property, the proxy will not be used. For instance:

www.google.com;www.nsoftware.com

TCPKeepAlive:   Determines whether or not the keep alive socket option is enabled.

If set to True, the socket's keep-alive option is enabled and keep-alive packets will be sent periodically to maintain the connection. Set KeepAliveTime and KeepAliveInterval to configure the timing of the keep-alive packets.

Note: This value is not applicable in Java.

TcpNoDelay:   Whether or not to delay when sending packets.

When true, the socket will send all data that is ready to send at once. When false, the socket will send smaller buffered packets of data at small intervals. This is known as the Nagle algorithm.

By default, this config is set to false.

UseIPv6:   Whether to use IPv6.

When set to 0 (default), the component will use IPv4 exclusively. When set to 1, the component will use IPv6 exclusively. To instruct the component to prefer IPv6 addresses, but use IPv4 if IPv6 is not supported on the system, this setting should be set to 2. The default value is 0. Possible values are:

0 IPv4 Only
1 IPv6 Only
2 IPv6 with IPv4 fallback
UseNTLMv2:   Whether to use NTLM V2.

When authenticating with NTLM, this setting specifies whether NTLM V2 is used. By default this value is False and NTLM V1 will be used. Set this to True to use NTLM V2.

SSL Config Settings

CACertFilePaths:   The paths to CA certificate files when using Mono on Unix/Linux.

This setting specifies the paths on disk to CA certificate files when using Mono on Unix/Linux. It is not applicable in any other circumstances.

The value is formatted as a list of paths separated by semicolons. The component will check for the existence of each file in the order specified. When a file is found the CA certificates within the file will be loaded and used to determine the validity of server or client certificates.

The default value is:

/etc/ssl/ca-bundle.pem;/etc/pki/tls/certs/ca-bundle.crt;/etc/ssl/certs/ca-certificates.crt;/etc/pki/tls/cacert.pem

LogSSLPackets:   Controls whether SSL packets are logged when using the internal security API.

When SSLProvider is set to Internal, this setting controls whether SSL packets should be logged. By default, this setting is False, as it is only useful for debugging purposes.

When enabled, SSL packet logs are output using the SSLStatus event, which will fire each time an SSL packet is sent or received.

Enabling this setting has no effect if SSLProvider is set to Platform.

ReuseSSLSession:   Determines if the SSL session is reused.

If set to true, the component will reuse the context if and only if the following criteria are met:

  • The target host name is the same.
  • The system cache entry has not expired (default timeout is 10 hours).
  • The application process that calls the function is the same.
  • The logon session is the same.
  • The instance of the component is the same.

SSLCACerts:   A newline separated list of CA certificate to use during SSL client authentication.

This setting specifies one or more CA certificates to be included in the request when performing SSL client authentication. Some servers require the entire chain, including CA certificates, to be presented when performing SSL client authentication. The value of this setting is a newline (CrLf) separated list of certificates. For instance:

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
..
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

SSLCheckCRL:   Whether to check the Certificate Revocation List for the server certificate.

This setting specifies whether the component will check the Certificate Revocation List specified by the server certificate. If set to 1 or 2, the component will first obtain the list of CRL URLs from the server certificate's CRL distribution points extension. The component will then make HTTP requests to each CRL endpoint to check the validity of the server's certificate. If the certificate has been revoked or any other issues are found during validation the component throws an exception.

When set to 0 (default) the CRL check will not be performed by the component. When set to 1, it will attempt to perform the CRL check, but will continue without an error if the server's certificate does not support CRL. When set to 2, it will perform the CRL check and will throw an error if CRL is not supported.

This configuration setting is only supported in the Java, C#, and C++ editions. In the C++ edition, it is only supported on Windows operating systems.

SSLCheckOCSP:   Whether to use OCSP to check the status of the server certificate.

This setting specifies whether the component will use OCSP to check the validity of the server certificate. If set to 1 or 2, the component will first obtain the OCSP URL from the server certificate's OCSP extension. The component will then locate the issuing certificate and make an HTTP request to the OCSP endpoint to check the validity of the server's certificate. If the certificate has been revoked or any other issues are found during validation the component throws an exception.

When set to 0 (default) the component will not perform an OCSP check. When set to 1, it will attempt to perform the OCSP check, but will continue without an error if the server's certificate does not support OCSP. When set to 2, it will perform the OCSP check and will throw an error if OCSP is not supported.

This configuration setting is only supported in the Java, C#, and C++ editions. In the C++ edition, it is only supported on Windows operating systems.

SSLCipherStrength:   The minimum cipher strength used for bulk encryption.

This minimum cipher strength largely dependent on the security modules installed on the system. If the cipher strength specified is not supported, an error will be returned when connections are initiated.

Please note that this setting contains the minimum cipher strength requested from the security library. The actual cipher strength used for the connection is shown by the SSLStatus event.

Use this setting with caution. Requesting a lower cipher strength than necessary could potentially cause serious security vulnerabilities in your application.

When the provider is OpenSSL, SSLCipherStrength is currently not supported. This functionality is instead made available through the OpenSSLCipherList config setting.

SSLEnabledCipherSuites:   The cipher suite to be used in an SSL negotiation.

The enabled cipher suites to be used in SSL negotiation.

By default, the enabled cipher suites will include all available ciphers ("*").

The special value "*" means that the component will pick all of the supported cipher suites. If SSLEnabledCipherSuites is set to any other value, only the specified cipher suites will be considered.

Multiple cipher suites are separated by semicolons.

Example values when SSLProvider is set to Platform: obj.config("SSLEnabledCipherSuites=*"); obj.config("SSLEnabledCipherSuites=CALG_AES_256"); obj.config("SSLEnabledCipherSuites=CALG_AES_256;CALG_3DES"); Possible values when SSLProvider is set to Platform include:

  • CALG_3DES
  • CALG_3DES_112
  • CALG_AES
  • CALG_AES_128
  • CALG_AES_192
  • CALG_AES_256
  • CALG_AGREEDKEY_ANY
  • CALG_CYLINK_MEK
  • CALG_DES
  • CALG_DESX
  • CALG_DH_EPHEM
  • CALG_DH_SF
  • CALG_DSS_SIGN
  • CALG_ECDH
  • CALG_ECDH_EPHEM
  • CALG_ECDSA
  • CALG_ECMQV
  • CALG_HASH_REPLACE_OWF
  • CALG_HUGHES_MD5
  • CALG_HMAC
  • CALG_KEA_KEYX
  • CALG_MAC
  • CALG_MD2
  • CALG_MD4
  • CALG_MD5
  • CALG_NO_SIGN
  • CALG_OID_INFO_CNG_ONLY
  • CALG_OID_INFO_PARAMETERS
  • CALG_PCT1_MASTER
  • CALG_RC2
  • CALG_RC4
  • CALG_RC5
  • CALG_RSA_KEYX
  • CALG_RSA_SIGN
  • CALG_SCHANNEL_ENC_KEY
  • CALG_SCHANNEL_MAC_KEY
  • CALG_SCHANNEL_MASTER_HASH
  • CALG_SEAL
  • CALG_SHA
  • CALG_SHA1
  • CALG_SHA_256
  • CALG_SHA_384
  • CALG_SHA_512
  • CALG_SKIPJACK
  • CALG_SSL2_MASTER
  • CALG_SSL3_MASTER
  • CALG_SSL3_SHAMD5
  • CALG_TEK
  • CALG_TLS1_MASTER
  • CALG_TLS1PRF
Example values when SSLProvider is set to Internal: obj.config("SSLEnabledCipherSuites=*"); obj.config("SSLEnabledCipherSuites=TLS_DHE_DSS_WITH_AES_128_CBC_SHA"); obj.config("SSLEnabledCipherSuites=TLS_DHE_DSS_WITH_AES_128_CBC_SHA;TLS_DH_ANON_WITH_AES_128_CBC_SHA"); Possible values when SSLProvider is set to Internal include:
  • TLS_ECDHE_ECDSA_WITH_AES_256_GCM_SHA384
  • TLS_ECDHE_ECDSA_WITH_AES_128_GCM_SHA256
  • TLS_ECDHE_RSA_WITH_AES_128_GCM_SHA256
  • TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384
  • TLS_ECDH_ECDSA_WITH_AES_256_GCM_SHA384
  • TLS_RSA_WITH_AES_256_GCM_SHA384
  • TLS_RSA_WITH_AES_128_GCM_SHA256
  • TLS_ECDH_ECDSA_WITH_AES_128_GCM_SHA256
  • TLS_DHE_DSS_WITH_AES_256_GCM_SHA384
  • TLS_DHE_RSA_WITH_AES_256_GCM_SHA384
  • TLS_ECDH_RSA_WITH_AES_256_GCM_SHA384
  • TLS_ECDH_RSA_WITH_AES_128_GCM_SHA256
  • TLS_DHE_RSA_WITH_AES_128_GCM_SHA256
  • TLS_DHE_DSS_WITH_AES_128_GCM_SHA256
  • TLS_DH_RSA_WITH_AES_128_GCM_SHA256 (Not Recommended)
  • TLS_DH_RSA_WITH_AES_256_GCM_SHA384 (Not Recommended)
  • TLS_DH_DSS_WITH_AES_128_GCM_SHA256 (Not Recommended)
  • TLS_DH_DSS_WITH_AES_256_GCM_SHA384 (Not Recommended)
  • TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA384
  • TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA256
  • TLS_ECDH_ECDSA_WITH_AES_256_CBC_SHA384
  • TLS_DHE_DSS_WITH_AES_256_CBC_SHA256
  • TLS_RSA_WITH_AES_256_CBC_SHA256
  • TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA384
  • TLS_ECDH_RSA_WITH_AES_256_CBC_SHA384
  • TLS_DHE_RSA_WITH_AES_256_CBC_SHA256
  • TLS_DHE_RSA_WITH_AES_128_CBC_SHA256
  • TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA256
  • TLS_RSA_WITH_AES_128_CBC_SHA256
  • TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA256
  • TLS_ECDH_RSA_WITH_AES_128_CBC_SHA256
  • TLS_DHE_DSS_WITH_AES_128_CBC_SHA256
  • TLS_RSA_WITH_AES_256_CBC_SHA
  • TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA
  • TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA
  • TLS_ECDH_ECDSA_WITH_AES_256_CBC_SHA
  • TLS_DHE_RSA_WITH_AES_256_CBC_SHA
  • TLS_ECDH_RSA_WITH_AES_256_CBC_SHA
  • TLS_DHE_DSS_WITH_AES_256_CBC_SHA
  • TLS_RSA_WITH_AES_128_CBC_SHA
  • TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
  • TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA
  • TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA
  • TLS_ECDH_RSA_WITH_AES_128_CBC_SHA
  • TLS_DHE_RSA_WITH_AES_128_CBC_SHA
  • TLS_DHE_DSS_WITH_AES_128_CBC_SHA
  • TLS_ECDHE_ECDSA_WITH_3DES_EDE_CBC_SHA
  • TLS_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA
  • TLS_ECDH_ECDSA_WITH_3DES_EDE_CBC_SHA
  • TLS_ECDH_RSA_WITH_3DES_EDE_CBC_SHA
  • TLS_DHE_RSA_WITH_3DES_EDE_CBC_SHA
  • TLS_DHE_DSS_WITH_3DES_EDE_CBC_SHA
  • TLS_RSA_WITH_3DES_EDE_CBC_SHA
  • TLS_RSA_WITH_DES_CBC_SHA
  • TLS_DHE_RSA_WITH_DES_CBC_SHA
  • TLS_DHE_DSS_WITH_DES_CBC_SHA
  • TLS_RSA_WITH_RC4_128_MD5
  • TLS_RSA_WITH_RC4_128_SHA

When TLS 1.3 is negotiated (see SSLEnabledProtocols) only the following cipher suites are supported:

  • TLS_AES_256_GCM_SHA384
  • TLS_CHACHA20_POLY1305_SHA256
  • TLS_AES_128_GCM_SHA256

SSLEnabledCipherSuites is used together with SSLCipherStrength.

SSLEnabledProtocols:   Used to enable/disable the supported security protocols.

Used to enable/disable the supported security protocols.

Not all supported protocols are enabled by default (the value of this setting is 4032). If you want more granular control over the enabled protocols, you can set this property to the binary 'OR' of one or more of the following values:

TLS1.312288 (Hex 3000)
TLS1.23072 (Hex C00) (Default)
TLS1.1768 (Hex 300) (Default)
TLS1 192 (Hex C0) (Default)
SSL3 48 (Hex 30) [Platform Only]
SSL2 12 (Hex 0C) [Platform Only]

SSLEnabledProtocols - TLS 1.3 Notes

By default when TLS 1.3 is enabled the component will use the internal TLS implementation when the SSLProvider is set to Automatic for all editions.

In editions which are designed to run on Windows SSLProvider can be set to Platform to use the platform implementation instead of the internal implementation. When configured in this manner, please note that the platform provider is only supported on Windows 11 / Windows Server 2022 and up. The default internal provider is available on all platforms and is not restricted to any specific OS version.

If set to 1 (Platform provider) please be aware of the following notes:

  • The platform provider is only available on Windows 11 / Windows Server 2022 and up.
  • SSLEnabledCipherSuites and other similar SSL configuration settings are not supported.
  • If SSLEnabledProtocols includes both TLS 1.3 and TLS 1.2 the above restrictions are still applicable even if TLS 1.2 is negotiated. Enabling TLS 1.3 with the platform provider changes the implementation used for all TLS versions.

SSLEnabledProtocols: SSL2 and SSL3 Notes:

SSL 2.0 and 3.0 are not supported by the component when the SSLProvider is set to internal. To use SSL 2.0 or SSL 3.0, the platform security API must have the protocols enabled and SSLProvider needs to be set to platform.

SSLEnableRenegotiation:   Whether the renegotiation_info SSL extension is supported.

This setting specifies whether the renegotiation_info SSL extension will be used in the request when using the internal security API. This setting is true by default, but can be set to false to disable the extension.

This setting is only applicable when SSLProvider is set to Internal.

SSLIncludeCertChain:   Whether the entire certificate chain is included in the SSLServerAuthentication event.

This setting specifies whether the Encoded parameter of the SSLServerAuthentication event contains the full certificate chain. By default this value is False and only the leaf certificate will be present in the Encoded parameter of the SSLServerAuthentication event.

If set to True all certificates returned by the server will be present in the Encoded parameter of the SSLServerAuthentication event. This includes the leaf certificate, any intermediate certificate, and the root certificate.

Note: When SSLProvider is set to Internal this value is automatically set to true. This is needed for proper validation when using the internal provider.

SSLKeyLogFile:   The location of a file where per-session secrets are written for debugging purposes.

This setting optionally specifies the full path to a file on disk where per-session secrets are stored for debugging purposes.

When set, the component will save the session secrets in the same format as the SSLKEYLOGFILE environment variable functionality used by most major browsers and tools such as Chrome, Firefox, and cURL. This file can then be used in tools such as Wireshark to decrypt TLS traffice for debugging purposes. When writing to this file the component will only append, it will not overwrite previous values.

Note: This setting is only applicable when SSLProvider is set to Internal.

SSLNegotiatedCipher:   Returns the negotiated cipher suite.

Returns the cipher suite negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipher[connId]");

SSLNegotiatedCipherStrength:   Returns the negotiated cipher suite strength.

Returns the strength of the cipher suite negotiated during the SSL handshake.

Note: For server components (e.g.TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipherStrength[connId]");

SSLNegotiatedCipherSuite:   Returns the negotiated cipher suite.

Returns the cipher suite negotiated during the SSL handshake represented as a single string.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipherSuite[connId]");

SSLNegotiatedKeyExchange:   Returns the negotiated key exchange algorithm.

Returns the key exchange algorithm negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedKeyExchange[connId]");

SSLNegotiatedKeyExchangeStrength:   Returns the negotiated key exchange algorithm strength.

Returns the strenghth of the key exchange algorithm negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedKeyExchangeStrength[connId]");

SSLNegotiatedVersion:   Returns the negotiated protocol version.

Returns the protocol version negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedVersion[connId]");

SSLSecurityFlags:   Flags that control certificate verification.

The following flags are defined (specified in hexadecimal notation). They can be or-ed together to exclude multiple conditions:

0x00000001Ignore time validity status of certificate.
0x00000002Ignore time validity status of CTL.
0x00000004Ignore non-nested certificate times.
0x00000010Allow unknown Certificate Authority.
0x00000020Ignore wrong certificate usage.
0x00000100Ignore unknown certificate revocation status.
0x00000200Ignore unknown CTL signer revocation status.
0x00000400Ignore unknown Certificate Authority revocation status.
0x00000800Ignore unknown Root revocation status.
0x00008000Allow test Root certificate.
0x00004000Trust test Root certificate.
0x80000000Ignore non-matching CN (certificate CN not-matching server name).

This functionality is currently not available in Java or when the provider is OpenSSL.

SSLServerCACerts:   A newline separated list of CA certificate to use during SSL server certificate validation.

This setting optionally specifies one or more CA certificates to be used when verifying the server certificate. When verifying the server's certificate the certificates trusted by the system will be used as part of the verification process. If the server's CA certificates are not installed to the trusted system store, they may be specified here so they are included when performing the verification process. This setting should only be set if the server's CA certificates are not already trusted on the system and cannot be installed to the trusted system store.

The value of this setting is a newline (CrLf) separated list of certificates. For instance:

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
..
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

TLS12SignatureAlgorithms:   Defines the allowed TLS 1.2 signature algorithms when SSLProvider is set to Internal.

This setting specifies the allowed server certificate signature algorithms when SSLProvider is set to Internal and SSLEnabledProtocols is set to allow TLS 1.2.

When specified the component will verify that the server certificate signature algorithm is among the values specified in this setting. If the server certificate signature algorithm is unsupported the component throws an exception.

The format of this value is a comma separated list of hash-signature combinations. For instance: component.SSLProvider = TCPClientSSLProviders.sslpInternal; component.Config("SSLEnabledProtocols=3072"); //TLS 1.2 component.Config("TLS12SignatureAlgorithms=sha256-rsa,sha256-dsa,sha1-rsa,sha1-dsa"); The default value for this setting is sha512-ecdsa,sha512-rsa,sha512-dsa,sha384-ecdsa,sha384-rsa,sha384-dsa,sha256-ecdsa,sha256-rsa,sha256-dsa,sha224-ecdsa,sha224-rsa,sha224-dsa,sha1-ecdsa,sha1-rsa,sha1-dsa.

In order to not restrict the server's certificate signature algorithm, specify an empty string as the value for this setting, which will cause the signature_algorithms TLS 1.2 extension to not be sent.

TLS12SupportedGroups:   The supported groups for ECC.

This setting specifies a comma separated list of named groups used in TLS 1.2 for ECC.

The default value is ecdhe_secp256r1,ecdhe_secp384r1,ecdhe_secp521r1.

When using TLS 1.2 and SSLProvider is set to Internal, the values refer to the supported groups for ECC. The following values are supported:

  • "ecdhe_secp256r1" (default)
  • "ecdhe_secp384r1" (default)
  • "ecdhe_secp521r1" (default)

TLS13KeyShareGroups:   The groups for which to pregenerate key shares.

This setting specifies a comma separated list of named groups used in TLS 1.3 for key exchange. The groups specified here will have key share data pregenerated locally before establishing a connection. This can prevent an additional round trip during the handshake if the group is supported by the server.

The default value is set to balance common supported groups and the computational resources required to generate key shares. As a result only some groups are included by default in this setting.

Note: All supported groups can always be used during the handshake even if not listed here, but if a group is used which is not present in this list it will incur an additional round trip and time to generate the key share for that group.

In most cases this setting does not need to be modified. This should only be modified if there is a specific reason to do so.

The default value is ecdhe_x25519,ecdhe_secp256r1,ecdhe_secp384r1,ffdhe_2048,ffdhe_3072

The values are ordered from most preferred to least preferred. The following values are supported:

  • "ecdhe_x25519" (default)
  • "ecdhe_x448"
  • "ecdhe_secp256r1" (default)
  • "ecdhe_secp384r1" (default)
  • "ecdhe_secp521r1"
  • "ffdhe_2048" (default)
  • "ffdhe_3072" (default)
  • "ffdhe_4096"
  • "ffdhe_6144"
  • "ffdhe_8192"

TLS13SignatureAlgorithms:   The allowed certificate signature algorithms.

This setting holds a comma separated list of allowed signature algorithms. Possible values are:

  • "ed25519" (default)
  • "ed448" (default)
  • "ecdsa_secp256r1_sha256" (default)
  • "ecdsa_secp384r1_sha384" (default)
  • "ecdsa_secp521r1_sha512" (default)
  • "rsa_pkcs1_sha256" (default)
  • "rsa_pkcs1_sha384" (default)
  • "rsa_pkcs1_sha512" (default)
  • "rsa_pss_sha256" (default)
  • "rsa_pss_sha384" (default)
  • "rsa_pss_sha512" (default)
The default value is rsa_pss_sha256,rsa_pss_sha384,rsa_pss_sha512,rsa_pkcs1_sha256,rsa_pkcs1_sha384,rsa_pkcs1_sha512,ecdsa_secp256r1_sha256,ecdsa_secp384r1_sha384,ecdsa_secp521r1_sha512,ed25519,ed448. This setting is only applicable when SSLEnabledProtocols includes TLS 1.3.
TLS13SupportedGroups:   The supported groups for (EC)DHE key exchange.

This setting specifies a comma separated list of named groups used in TLS 1.3 for key exchange. This setting should only be modified if there is a specific reason to do so.

The default value is ecdhe_x25519,ecdhe_x448,ecdhe_secp256r1,ecdhe_secp384r1,ecdhe_secp521r1,ffdhe_2048,ffdhe_3072,ffdhe_4096,ffdhe_6144,ffdhe_8192

The values are ordered from most preferred to least preferred. The following values are supported:

  • "ecdhe_x25519" (default)
  • "ecdhe_x448" (default)
  • "ecdhe_secp256r1" (default)
  • "ecdhe_secp384r1" (default)
  • "ecdhe_secp521r1" (default)
  • "ffdhe_2048" (default)
  • "ffdhe_3072" (default)
  • "ffdhe_4096" (default)
  • "ffdhe_6144" (default)
  • "ffdhe_8192" (default)

Socket Config Settings

AbsoluteTimeout:   Determines whether timeouts are inactivity timeouts or absolute timeouts.

If AbsoluteTimeout is set to True, any method which does not complete within Timeout seconds will be aborted. By default, AbsoluteTimeout is False, and the timeout is an inactivity timeout.

Note: This option is not valid for UDP ports.

FirewallData:   Used to send extra data to the firewall.

When the firewall is a tunneling proxy, use this property to send custom (additional) headers to the firewall (e.g. headers for custom authentication schemes).

InBufferSize:   The size in bytes of the incoming queue of the socket.

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be receiving. Increasing the value of the InBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the component is activated the InBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

OutBufferSize:   The size in bytes of the outgoing queue of the socket.

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be sending. Increasing the value of the OutBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the component is activated the OutBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

Base Config Settings

BuildInfo:   Information about the product's build.

When queried, this setting will return a string containing information about the product's build.

GUIAvailable:   Whether or not a message loop is available for processing events.

In a GUI-based application, long-running blocking operations may cause the application to stop responding to input until the operation returns. The component will attempt to discover whether or not the application has a message loop and, if one is discovered, it will process events in that message loop during any such blocking operation.

In some non-GUI applications, an invalid message loop may be discovered that will result in errant behavior. In these cases, setting GUIAvailable to false will ensure that the component does not attempt to process external events.

LicenseInfo:   Information about the current license.

When queried, this setting will return a string containing information about the license this instance of a component is using. It will return the following information:

  • Product: The product the license is for.
  • Product Key: The key the license was generated from.
  • License Source: Where the license was found (e.g., RuntimeLicense, License File).
  • License Type: The type of license installed (e.g., Royalty Free, Single Server).
  • Last Valid Build: The last valid build number for which the license will work.
MaskSensitive:   Whether sensitive data is masked in log messages.

In certain circumstances it may be beneficial to mask sensitive data, like passwords, in log messages. Set this to true to mask sensitive data. The default is true.

This setting only works on these components: AS3Receiver, AS3Sender, Atom, Client(3DS), FTP, FTPServer, IMAP, OFTPClient, SSHClient, SCP, Server(3DS), Sexec, SFTP, SFTPServer, SSHServer, TCPClient, TCPServer.

UseFIPSCompliantAPI:   Tells the component whether or not to use FIPS certified APIs.

When set to true, the component will utilize the underlying operating system's certified APIs. Java editions, regardless of OS, utilize Bouncy Castle FIPS, while all the other Windows editions make use of Microsoft security libraries.

FIPS mode can be enabled by setting the UseFIPSCompliantAPI configuration setting to true. This is a static setting which applies to all instances of all components of the toolkit within the process. It is recommended to enable or disable this setting once before the component has been used to establish a connection. Enabling FIPS while an instance of the component is active and connected may result in unexpected behavior.

For more details please see the FIPS 140-2 Compliance article.

Note: This setting is only applicable on Windows.

Note: Enabling FIPS-compliance requires a special license; please contact sales@nsoftware.com for details.

UseInternalSecurityAPI:   Whether or not to use the system security libraries or an internal implementation.

When set to false, the component will use the system security libraries by default to perform cryptographic functions where applicable. In this case, calls to unmanaged code will be made. In certain environments, this is not desirable. To use a completely managed security implementation, set this setting to true.

Setting this configuration setting to true tells the component to use the internal implementation instead of using the system security libraries.

On Windows, this setting is set to false by default. On Linux/macOS, this setting is set to true by default.

If using the .NET Standard Library, this setting will be true on all platforms. The .NET Standard library does not support using the system security libraries.

Note: This setting is static. The value set is applicable to all components used in the application.

When this value is set, the product's system dynamic link library (DLL) is no longer required as a reference, as all unmanaged code is stored in that file.

Trappable Errors (AS2Sender Component)

AS2Sender Errors

118   Firewall Error. Error description contains detailed message.
143   Busy performing current action.
151   HTTP protocol error. The error message has the server response.
152   No server specified in URL
153   Specified URL scheme is invalid.
283   No MIME-boundary found.
501   Unable to parse the receipt.
502   The receipt is signed with an unsupported signature format (details follow).
511   Unsupported compression algorithm requested.
521   A Message Integrity Check was requested, but not provided in the MDN.
522   The Message Integrity Check returned in the MDN is incorrect.
523   Unable to parse Message Integrity Check.
524   Unrequested hashing algorithm used (check MDNOptions).
525   The Message ID returned in the MDN does not match.
531   The receipt was unsigned, and a signed receipt was expected.
532   The receipt signature could not be verified.
533   An MDN was expected in the HTTP reply, but was not returned.
600   Failure reported in MDN: Unsupported signing protocol.
601   Failure reported in MDN: Unsupported MIC algorithms.
602   Failure reported in MDN: Other (details follow).
611   Error reported in MDN: Decryption failed.
612   Error reported in MDN: Authentication failed.
613   Error reported in MDN: Could not verify content integrity.
614   Error reported in MDN: Unexpected processing error.
615   Error reported in MDN: Other (details follow).
621   Warning reported in MDN: Authentication failed, processing continued by receiver.
622   Warning reported in MDN: Other (details follow).
831   I/O Error (details follow).

SMIME Errors

10191   Invalid index (RecipientIndex).
10192   Message decoding error (code).
10193   Unexpected message type.
10194   Unsupported hashing/signing algorithm.
10195   The message does not have any signers.
10196   The message signature could not be verified.
10197   Could not locate a suitable decryption certificate.
10198   The signer certificate could not be found.
10199   No signing certificate was supplied for signing the message.
10201   The specified certificate was not the one required.
10202   The specified certificate could not be found.
10221   Could not acquire CSP.
10222   Type validation error.
10223   Unsupported key size.
10224   Unrecognized Content-Type object identifier.
10225   Unrecognized public key format.
10226   No choices specified.
10228   Must specify output stream.
10280   Invalid part index.
10281   Unknown MIME type.
10283   No MIME-boundary found.
10280   Error decoding certificate.