/n software Adapters for BizTalk
Version 22.0 [Build 8376]

SCP Adapter

Properties   Config Settings  

The SCP Component adds SSH-secured file transfer capabilities to your BizTalk Server.

Remarks

The SCP Adapter adds a SCP client to your BizTalk Server that enables it with SSH-secured file download and upload functionality.

SCP Receive Adapter

The SCP Receive Adapter requires that a single property be set: SSHHost. You may also set an SSHPort if the server is not running on the default SSH port. In order to authenticate with the SSH server, you will need to specify an SSHUser, and either SSHPassword or SSHCert depending upon the SSHAuthMode to be used.

The adapter will connect to the SCP server every PollingInterval and download the file(s) specified by FileMask. All files that match the FileMask will be downloaded and submitted to the BizTalk Message Engine as individual messages.

SCP Send Adapter

The SCP Send Adapter requires both an SSHHost and a RemoteFile. You may also set an SSHPort if the server is not running on the default SSH port. In order to authenticate with the SSH server, you will need to specify an SSHUser, and either SSHPassword or SSHCert depending upon the SSHAuthMode to be used.

The adapter will connect to the SCP server whenever it has a message to send. The adapter will attempt to upload to the specified RemotePath.

Please refer to the section on adapter configuration for a description of how to configure receive locations and send ports for this adapter.

Receiver Property List


The following is the full list of the properties of the receiver Adapter with short descriptions. Click on the links for further details.

ErrorThresholdThe maximum number of errors before the component shuts down.
FileMaskIndicates the type of files to download from the SSH server.
FirewallA set of properties related to firewall access.
MaxBatchSizeThe maximum size, in MB, of the current batch (0 indicates no limit).
MaxFileCountThe maximum number of files in the current batch (0 indicates no limit).
MaxFileSizeThe maximum size, in MB, of a file in the current batch (0 indicates no limit).
MaxThreadsThe maximum number of threads that the component may consume.
OtherDefines a set of configuration settings to be used by the component.
PersistentConnectionInstructs the component whether to keep the connection to the server open.
PollingIntervalThe amount of time, in seconds, between download attempts.
ReceivedFileNameThe name of the remote file received by the SCP component.
ReceivedFilePathThe remote path of the received file.
ReceivedFileSizeThe size of the remote file received by the SCP component.
ReceivedFileSSHUserThe SSH user name used by the SCP component when downloading the remote file.
RemotePathThe current path on the SSH server.
RequeueEndpointsWhether to requeue receive endpoints if the polling interval has not been reached.
RuntimeLicenseSpecifies the component runtime license key.
SSHAcceptServerHostKeyInstructs the component to accept the server host key that matches the supplied key.
SSHAuthModeThe type of authentication used by the component.
SSHCertThe certificate to use for client authentication during the SSH handshake.
SSHCompressionAlgorithmsA comma-separated list of compression algorithms allowed for this connection.
SSHHostThe address of the SSH host.
SSHPasswordThe password for SSH password-based authentication.
SSHPortThe port on the SSH server where the SSH service is running; by default, 22.
SSHUserThe username for SSH authentication.
SSOAffiliateSpecifies the name of the SSO Affiliate Application.
TempPathA temporary local directory where data can be stored before the component processes it.
TimeoutA timeout for the component.
TransportLogTells the component where and how to report information about its operations.
URIThe Uniform Resource Identifier (URI) of the send port or receive location.

Sender Property List


The following is the full list of the properties of the sender Adapter with short descriptions. Click on the links for further details.

ConnectionLifetimeInstructs the component whether or not to leave the connection to the server open.
FirewallA set of properties related to firewall access.
MaxPersistentConnectionsThe maximum number of simultaneous persistent connections when sending.
MaxThreadsThe maximum number of threads that the component may consume.
MaxTransmissionBatchSizeThe maximum number of messages that can be sent in a single batch.
OtherDefines a set of configuration settings to be used by the component.
RemoteFileThe name of the destination file on the SSH server for uploading.
RemotePathThe current path on the SSH server.
RuntimeLicenseSpecifies the component runtime license key.
SSHAcceptServerHostKeyInstructs the component to accept the server host key that matches the supplied key.
SSHAuthModeThe type of authentication used by the component.
SSHCertThe certificate to use for client authentication during the SSH handshake.
SSHCompressionAlgorithmsA comma-separated list of compression algorithms allowed for this connection.
SSHHostThe address of the SSH host.
SSHPasswordThe password for SSH password-based authentication.
SSHPortThe port on the SSH server where the SSH service is running; by default, 22.
SSHUserThe username for SSH authentication.
SSOAffiliateSpecifies the name of the SSO Affiliate Application.
TimeoutA timeout for the component.
TransmitBatchModeHow the transmitter processes batches.
TransportLogTells the component where and how to report information about its operations.
URIThe Uniform Resource Identifier (URI) of the send port or receive location.

Config Settings


The following is a list of config settings for the Adapter with short descriptions. Click on the links for further details.

DownloadIf set to true, the send component will download files instead of upload.
DownloadSingleFileIf set to true, the send component will download a file instead of upload.
FilePermissionsSpecifies the permissions of a file to be set after a successful upload.
KeyRenegotiationThresholdSets the threshold for the SSH Key Renegotiation.
LocalFileSpecifies the local file or file mask when uploading.
LogSSHPacketsIf True, detailed SSH packet logging is performed.
RecursiveModeIf set to true the component will recursively upload or download files.
ServerResponseWindowThe time to wait for a server response in milliseconds.
SSHAcceptServerHostKeyFingerPrintInstructs the component to accept the server's host key with this fingerprint.
SSHEncryptionAlgorithmsA comma-separated list containing all allowable compression algorithms.
SSHKeyExchangeAlgorithmsSpecifies the supported key exchange algorithms.
SSHMacAlgorithmsSpecifies the supported Mac algorithms.
SSHPublicKeyAlgorithmsSpecifies the supported public key algorithms for the server's public key.
AbsoluteTimeoutDetermines whether timeouts are inactivity timeouts or absolute timeouts.
LocalHostThe name of the local host or user-assigned IP interface through which connections are initiated or accepted.
TcpNoDelayWhether or not to delay when sending packets.
UseInternalSecurityAPITells the component whether or not to use the system security libraries or an internal implementation.

SCP Receiver

How to Configure a SCP Receive Location with the BizTalk Server Administration Console

To configure the receive location by using the BizTalk Server Administration console, use the following procedure:

NOTE: Before completing the following procedure you must have already added a one-way receive port. For more information, see How to Create a Receive Port.

To configure receive location variables for a SCP receive location:

  1. In the BizTalk Server Administration console, expand BizTalk Server Administration, expand BizTalk Group, expand Applications, and then expand the application you want to create a receive location in.
  2. In the left pane, click the Receive Port node. Then in the right pane, right-click the receive port that is associated with an existing receive location or that you want to associate with a new receive location, and then click Properties.
  3. In the left pane of the Receive Port Properties dialog box, select Receive Locations, and in the right pane double-click an existing receive location or click New to create a new receive location.
  4. In the Receive Location Properties dialog box, in the Transport section next to Type, select nsoftware.SCP 2022 from the drop-down list, and then click Configure to configure the transport properties for the receive location.
  5. In the nsoftware.SCP 2022 Transport Properties dialog box, you will find the following properties:
    ErrorThreshold

    The maximum number of errors before the component shuts down.

    Type: xs:int    Default Value: 5

    FileMask

    Indicates the type of files to download from the SSH server.

    Type: xs:string    Default Value: "*.*"

    Firewall

    A set of properties related to firewall access.

    Type: Firewall    Default Value: null

    MaxBatchSize

    The maximum size, in MB, of the current batch (0 indicates no limit).

    Type: xs:int    Default Value: 0

    MaxFileCount

    The maximum number of files in the current batch (0 indicates no limit).

    Type: xs:int    Default Value: 10

    MaxFileSize

    The maximum size, in MB, of a file in the current batch (0 indicates no limit).

    Type: xs:int    Default Value: 0

    MaxThreads

    The maximum number of threads that the component may consume.

    Type: xs:int    Default Value: 20

    Other

    Defines a set of configuration settings to be used by the component.

    Type: xs:string    Default Value: ""

    PersistentConnection

    Instructs the component whether to keep the connection to the server open.

    Type: bool    Default Value: false

    PollingInterval

    The amount of time, in seconds, between download attempts.

    Type: xs:int    Default Value: 60

    ReceivedFileName

    The name of the remote file received by the SCP component.

    Type: xs:string    Default Value: ""

    ReceivedFilePath

    The remote path of the received file.

    Type: xs:string    Default Value: ""

    ReceivedFileSize

    The size of the remote file received by the SCP component.

    Type: xs:int    Default Value: 0

    ReceivedFileSSHUser

    The SSH user name used by the SCP component when downloading the remote file.

    Type: xs:string    Default Value: ""

    RemotePath

    The current path on the SSH server.

    Type: xs:string    Default Value: ""

    RequeueEndpoints

    Whether to requeue receive endpoints if the polling interval has not been reached.

    Type: bool    Default Value: false

    RuntimeLicense

    Specifies the component runtime license key.

    Type: xs:string    Default Value: ""

    SSHAcceptServerHostKey

    Instructs the component to accept the server host key that matches the supplied key.

    Type: Certificate    Default Value: null

    SSHAuthMode

    The type of authentication used by the component.

    Type: xs:int    Default Value: 2

    SSHCert

    The certificate to use for client authentication during the SSH handshake.

    Type: Certificate    Default Value: null
    NOTE: The digital id must have a private key associated with it.

    SSHCompressionAlgorithms

    A comma-separated list of compression algorithms allowed for this connection.

    Type: xs:string    Default Value: "none"

    SSHHost

    The address of the SSH host.

    Type: xs:string    Default Value: ""
    NOTE: This property must have a value.

    SSHPassword

    The password for SSH password-based authentication.

    Type: baf:Password    Default Value: ""

    SSHPort

    The port on the SSH server where the SSH service is running; by default, 22.

    Type: xs:int    Default Value: 22

    SSHUser

    The username for SSH authentication.

    Type: xs:string    Default Value: ""

    SSOAffiliate

    Specifies the name of the SSO Affiliate Application.

    Type: baf:SSOList    Default Value: ""

    TempPath

    A temporary local directory where data can be stored before the component processes it.

    Type: xs:string    Default Value: ""

    Timeout

    A timeout for the component.

    Type: xs:int    Default Value: 60

    TransportLog

    Tells the component where and how to report information about its operations.

    Type: Log    Default Value: null

    URI

    The Uniform Resource Identifier (URI) of the send port or receive location.

    Type: xs:string    Default Value: ""

  6. Click OK.
  7. Enter the appropriate values in the Receive Location Properties dialog box to complete the configuration of the receive location and click OK to save settings. For information about the Receive Locations Properties dialog box, see How to Create a Receive Location.

SCP Transmitter

Setting the SCP Adapter Configuration Properties for a Dynamic Send Port

A dynamic send port does not provide any transport configuration options in BizTalk Explorer because it is expected that these properties will be provided with the context properties associated with the message. These properties can be set in a custom pipeline or in an orchestration. To set message configuration properties in an orchestration you can do the following:

  • Add a Construct Message shape to your orchestration.
  • Configure the Construct Message shape to construct a new message. (for example Message_2)
  • Add a Message Assignment shape to the Construct Message shape.
  • Add code to the Message Assignment shape to initialize the message that you constructed and to set the appropriate configuration properties for the message.

Configuring the SCP Send Port with the BizTalk Server Administration Console

To configure the send port by using the BizTalk Server Administration console, use the following procedure:

To configure variables for a SCP send port:

  1. In the BizTalk Server Administration console, create a new send port or double-click an existing send port to modify it. For more information, see How to Create a Send Port. Configure all of the send port options and specify nsoftware.SCP 2022 for the Type option in the Transport section of the General tab.
  2. On the General tab, in the Transport section, click the Configure button next to Type.
  3. In the nsoftware.SCP 2022 Transport Properties dialog box, use the following properties to:


    ConnectionLifetime Instructs the component whether or not to leave the connection to the server open.
    Type: xs:int    Default Value: 0
    Firewall A set of properties related to firewall access.
    Type: Firewall    Default Value: null
    MaxPersistentConnections The maximum number of simultaneous persistent connections when sending.
    Type: xs:int    Default Value: 1
    MaxThreads The maximum number of threads that the component may consume.
    Type: xs:int    Default Value: 20
    MaxTransmissionBatchSize The maximum number of messages that can be sent in a single batch.
    Type: xs:int    Default Value: 1
    Other Defines a set of configuration settings to be used by the component.
    Type: xs:string    Default Value: ""
    RemoteFile The name of the destination file on the SSH server for uploading.
    Type: xs:string    Default Value: "%SourceFileName%"
    NOTE: This property must be specified.
    RemotePath The current path on the SSH server.
    Type: xs:string    Default Value: ""
    RuntimeLicense Specifies the component runtime license key.
    Type: xs:string    Default Value: ""
    SSHAcceptServerHostKey Instructs the component to accept the server host key that matches the supplied key.
    Type: Certificate    Default Value: null
    SSHAuthMode The type of authentication used by the component.
    Type: xs:int    Default Value: 2
    SSHCert The certificate to use for client authentication during the SSH handshake.
    Type: Certificate    Default Value: null
    NOTE: The digital id must have a private key associated with it.
    SSHCompressionAlgorithms A comma-separated list of compression algorithms allowed for this connection.
    Type: xs:string    Default Value: "none"
    SSHHost The address of the SSH host.
    Type: xs:string    Default Value: ""
    NOTE: This property must be specified.
    SSHPassword The password for SSH password-based authentication.
    Type: baf:Password    Default Value: ""
    SSHPort The port on the SSH server where the SSH service is running; by default, 22.
    Type: xs:int    Default Value: 22
    SSHUser The username for SSH authentication.
    Type: xs:string    Default Value: ""
    SSOAffiliate Specifies the name of the SSO Affiliate Application.
    Type: baf:SSOList    Default Value: ""
    Timeout A timeout for the component.
    Type: xs:int    Default Value: 60
    TransmitBatchMode How the transmitter processes batches.
    Type: xs:int    Default Value: 0
    TransportLog Tells the component where and how to report information about its operations.
    Type: Log    Default Value: null
    URI The Uniform Resource Identifier (URI) of the send port or receive location.
    Type: xs:string    Default Value: ""

  4. Click OK and OK again to save settings.

ConnectionLifetime Property (SCP Adapter)

Instructs the component whether or not to leave the connection to the server open.

Data Type

Enumeration

Possible Values

Automatic (0)
Per Batch (1)
Persisted (2)

Default Value

0

Remarks

This property is used when uploading batches of messages to a server that use the same connection properties. In order to minimize connection-related protocol overhead, connections may be persisted with various lifetimes:

Automatic (0 - default)The connection to the server will be established as needed per each message. When the message transmission is complete, the adapter will disconnect from the server.
Per Batch (1)During each batch, the connection to the server will be established as needed per each message. If a connection already exists to the server, that will be used as opposed to creating a new one. At the end of the batch, all such connections will be disconnected.
Persisted (2)Connections will be established as needed and stored. If a connection already exists for a server, that will be used as opposed to creating a new one. The connections will not be disconnected until the adapter is terminated by the BizTalk Message Engine.

This property is not available in the Receiver.

ErrorThreshold Property (SCP Adapter)

The maximum number of errors before the component shuts down.

Data Type

Integer

Default Value

5

Remarks

This property limits the number of errors that the adapter can incur before it shuts down and stops processing messages.

If set to 0 the adapter will never shutdown.

Note that if the operation completes successfully the current error count will be reset.

This property may be configured on the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Sender.

FileMask Property (SCP Adapter)

Indicates the type of files to download from the SSH server.

Data Type

String

Default Value

"*.*"

Remarks

This property will limit what kinds of files the adapter will download from the server. Only files matching the pattern specified in FileMask will be retrieved.

The following special characters are supported for pattern matching:

? Any single character.
* Any characters or no characters (e.g., C*t matches Cat, Cot, Coast, Ct).
[,-] A range of characters (e.g., [a-z], [a], [0-9], [0-9,a-d,f,r-z]).
\ The slash is ignored and exact matching is performed on the next character.

If these characters need to be used as a literal in a pattern, then they must be escaped by surrounding them with brackets []. Note: "]" and "-" do not need to be escaped. See below for the escape sequences:

CharacterEscape Sequence
? [?]
* [*]
[ [[]
\ [\]

For example, to match the value [Something].txt, specify the pattern [[]Something].txt.

This property is not available in the Sender.

Firewall Property (SCP Adapter)

A set of properties related to firewall access.

Data Type

Firewall

Remarks

This is a Firewall type property which contains fields describing the firewall through which the adapter will attempt to connect.

MaxBatchSize Property (SCP Adapter)

The maximum size, in MB, of the current batch (0 indicates no limit).

Data Type

Integer

Default Value

0

Remarks

This property limits the maximum amount of data the adapter can store before finalizing and processing the current batch to the number of bytes indicated.

Note: the default value, "0" indicates that there is no limit on the size of the batch. This value is not recommended for production environments as it may result in extremely large batches being held in memory before the adapter moves the data to the next stage of processing.

This property may be configured on the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Sender.

MaxFileCount Property (SCP Adapter)

The maximum number of files in the current batch (0 indicates no limit).

Data Type

Integer

Default Value

10

Remarks

This property places a limit on the number of files that can be transmitted in a single batch.

This property may be configured on the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Sender.

MaxFileSize Property (SCP Adapter)

The maximum size, in MB, of a file in the current batch (0 indicates no limit).

Data Type

Integer

Default Value

0

Remarks

This property limits the maximum size of any file in the current transmission batch to the number of bytes indicated.

Note: the default value, "0" indicates that there is no limit on the size of the batch. This value is not recommended for production environments as it may result in extremely large batches being held in memory before the adapter moves the data to the next stage of processing.

This property may be configured on the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Sender.

MaxPersistentConnections Property (SCP Adapter)

The maximum number of simultaneous persistent connections when sending.

Data Type

Integer

Default Value

1

Remarks

This setting specifies the maximum number of simultaneous persistent connections when sending.

The default value is 1, which limits the adapter to using one persistent connection for the adapter at any one time. This means when ConnectionLifetime is set to Persisted the send adapter will first check to see if an existing connection is present before transmitting data. In the case where a connection exists but another instance of the send port is using the connection the adapter will wait for the connection to become free. A value of 1 effectively serializes all communication for the send port through one persistent connection.

By setting a value greater than 1 a pool of persistent connections can be created. This allows multiple simultaneous persistent connections to be used. When the send adapter is active it will check to see if there are any existing connections. In the case where a connection exists but is being used by another instance of the send port it will attempt to create a new persistent connection. If creating a new persistent connection would exceed the limit specified in this setting the adapter will instead wait for a connection to become free. Setting this to a value greater than 1 allows multiple simultaneous connections to be made while still taking advantage of persistent connections to reduce the overhead of re-connecting.

Note: This only applies to the send adapter.

The default value is 1.

This property can only be configured through the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Receiver.

MaxThreads Property (SCP Adapter)

The maximum number of threads that the component may consume.

Data Type

Integer

Default Value

20

Remarks

This property limits the number of concurrent threads that the adapter may consume while completing its work.

This property can only be configured through the adapter's static handler property page in the BizTalk Server administration console.

MaxTransmissionBatchSize Property (SCP Adapter)

The maximum number of messages that can be sent in a single batch.

Data Type

Integer

Default Value

1

Remarks

This property controls the maximum size of an outbound message batch.

Note: be careful when modifying this property as it directly effects the efficiency of the transmit adapter. Setting MaxTransmissionBatchSize to a low value in an environment that requires transmission of large quantities of data will result in the adapter accumulating several small batches. If TransmitBatchMode is set to Parallel, this will result in the adapter transmitting many small batches at once and can put a heavy load on the processor.

Conversely, if TransmitBatchMode is set to Serial, setting MaxTransmissionBatchSize to a large value may result in long transmission delays as the adapter will wait on existing work to complete before accepting new messages from the BizTalk Message Engine. This is especially true when the adapter is transmitting large data.

This property can only be configured through the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Receiver.

Other Property (SCP Adapter)

Defines a set of configuration settings to be used by the component.

Data Type

String

Default Value

""

Remarks

The adapter accepts one or more configuration settings. Configuration settings are similar in functionality to properties, but they are rarely used. In order to avoid "polluting" the property namespace of the adapter, access to these internal properties is provided through the Other property.

The Other property may be set to one or more configuration settings (name/value pairs). Set one setting per line. For example: configname1=value1 configname2=value2

PersistentConnection Property (SCP Adapter)

Instructs the component whether to keep the connection to the server open.

Data Type

Boolean

Default Value

false

Remarks

If set to true, the adapter will first attempt to use an existing connection. If no such connection exists, it will create a new connection. When the adapter completes, it will persist the connection so that the adapter will reuse it during the next polling interval. Setting this property to true can improve performance if you are polling very frequently.

PollingInterval Property (SCP Adapter)

The amount of time, in seconds, between download attempts.

Data Type

Integer

Default Value

60

Remarks

The adapter will wait for the number of seconds indicated before attempting another download.

This property is not available in the Sender.

ReceivedFileName Property (SCP Adapter)

The name of the remote file received by the SCP component.

Data Type

String

Default Value

""

Remarks

This is the filename returned by the server.

This value is also placed in the File.ReceivedFileName and the FTP.ReceivedFileName context properties. This is to ensure compatibility with other adapters that poll those context properties when filling out macros such as %SourceFileName%.

This property is not available in the Sender.

ReceivedFilePath Property (SCP Adapter)

The remote path of the received file.

Data Type

String

Default Value

""

Remarks

This property holds the remote path of the received file. It identifies the path on the server from which the file was downloaded. In most cases this will be identical to RemotePath.

In the case where RecursiveMode is set to true this value can be used to preserve the remote directory structure.

This property is not available in the Sender.

ReceivedFileSize Property (SCP Adapter)

The size of the remote file received by the SCP component.

Data Type

Integer

Default Value

0

Remarks

This value contains the size of the remote file being received by the SCP adapter. It can be read from the context of a message being received by an SCP adapter receive location.

This property is not available in the Sender.

ReceivedFileSSHUser Property (SCP Adapter)

The SSH user name used by the SCP component when downloading the remote file.

Data Type

String

Default Value

""

Remarks

This value contains the SSHUser used by the SCP adapter to authenticate before downloading the remote file. It can be read from the context of a message being received by an SCP adapter receive location.

This property is not available in the Sender.

RemoteFile Property (SCP Adapter)

The name of the destination file on the SSH server for uploading.

Data Type

String

Default Value

"%SourceFileName%"

Remarks

The RemoteFile is either an absolute file path, or a relative path based on RemotePath.

This property is not available in the Receiver.

RemotePath Property (SCP Adapter)

The current path on the SSH server.

Data Type

String

Default Value

""

Remarks

The RemotePath can be used to set the working directory by setting it to either an absolute directory path or a path relative to the initial remote directory when the adapter connects to the SSH server.

RequeueEndpoints Property (SCP Adapter)

Whether to requeue receive endpoints if the polling interval has not been reached.

Data Type

Boolean

Default Value

false

Remarks

This setting controls whether receive endpoints are requeued for later processing if the polling interval has not yet been reached. When this setting is set to No (default) each thread will block until the polling interval for the corresponding receive location is reached. If there exist more active receive locations than MaxThreads it is possible for some threads to block the execution of others since they may be waiting for a polling interval.

When this setting is set to Yes if the polling interval has not been reached the thread will not block until the polling interval is reached, and instead the endpoint will be requeued to be processed later. This lets subsequent endpoints in the queue to be processed.

If MaxThreads is set to a low value and there are a larger number of receive locations setting this to Yes will help assure that polling intervals are respected and receive locations poll in a timely manner.

The default value is No.

This property can only be configured through the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Sender.

RuntimeLicense Property (SCP Adapter)

Specifies the component runtime license key.

Data Type

String

Default Value

""

Remarks

You can use the RuntimeLicense property to set the runtime key for the adapter license.

This property may be configured on the adapter's static handler property page in the BizTalk Server administration console.

SSHAcceptServerHostKey Property (SCP Adapter)

Instructs the component to accept the server host key that matches the supplied key.

Data Type

Certificate

Remarks

If the host key that will be used by the server is known in advance, this property may be set to accept the expected key. If you are using the fingerprint, you may supply it to the SSHAcceptServerHostKeyFingerPrint setting by HEX encoding the values in the form "0a:1b:2c:3d". If this property is not set the server will not be authenticated, and the connection will be refused by the client.

Note: You may also set the Accept Any field to Yes without opening the certificate selection dialog to force the adapter to unilaterally authenticate any server during the security handshake. It is strongly recommended that you use this only for testing purposes. Set the LogMode to Info to cause the adapter to report the server's credentials to Location.

SSHAuthMode Property (SCP Adapter)

The type of authentication used by the component.

Data Type

Enumeration

Possible Values

None (0)
Multi Factor (1)
Password (2)
Public Key (3)
Keyboard Interactive (4)
GSSAPIWith Mic (5)

Default Value

2

Remarks

SSHAuthMode controls how the adapter attempts to authenticate when connecting to the SSHHost. The following authentication methods are available:

NoneThe adapter will attempt anonymous authentication.
Multi-FactorThe adapter will attempt as many authentication steps as the server requires using whatever credentials it has available.
PasswordThe adapter will send the SSHPassword to the server.
Public KeyThe adapter will send the SSHCert to the server;
Keyboard-InteractiveThe adapter will perform SSH keyboard-interactive authentication, responding automatically to the server's authentication prompts. It will supply the value of SSHPassword as the response to the "password" prompt. Note: this method is not truly keyboard-interactive, and the adapter may not recognize all prompts supplied by the server. It should be used only when the SSHHost cannot be configured to authenticate the SSHUser via more easily automated methods such as Password or Public Key.
GSSAPIWithMicThis allows the adapter to attempt Kerberos authentication using the GSSAPI-WITH-MIC scheme. The client will try Kerberos authentication using the value of SSHUser (single sign-on), or if SSHPassword is specified as well, it will try Kerberos authentication with alternate credentials.

SSHCert Property (SCP Adapter)

The certificate to use for client authentication during the SSH handshake.

Data Type

Certificate

Remarks

This property is used to assign a specific certificate for SSH client authentication.

This field is used to set a Private Key Certificate.

Private key certificates may be loaded from the registry, from files in PKCS#12 format, or from a PEM file format. If you click on the ellipses, a certificate selection dialog will open. To select a private key from the system registry, select the System Store tab or the User Store tab, and highlight the appropriate registry store. The list of certificates which have private keys will be shown below.

To select a private key certificate from a file in PKCS#12 format, select the PFX Store tab. The browse button can be used to examine the file system for PKCS#12 (.pfx or .p12) certificates. If you wish to examine the certificate, provide the password in the field provided and click on the Open button to examine the file store for certificates present. To load a certificate from PEM files, select the PEM tab. Like the PFX file selection, you can specify the password and click the Open button to examine the certificates in the PEM store, or you may paste any PEM data stored in memory.

Regardless of how you selected the certificate, once you hit the OK button, the adapter will attempt to verify that certificate selection. If successful, the subject of the certificate will be displayed in the property field. If the adapter was not able to verify the selection, a dialog box will appear instead detailing the verification error.

SSHCompressionAlgorithms Property (SCP Adapter)

A comma-separated list of compression algorithms allowed for this connection.

Data Type

String

Default Value

"none"

Remarks

This list is used for both directions: client to server and server to client. When negotiating algorithms, each side sends a list of all algorithms it supports or allows. The algorithm chosen for each direction is the first algorithm to appear in the sender's list that the receiver supports, so it is important to list multiple algorithms in preferential order. If no algorithm can be agreed upon, the adapter will raise an error and the connection will be aborted.

SSHCompressionAlgorithms must be set to a comma-separated list containing at least one of the following values:

zlibZlib compression is allowed for this connection.
noneNo compression is allowed for this connection.

SSHHost Property (SCP Adapter)

The address of the SSH host.

Data Type

String

Default Value

""

Remarks

The SSHHost property specifies the IP address (IP number in dotted internet format) or Domain Name of the remote host. It is set before a connection is attempted and cannot be changed once a connection is established.

If the SSHHost property is set to a Domain Name, a DNS request is initiated, and upon successful termination of the request, the SSHHost property is set to the corresponding address. If the search is not successful, an error is logged.

SSHPassword Property (SCP Adapter)

The password for SSH password-based authentication.

Data Type

Password

Default Value

""

Remarks

SSHPassword specifies the password which is used to authenticate the client to the SSH server.

SSHPort Property (SCP Adapter)

The port on the SSH server where the SSH service is running; by default, 22.

Data Type

Integer

Default Value

22

Remarks

The SSHPort specifies a service port on the SSH host to connect to.

SSHUser Property (SCP Adapter)

The username for SSH authentication.

Data Type

String

Default Value

""

Remarks

SSHUser specifies the username which is used to authenticate the client to the SSH server. This property is required.

SSOAffiliate Property (SCP Adapter)

Specifies the name of the SSO Affiliate Application.

Data Type

String

Default Value

""

Remarks

This property allows the adapter to load credentials from an Enterprise Single Sign-On secret server.

TempPath Property (SCP Adapter)

A temporary local directory where data can be stored before the component processes it.

Data Type

String

Default Value

""

Remarks

This property indicates a temporary directory where the adapter can store any data before the adapter processes it. If TempPath is empty, the adapter will receive all data to memory. If set, the adapter will generate and write all inbound data to a temporary file in the specified directory.

Once the file is submitted, the adapter will handle closing the file stream and deleting the temporary file. However, if the adapter is shut down during a transfer some temporary files may be left in the directory. To ensure optimal performance, server administrators should check the directory regularly and remove old or extraneous files.

This property accepts the "%TEMP%" macro, which will be replaced with the default system temporary directory at runtime. Note: by default, this property is empty and the adapter will use memory streams to store all inbound data before submitting it. It is recommended that you use a temporary directory when downloading large batches or batches containing large files to alleviate potential increased memory requirements.

This property is not available in the Sender.

Timeout Property (SCP Adapter)

A timeout for the component.

Data Type

Integer

Default Value

60

Remarks

If the Timeout property is set to 0, all operations will run uninterrupted until successful completion, or an error condition is encountered.

If Timeout is set to a positive value, the adapter will wait for the operation to complete before returning control.

If Timeout expires, and the operation is not yet complete, the adapter fails with an error.

Please note that by default, all timeouts are inactivity timeouts, i.e. the timeout period is extended by Timeout seconds when data is successfully sent or received.

Optionally, the behavior of the adapter may be changed to absolute timeouts, i.e. the adapter will wait for a maximum of Timeout seconds since the beginning of the operation, without extending the timeout period during communications.

This behavior is controlled by the AbsoluteTimeout configuration setting.

The default value for the Timeout property is 60 (seconds).

TransmitBatchMode Property (SCP Adapter)

How the transmitter processes batches.

Data Type

Enumeration

Possible Values

Parallel (0)
Serial (1)

Default Value

0

Remarks

This property controls how the transmitter processes message batches:

ParallelThe adapter will process however many batches the BizTalk Message Engine sends it.

The number of maximum concurrent batches may be controlled by the MaxThreads property.

SerialThe adapter will queue batches from the BizTalk Message Engine and process them one at a time.

This property can only be configured through the adapter's static handler property page in the BizTalk Server administration console.

This property is not available in the Receiver.

TransportLog Property (SCP Adapter)

Tells the component where and how to report information about its operations.

Data Type

Log

Remarks

This is a Log type property which contains fields describing how and where the adapter will record information about its execution.

This property may be configured on the adapter's static handler property page in the BizTalk Server administration console.

URI Property (SCP Adapter)

The Uniform Resource Identifier (URI) of the send port or receive location.

Data Type

String

Default Value

""

Remarks

This property specifies a URI for the send port or receive location. Setting this property is optional.

By default the adapter will automatically generate a URI. You may choose to specify your own value here to be used in place of the generated URI.

If this value is specified it must begin with the correct prefix, as seen in the default value.

Certificate Type

The digital certificate being used.

Remarks

This type describes the current digital certificate. The certificate may be a public or private key. The fields are used to identify or select certificates.

Fields

Store
String

The name of the certificate store for the client certificate.

The StoreType field specifies the type of the certificate store specified by Store. If the store is password protected, specify the password in StorePassword.

Store is used in conjunction with the Subject field in order to specify client certificates. If Store has a value, and Subject is set, a search for a certificate is initiated. Please refer to the Subject field for details.

Designations of certificate stores are platform-dependent.

The following are designations of the most common User and Machine certificate stores in Windows:

MYA certificate store holding personal certificates with their associated private keys.
CACertifying authority certificates.
ROOTRoot certificates.
SPCSoftware publisher certificates.

In Java, the certificate store normally is a file containing certificates and optional private keys.

When the certificate store type is PFXFile, this property must be set to the name of the file. When the type is PFXBlob, the property must be set to the binary contents of a PFX file (i.e. PKCS12 certificate store).

If the provider is OpenSSL, the certificate store is a file containing a certificate and a private key. This property must be set to the name of the file.

StorePassword
String

If the certificate store is of a type that requires a password, this property is used to specify that password in order to open the certificate store.

StoreType
CertStoreTypes

The type of certificate store for this certificate.

The adapter supports both public and private keys in a variety of formats. When the cstAuto value is used the adapter will automatically determine the type. This field can take one of the following values:

0 (cstUser - default)For Windows, this specifies that the certificate store is a certificate store owned by the current user. Note: this store type is not available in Java.
1 (cstMachine)For Windows, this specifies that the certificate store is a machine store. Note: this store type is not available in Java.
2 (cstPFXFile)The certificate store is the name of a PFX (PKCS12) file containing certificates.
3 (cstPFXBlob)The certificate store is a string (binary or base64-encoded) representing a certificate store in PFX (PKCS12) format.
4 (cstJKSFile)The certificate store is the name of a Java Key Store (JKS) file containing certificates. Note: this store type is only available in Java.
5 (cstJKSBlob)The certificate store is a string (binary or base64-encoded) representing a certificate store in Java Key Store (JKS) format. Note: this store type is only available in Java.
6 (cstPEMKeyFile)The certificate store is the name of a PEM-encoded file that contains a private key and an optional certificate.
7 (cstPEMKeyBlob)The certificate store is a string (binary or base64-encoded) that contains a private key and an optional certificate.
8 (cstPublicKeyFile)The certificate store is the name of a file that contains a PEM- or DER-encoded public key certificate.
9 (cstPublicKeyBlob)The certificate store is a string (binary or base64-encoded) that contains a PEM- or DER-encoded public key certificate.
10 (cstSSHPublicKeyBlob)The certificate store is a string (binary or base64-encoded) that contains an SSH-style public key.
11 (cstP7BFile)The certificate store is the name of a PKCS7 file containing certificates.
12 (cstP7BBlob)The certificate store is a string (binary) representing a certificate store in PKCS7 format.
13 (cstSSHPublicKeyFile)The certificate store is the name of a file that contains an SSH-style public key.
14 (cstPPKFile)The certificate store is the name of a file that contains a PPK (PuTTY Private Key).
15 (cstPPKBlob)The certificate store is a string (binary) that contains a PPK (PuTTY Private Key).
16 (cstXMLFile)The certificate store is the name of a file that contains a certificate in XML format.
17 (cstXMLBlob)The certificate store is a string that contains a certificate in XML format.
18 (cstJWKFile)The certificate store is the name of a file that contains a JWK (JSON Web Key).
19 (cstJWKBlob)The certificate store is a string that contains a JWK (JSON Web Key).
20 (cstSecurityKey)The certificate is present on a physical security key accessible via a PKCS11 interface.

To use a security key the necessary data must first be collected using the CERTMGR adapter. The ListStoreCertificates method may be called after setting CertStoreType to cstSecurityKey, CertStorePassword to the PIN, and CertStore to the full path of the PKCS11 dll. The certificate information returned in the CertList event's CertEncoded parameter may be saved for later use.

When using a certificate, pass the previously saved security key information as the Store and set StorePassword to the PIN.

Code Example: SSH Authentication with Security Key certmgr.CertStoreType = CertStoreTypes.cstSecurityKey; certmgr.OnCertList += (s, e) => { secKeyBlob = e.CertEncoded; }; certmgr.CertStore = @"C:\Program Files\OpenSC Project\OpenSC\pkcs11\opensc-pkcs11.dll"; certmgr.CertStorePassword = "123456"; //PIN certmgr.ListStoreCertificates(); sftp.SSHCert = new Certificate(CertStoreTypes.cstSecurityKey, secKeyBlob, "123456", "*"); sftp.SSHUser = "test"; sftp.SSHLogon("myhost", 22);

21 (cstBCFKSFile)The certificate store is the name of a file that contains a BCFKS (Bouncy Castle FIPS Key Store). Note: this store type is only available in Java and .NET.
22 (cstBCFKSBlob)The certificate store is a string (binary or base64-encoded) representing a certificate store in BCFKS (Bouncy Castle FIPS Key Store) format. Note: this store type is only available in Java and .NET.
99 (cstAuto)The store type is automatically detected from the input data. This setting may be used with both public and private keys and can detect any of the supported formats automatically.

Subject
String

The subject of the certificate used for client authentication.

When this property is set, a search is performed in the current certificate store certificate with matching subject.

If an exact match is not found, the store is searched for subjects containing the value of the property.

When setting the property to a partial subject, CN= should be omitted. For example, the following code would find the certificate with subject CN=Test Certificate, OU=People, C=US

Example (Searching with partial subject)

Control.CertSubject = "Test"

If a match is not found, the property is set to an empty string, and no certificate is selected.

The special value "*" picks a random certificate in the certificate store.

If a matching certificate is found, Subject is set to the full subject of the matching certificate.

Thumbprint
String

The thumbprint of the certificate.

This field is used to specify the thumbprint of the certificate. When there are multiple certificates in the store that have the same subject, the thumbprint will be used to distinguish between them.

Constructors

Constructors are only relevant when configuring adapters in orchestrations.

public Certificate();

Creates a Certificate instance whose properties can be set.

public Certificate(string certificateFile);

Opens CertificateFile and reads out the contents as an X509 public key.

public Certificate(byte[] certificateData);

Parses CertificateData as an X509 public key.

public Certificate(CertStoreTypes certStoreType, string store, string storePassword, string subject);

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a file containing the certificate store. StorePassword is the password used to protect the store. After the store has been successfully opened, the constructor will attempt to find the certificate identified by Subject . This can be either a complete or a substring match of the X509 certificate's subject Distinguished Name (DN).

public Certificate(CertStoreTypes certStoreType, string store, string storePassword, byte[] encoded);

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a file containing the certificate store. StorePassword is the password used to protect the store. After the store has been successfully opened, the constructor will load Encoded as an X509 certificate and search the opened store for a corresponding private key.

public Certificate(CertStoreTypes certStoreType, byte[] storeBlob, string storePassword, string subject);

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a string (binary- or base64-encoded) containing the certificate store. StorePassword is the password used to protect the store. After the store has been successfully opened, the constructor will attempt to find the certificate identified by Subject . This can be either a complete or a substring match of the X509 certificate's subject Distinguished Name (DN).

public Certificate(CertStoreTypes certStoreType, byte[] storeBlob, string storePassword, byte[] encoded);

CertStoreType identifies the type of certificate store to use. See StoreType for descriptions of the different certificate stores. Store is a string (binary- or base64-encoded) containing the certificate store. StorePassword is the password used to protect the store. After the store has been successfully opened, the constructor will load Encoded as an X509 certificate and search the opened store for a corresponding private key.

Firewall Type

The firewall the component will connect through.

Remarks

When connecting through a firewall, this type is used to specify different properties of the firewall such as the firewall Host and the FirewallType.

Fields

AutoDetect
Boolean

Tells the adapter whether or not to automatically detect and use firewall system settings, if available.

FirewallType
FirewallTypes

Determines the type of firewall to connect through. The applicable values are the following:

fwNone (0)No firewall (default setting).
fwTunnel (1)Connect through a tunneling proxy. Port is set to 80.
fwSOCKS4 (2)Connect through a SOCKS4 Proxy. Port is set to 1080.
fwSOCKS5 (3)Connect through a SOCKS5 Proxy. Port is set to 1080.

Host
String

Name or IP address of firewall (optional). If a Host is given, requested connections will be authenticated through the specified firewall when connecting.

If the Host field is set to a Domain Name, a DNS request is initiated. Upon successful termination of the request, the Host field is set to the corresponding address. If the search is not successful, an error is returned.

Password
String

A password if authentication is to be used when connecting through the firewall. If Host is specified, the User and Password fields are used to connect and authenticate to the given firewall. If the authentication fails, a trappable error is fired.

Port
Integer

The TCP port for the firewall Host. See the description of the Host field for details.

Note that the Port is set automatically when FirewallType is set to a valid value. See the description of the FirewallType field for details.

User
String

A user name if authentication is to be used connecting through a firewall. If the Host is specified, the User and Password fields are used to connect and authenticate to the given Firewall. If the authentication fails, a trappable error is fired.

Constructors

Constructors are only relevant when configuring adapters in orchestrations.

public Firewall();

Log Type

A log where the component will record information about its operations.

Remarks

This describes how and where the adapter will record information describing its execution.

Fields

Location
String

This field describes the location where the logging information is to be written.

If the EventLog LogType has been chosen, this field must contain the name of the Event Log to which the information should be written. The default value for this field is "Application". If a value other than "Application" is set the computer must be restarted for the change to take effect. Note that the same event log must be used for all send ports and receive locations that use the same adapter.

If the File LogType has been chosen, this field must contain the location of the file to write logging information to on the file system.

The adapter also supports logging to files based on the current date and time. This allows for log files to be organized by days, months, or other intervals as specified. When specifying a log filename include a valid .NET date and time format string within the < and > characters. For instance C:\logs\sftp_<yyyyMMdd>.log or C:\logs\as2_<yyyyMMdd>T<hhmm>.log.

LogMode
LogModes

This field controls what information the adapter logs. The possible values have the following affect on the adapter's behavior:

VerboseThe adapter will report all information regarding the transport.
Info The adapter will report all major operations, as well as all warnings and errors.
WarningThe adapter will report any conditions that could result in unpredictable behavior as well as errors.
ErrorThe adapter will report all errors that prevent normal operations from completing.
FatalThe adapter will report only serious errors that cause the adapter to completely stop functioning.

LogType
LogTypes

This property controls where the adapter will log the information. The possible values have the following affect on the adapter's behavior:

NoneThe adapter will not report any logging information.
EventLogThe adapter will report all logging information to the event log. The specific event log must be defined in the Location field when this type is selected.
FileThe adapter will report all logging information to a file. The desired file must be specified in the Location field when this type has been selected.

Constructors

Constructors are only relevant when configuring adapters in orchestrations.

public Log();
public Log(LogTypes logType, string location, LogModes logMode);

Config Settings (SCP Adapter)

The adapter accepts one or more of the following configuration settings. Configuration settings are similar in functionality to properties, but they are rarely used. In order to avoid "polluting" the property namespace of the adapter, access to these internal properties is provided through the Other property.

SCP Config Settings

Download:   If set to true, the send adapter will download files instead of upload.

This setting is used to download multiple files using the send adapter. It is only applicable to the send adapter. In situations where you want to initiate the download of files instead of using a receive adapter you can configure the send adapter to download the files. It is similar in use to DownloadSingleFile.

To do this you can not use a solicit response port. You must use a one way send port. In this case set the LocalFile setting to the directory to which you'd like to download the files.

DownloadSingleFile:   If set to true, the send adapter will download a file instead of upload.

This setting is used to download a file from an orchestration using the send adapter. It is only applicable to the send adapter. In situations where you want to initiate the download of a file instead of using a receive adapter you can configure the send adapter to download the file.

In this case the adapter should be used as a solicit response adapter. Because a solicit response port can return only one message, you can only download one file at a time with the SFTP, SCP, FTP, and WebDAV send ports. To do this you'll need to set the DownloadSingleFile configuration setting to true. For instance: Message_2 = Message_1; Message_2(nsoftware.BizTalk.SFTP.SSHUser) = "test"; Message_2(nsoftware.BizTalk.SFTP.SSHPassword) = "test"; Message_2(nsoftware.BizTalk.SFTP.SSHHost) = "server"; Message_2(nsoftware.BizTalk.SFTP.SSHAcceptServerHostKeyAcceptAny) = true; Message_2(nsoftware.BizTalk.SFTP.RemotePath) = "temp"; Message_2(nsoftware.BizTalk.SFTP.RemoteFile) = "test.txt"; Message_2(nsoftware.BizTalk.SFTP.Other) = "DownloadSingleFile=true";

Note: You can also set DeleteAfterDownload in the Other property for FTP, SFTP, and WebDAV transfers to delete the file on the server once the download is complete. DeleteAfterDownload is not applicable to SCP. This can be done by setting one configuration setting per line in the Other property: Message_2(nsoftware.BizTalk.SFTP.Other) = "DownloadSingleFile=true\r\nDeleteAfterDownload=true";

It is also possible to download multiple files with the send adapters. To do this you can not use a solicit response port. You must use a one way send port. In this case set the LocalFile setting to the directory to which you'd like to download the files and set Download to true.

FilePermissions:   Specifies the permissions of a file to be set after a successful upload.

This may be set to an octal value representing the permissions of a file to be set after a successful upload. For example: FilePermissions=0777 Note: When using the SCP adapter this must be a 4 digit value. The SFTP adapter will accept a 3 digit value.

KeyRenegotiationThreshold:   Sets the threshold for the SSH Key Renegotiation.

This property allows you to specify the threshold, in the number of bytes, for the SSH Key Renegotiation. The default value for this property is set to 1 GB.

Example (for setting the threshold to 500 MB): SSHComponent.Config("KeyRenegotiationThreshold=524288000")

LocalFile:   Specifies the local file or file mask when uploading.

This setting overrides the overrides the default behavior of the adapter, causing it to ignore the normal message data and upload the file indicated. Likewise, the parsed local filename is used instead of the value in the RemoteFile property.

This may be set to a FileMask value when uploading and RecursiveMode is set to True.

LogSSHPackets:   If True, detailed SSH packet logging is performed.

This setting can be enabled to assist in debugging. When set to True the adapter will include detailed information about the SSH level packets in the log. The default value is False.

RecursiveMode:   If set to true the adapter will recursively upload or download files.

When a filemask is specified in LocalFile (sending) or FileMask (receiving) this setting specifies if sub-directories and files are transferred as well. By default this value is False and only files in the specified directory will be transferred. If set to true recursion will be used to transfer all child folders and files.

When sending, LocalFile should contain the path and filemask of a location on disk from which files will be uploaded. For instance "c:\files\*.txt".

When receiving, the ReceivedFilePath message context property is populated and provides the remote path from which the file was downloaded. Note that the server may not always return the expected files depending on the FileMask specified. A value of "*" should always work, however more complex filemask values may not be handled by the server as expected.

ServerResponseWindow:   The time to wait for a server response in milliseconds.

After an operation is complete the server may still return an error. This setting controls the amount of time the adapter will wait for an error to be returned. This value is specified in milliseconds. The default value is "20".

SSHAcceptServerHostKeyFingerPrint:   Instructs the adapter to accept the server's host key with this fingerprint.

This may be set to a comma-delimited collection of 16-byte MD5 fingerprints that should be accepted as the host's key. You may supply it by HEX encoding the values in the form "0a:1b:2c:3d". Example: SSHAcceptServerHostKeyFingerprint=0a:1b:2c:3d

SSHEncryptionAlgorithms:   A comma-separated list containing all allowable compression algorithms.

During the SSH handshake, this list will be used to negotiate the encryption algorithm to be used between the client and server. This list is used for both directions: client to server and server to client.

At least one supported algorithm must appear in this list. The following encryption algorithms are supported by the component:

aes256-cbc256-bit AES encryption in CBC mode
aes192-cbc192-bit AES encryption in CBC mode
aes128-cbc128-bit AES encryption in CBC mode
3des-cbc192-bit (3-key) triple DES encryption in CBC mode
aes256-ctr256-bit AES encryption in CTR mode
aes192-ctr192-bit AES encryption in CTR mode
aes128-ctr128-bit AES encryption in CTR mode
3des-ctr192-bit (3-key) triple DES encryption in CTR mode
cast128-cbcCAST-128 encryption
blowfish-cbcBlowfish encryption
arcfourARC4 encryption
arcfour128128-bit ARC4 encryption
arcfour256256-bit ARC4 encryption
aes256-gcm@openssh.com256-bit AES encryption in GCM mode.
aes128-gcm@openssh.com128-bit AES encryption in GCM mode.

The default value is "aes256-ctr,aes192-ctr,aes128-ctr,aes256-cbc,aes192-cbc,aes128-cbc,3des-ctr,3des-cbc,blowfish-cbc,arcfour256,arcfour128,arcfour,cast128-cbc,aes256-gcm@openssh.com,aes128-gcm@openssh.com".

SSHKeyExchangeAlgorithms:   Specifies the supported key exchange algorithms.

This may be used to specify the list of supported Key Exchange algorithms used during SSH negotiation. The value should contain a comma separated list of algorithms. Supported algorithms are:

  • curve25519-sha256
  • curve25519-sha256@libssh.org
  • diffie-hellman-group1-sha1
  • diffie-hellman-group14-sha1
  • diffie-hellman-group14-sha256
  • diffie-hellman-group16-sha512
  • diffie-hellman-group18-sha512
  • diffie-hellman-group-exchange-sha256
  • diffie-hellman-group-exchange-sha1
  • ecdh-sha2-nistp256
  • ecdh-sha2-nistp384
  • ecdh-sha2-nistp521
The default value is: curve25519-sha256,curve25519-sha256@libssh.org,diffie-hellman-group-exchange-sha256,diffie-hellman-group14-sha256,diffie-hellman-group16-sha512,diffie-hellman-group18-sha512,ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1.
SSHMacAlgorithms:   Specifies the supported Mac algorithms.

This may be used to specify an alternate list of supported Mac algorithms used during SSH negotiation. This also specifies the order in which the Mac algorithms are preferred. The value should contain a comma separated list of algorithms. Supported algorithms are:

  • hmac-sha1
  • hmac-md5
  • hmac-sha1-96
  • hmac-md5-96
  • hmac-sha2-256
  • hmac-sha2-256-96
  • hmac-sha2-512
  • hmac-sha2-512-96
  • hmac-ripemd160
  • hmac-ripemd160-96
  • hmac-sha2-256-etm@openssh.com
  • hmac-sha2-512-etm@openssh.com
The default value is hmac-sha2-256,hmac-sha2-512,hmac-sha1,hmac-md5,hmac-ripemd160,hmac-sha1-96,hmac-md5-96,hmac-sha2-256-96,hmac-sha2-512-96,hmac-ripemd160-96,hmac-sha2-256-etm@openssh.com,hmac-sha2-512-etm@openssh.com.
SSHPublicKeyAlgorithms:   Specifies the supported public key algorithms for the server's public key.

This setting specifies the allowed public key algorithms for the server's public key. This list controls only the public key algorithm used when authenticating the server's public key. This list has no bearing on the public key algorithms that can be used by the client when performing public key authentication to the server. The default value is ssh-ed25519,ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,rsa-sha2-256,rsa-sha2-512,ssh-rsa,ssh-dss,x509v3-sign-rsa,x509v3-sign-dss.

This setting specifies a list of signature algorithms that may be used when authenticating to the server using public key authentication. This applies only when public key authentication is performed by the client.

The setting should be a comma separated list of algorithms. At runtime the adapter will evaluate the specified algorithms and if the algorithm is applicable to the certificate specified in SSHCert it will be used. If the algorithm is not applicable the adapter will evaluate the next algorithm. Possible values are:

  • ssh-rsa
  • rsa-sha2-256
  • rsa-sha2-512
  • ssh-dss
  • ecdsa-sha2-nistp256
  • ecdsa-sha2-nistp384
  • ecdsa-sha2-nistp521
  • ssh-ed25519
  • x509v3-sign-rsa
  • x509v3-sign-dss

The default value in Windows is ssh-rsa,rsa-sha2-256,rsa-sha2-512,ssh-dss,ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,ssh-ed25519.

rsa-sha2-256 and rsa-sha2-512 notes

The adapter will query the server for supported algorithms when connecting. If the server indicates support for rsa-sha2-256 or rsa-sha2-512 and the algorithm is present in the list defined by this setting (as in the default value), that algorithm will be used instead of ssh-rsa even when ssh-rsa appears first in the list.

For the rsa-sha2-256 and rsa-sha2-512 algorithms to be automatically preferred the server must support the ext-info-c mechanism. In practice, older servers do not support this and in that case ssh-rsa will be used since it appears first in the list. Newer servers do support this mechanism and in that case rsa-sha2-256 or rsa-sha2-512 will be used even though it appears after ssh-rsa.

This behavior has been carefully designed to provide maximum compatibility while automatically using more secure algorithms when connecting to servers which support them.

General Config Settings

AbsoluteTimeout:   Determines whether timeouts are inactivity timeouts or absolute timeouts.

If AbsoluteTimeout is set to True, any method which does not complete within Timeout seconds will be aborted. By default, AbsoluteTimeout is False, and the timeout is an inactivity timeout.

LocalHost:   The name of the local host or user-assigned IP interface through which connections are initiated or accepted.

The LocalHost configuration contains the name of the local host as obtained by the Gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multihomed hosts (machines with more than one IP interface) setting LocalHost to the value of an interface will make the adapter initiate connections (or accept in the case of server adapters) only through that interface.

If the adapter is connected, the LocalHost configuration shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multihomed hosts (machines with more than one IP interface).

TcpNoDelay:   Whether or not to delay when sending packets.

When true, the socket will send all data that is ready to send at once. When false, the socket will send smaller buffered packets of data at small intervals. This is known as the Nagle algorithm.

By default, this config is set to false.

UseInternalSecurityAPI:   Tells the adapter whether or not to use the system security libraries or an internal implementation.

By default the adapter will use the system security libraries to perform cryptographic functions where applicable. When set to False calls to unmanaged code will be made. In certain environments this is not desirable. To use a completely managed security implementation set this setting to True. Setting this to True tells the adapter to use the internal implementation instead of using the system's security API.

Note: This setting is static. The value set is applicable to all adapters used in the application.

When this value is set the product's system DLL is no longer required as a reference, as all unmanaged code is stored in that file.

Supported Macros

The adapter also supports the following Macros. These values are not case sensitive and would be supplied to a property in the form %MacroName%.

TempThis is resolved to the full path to the system's temporary directory.
MessageIDGlobally unique identifier (GUID) of the message in BizTalk Server.
SourceFileNameThe original file name. This includes the extension and excludes the file path, for example, Sample.xml
SourceFileNameNoExtThe original file name without the extension or file path, for example, Sample
RemoteFileNameThe name of the file as it was uploaded to the remote server. This includes the extension and excludes the file path, for example, Sample.xml. Valid only for AS3, FTP, and SFTP Send Adapters.
DestinationPartyName of the destination party.
DestinationPartyQualifierQualifier of the destination party.
SourcePartyName of the source party.
SourcePartyQualifierQualifier of the source party.
DateTime:CustomFormatThis special value allows you to specify your own custom time format. For instance DateTime:yyyy would be resolved to the 4 digit year.
DateThe date format yyyy-MM-dd.
DateTimeThe date format yyyy-MM-ddThhmmss.
TimeThe date format hhmmss.
DateTime_BTS2000The date format yyyyMMddhhmmssf.
DateTime.TZThe date format yyyy-MM-ddThhmmsszzz.
Time.TZThe date format hhmmsszzz.
Property#<Schema>#<Name>This special value allows you to include a property from the incoming message. For instance "PROPERTY#http://schemas.microsoft.com/BizTalk/2003/system-properties#ReceivePortName" would resolve to the ReceivePortName property of the message.

Copyright (c) 2022 /n software inc. - All rights reserved.
/n software Adapters for BizTalk - Version 22.0 [Build 8376]