Rshell Class

Properties Methods Events Config Settings Errors

The remote shell (rshell) class is used to execute commands on a remote Unix machine using the rshell mechanism.

Syntax

ipworks.rshell()

Remarks

The rshell class allows remote execution of commands on UNIX hosts, or on any other system with the rshell interface. Using the class is simple. The destination is specified by the RemoteHost property, and the login information is given by the LocalUser and RemoteUser properties. You can call the Execute method with the Command to execute as a parameter. You also can set the Command property to the command that you would like to execute for identical results. Further input can be supplied to the command by assigning data to the Text parameter of the Send method or by using the Stdin property.

The output of the command is returned through the Stdout event. If an error occurs on the protocol level, the error message can be found in the ErrorMessage property. Errors that occur during command execution (the stderr stream) are given by the Stderr event.

Note: To be able to successfully use the class, the remote host must be set up to allow execution of commands via rshell from the machine the class runs on.

Property List

The following is the full list of the properties of the class with short descriptions. Click on the links for further details.


BytesSent	This property includes the number of bytes actually sent after an assignment to Stdin.
Connected	This shows whether the class is connected.
EOF	If this property is True, the connection has closed, and no buffered data are available.
EOL	This property is used to break the stdout data stream into chunks separated by its value.
ErrEOL	This property is used to break the stderr data stream into chunks separated by its value.
ErrorMessage	This property includes the error message that is returned when any of the steps before command execution fail.
Firewall	A set of properties related to firewall access.
LocalHost	The name of the local host or user-assigned IP interface through which connections are initiated or accepted.
LocalPort	This property includes the Transmission Control Protocol (TCP) port in the local host where the class binds.
LocalUser	This property includes the identifier of the user on the local machine.
RemoteHost	This property includes the address of the remote host. Domain names are resolved to IP addresses.
RemotePort	This property includes the remote shell service port (default is 514).
RemoteUser	This property includes the Id of the user on the remote host.
Stderr	This property returns the standard error (stderr) output from the remote application.
Stdout	This property provides the standard output (stdout) from the remote application.
Timeout	A timeout for the class.

Method List

The following is the full list of the methods of the class with short descriptions. Click on the links for further details.


Config	Sets or retrieves a configuration setting.
Connect	This method connects to the remote host without performing any action.
Disconnect	This method disconnects from the RemoteHost .
DoEvents	Processes events from the internal message queue.
Execute	This method executes a Command on the remote host.
Interrupt	Interrupt the current method.
Reset	This method resets the class.
Send	This method sends a standard input to the program executing on the remote host.
SendCommand	This method sends the specified command to the server.
SendStdinBytes	This method sends binary data to the remote host.
SendStdinText	This method sends text to the remote host.

Event List

The following is the full list of the events fired by the class with short descriptions. Click on the links for further details.


Connected	This event is fired immediately after a connection completes (or fails).
ConnectionStatus	This event is fired to indicate changes in the connection state.
Disconnected	This event is fired when a connection is closed.
Error	Fired when information is available about errors during data delivery.
Stderr	This event is fired when data (complete lines) come in through stderr.
Stdout	This event is fired when data (complete lines) come in through stdout.

Config Settings

The following is a list of config settings for the class with short descriptions. Click on the links for further details.


EnableStderr	Enables or disables secondary (stderr) stream.
MaxStderr	Maximum storage available for the stderr buffer.
MaxStdout	Maximum storage available for the stdout buffer.
StderrPort	The local port from which the remote system sends the stderr stream.
ConnectionTimeout	Sets a separate timeout value for establishing a connection.
FirewallAutoDetect	Tells the class whether or not to automatically detect and use firewall system settings, if available.
FirewallHost	Name or IP address of firewall (optional).
FirewallPassword	Password to be used if authentication is to be used when connecting through the firewall.
FirewallPort	The TCP port for the FirewallHost;.
FirewallType	Determines the type of firewall to connect through.
FirewallUser	A user name if authentication is to be used connecting through a firewall.
KeepAliveInterval	The retry interval, in milliseconds, to be used when a TCP keep-alive packet is sent and no response is received.
KeepAliveTime	The inactivity time in milliseconds before a TCP keep-alive packet is sent.
Linger	When set to True, connections are terminated gracefully.
LingerTime	Time in seconds to have the connection linger.
LocalHost	The name of the local host through which connections are initiated or accepted.
LocalPort	The port in the local host where the class binds.
MaxLineLength	The maximum amount of data to accumulate when no EOL is found.
MaxTransferRate	The transfer rate limit in bytes per second.
ProxyExceptionsList	A semicolon separated list of hosts and IPs to bypass when using a proxy.
TCPKeepAlive	Determines whether or not the keep alive socket option is enabled.
TcpNoDelay	Whether or not to delay when sending packets.
UseIPv6	Whether to use IPv6.
LogSSLPackets	Controls whether SSL packets are logged when using the internal security API.
OpenSSLCADir	The path to a directory containing CA certificates.
OpenSSLCAFile	Name of the file containing the list of CA's trusted by your application.
OpenSSLCipherList	A string that controls the ciphers to be used by SSL.
OpenSSLPrngSeedData	The data to seed the pseudo random number generator (PRNG).
ReuseSSLSession	Determines if the SSL session is reused.
SSLAcceptAnyServerCert	Whether to trust any certificate presented by the server.
SSLCACerts	A newline separated list of CA certificate to use during SSL client authentication.
SSLCipherStrength	The minimum cipher strength used for bulk encryption.
SSLEnabledCipherSuites	The cipher suite to be used in an SSL negotiation.
SSLEnabledProtocols	Used to enable/disable the supported security protocols.
SSLEnableRenegotiation	Whether the renegotiation_info SSL extension is supported.
SSLIncludeCertChain	Whether the entire certificate chain is included in the SSLServerAuthentication event.
SSLKeyLogFile	The location of a file where per-session secrets are written for debugging purposes.
SSLNegotiatedCipher	Returns the negotiated cipher suite.
SSLNegotiatedCipherStrength	Returns the negotiated cipher suite strength.
SSLNegotiatedCipherSuite	Returns the negotiated cipher suite.
SSLNegotiatedKeyExchange	Returns the negotiated key exchange algorithm.
SSLNegotiatedKeyExchangeStrength	Returns the negotiated key exchange algorithm strength.
SSLNegotiatedVersion	Returns the negotiated protocol version.
SSLSecurityFlags	Flags that control certificate verification.
SSLServerCACerts	A newline separated list of CA certificate to use during SSL server certificate validation.
TLS12SignatureAlgorithms	Defines the allowed TLS 1.2 signature algorithms when SSLProvider is set to Internal.
TLS12SupportedGroups	The supported groups for ECC.
TLS13KeyShareGroups	The groups for which to pregenerate key shares.
TLS13SignatureAlgorithms	The allowed certificate signature algorithms.
TLS13SupportedGroups	The supported groups for (EC)DHE key exchange.
AbsoluteTimeout	Determines whether timeouts are inactivity timeouts or absolute timeouts.
FirewallData	Used to send extra data to the firewall.
InBufferSize	The size in bytes of the incoming queue of the socket.
OutBufferSize	The size in bytes of the outgoing queue of the socket.
BuildInfo	Information about the product's build.
CodePage	The system code page used for Unicode to Multibyte translations.
LicenseInfo	Information about the current license.
MaskSensitive	Whether sensitive data is masked in log messages.
UseInternalSecurityAPI	Whether or not to use the system security libraries or an internal implementation.

Rshell.BytesSent Property

This property includes the number of bytes actually sent after an assignment to Stdin.

Syntax

getBytesSent(): number;

Default Value

Remarks

The BytesSent property shows how many bytes were sent after the last assignment to Stdin. Please check the Stdin property for more information.

This property is read-only and not available at design time.

Rshell.Connected Property

This shows whether the class is connected.

Syntax

isConnected(): boolean;

Default Value

FALSE

Remarks

This property is used to determine whether or not the class is connected to the remote host.

Note: It is recommended to use the Connect or Disconnect method instead of setting this property.

This property is not available at design time.

Rshell.EOF Property

If this property is True, the connection has closed, and no buffered data are available.

Syntax

isEOF(): boolean;

Default Value

TRUE

Remarks

This property is read-only.

Rshell.EOL Property

This property is used to break the stdout data stream into chunks separated by its value.

Syntax

getEOL(): Uint8Array;
setEOL(EOL: Uint8Array): void;

Default Value

"ASCII code 10 (newline)"

Remarks

The EOL property is used to define boundaries in the Stdout stream using the value of the property.

This property is not available at design time.

Rshell.ErrEOL Property

This property is used to break the stderr data stream into chunks separated by its value.

Syntax

getErrEOL(): Uint8Array;
setErrEOL(errEOL: Uint8Array): void;

Default Value

"ASCII code 10 (newline)"

Remarks

The ErrEOL property is used to define boundaries in the Stderr stream using the value of the property.

This property is not available at design time.

Rshell.ErrorMessage Property

This property includes the error message that is returned when any of the steps before command execution fail.

Syntax

getErrorMessage(): string;

Default Value

Remarks

This error message is returned on a separate connection associated with error messages.

This property is read-only.

Rshell.Firewall Property

A set of properties related to firewall access.

Syntax

getFirewall(): Firewall;
setFirewall(firewall: Firewall): void;

Default Value

Remarks

This is a Firewall-type property, which contains fields describing the firewall through which the class will attempt to connect.

Please refer to the Firewall type for a complete list of fields.

Rshell.LocalHost Property

The name of the local host or user-assigned IP interface through which connections are initiated or accepted.

Syntax

getLocalHost(): string;
setLocalHost(localHost: string): void;

Default Value

Remarks

The LocalHost property contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multi-homed hosts (machines with more than one IP interface) setting LocalHost to the value of an interface will make the class initiate connections (or accept in the case of server classs) only through that interface.

If the class is connected, the LocalHost property shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multi-homed hosts (machines with more than one IP interface).

NOTE: LocalHost is not persistent. You must always set it in code, and never in the property window.

Rshell.LocalPort Property

This property includes the Transmission Control Protocol (TCP) port in the local host where the class binds.

Syntax

getLocalPort(): number;
setLocalPort(localPort: number): void;

Default Value

Remarks

The LocalPort property must be set before a connection is attempted. This property instructs the class to bind to a specific port (or communication endpoint) in the local machine.

Setting it to zero (the default) enables the class to choose a port at random. The chosen port will be shown by the LocalPort property after the connection is established.

LocalPort cannot be changed once a connection is made. Any attempt to set the LocalPort property when a connection is active will generate an error.

Note: Use this property with caution. If you supply a value, it must be an available port on the system, or an error will be returned. Furthermore, the class always attempts to bind to a secure (sub 1000) port when the value of LocalPort is the default (zero). If you supply your own value, ensure that the remote system is configured to allow that particular value.

This property is not available at design time.

Rshell.LocalUser Property

This property includes the identifier of the user on the local machine.

Syntax

getLocalUser(): string;
setLocalUser(localUser: string): void;

Default Value

Remarks

This property contains the identifier of the user on the local machine. This must be the identifier of a user in the local host for whom remote execution of commands is permitted in the remote host.

Rshell.RemoteHost Property

This property includes the address of the remote host. Domain names are resolved to IP addresses.

Syntax

getRemoteHost(): string;
setRemoteHost(remoteHost: string): void;

Default Value

Remarks

This property specifies the IP address (IP number in dotted internet format) or the domain name of the remote host. It is set before a connection is attempted and cannot be changed once a connection is established.

If this property is set to a domain name, a DNS request is initiated, and upon successful termination of the request, this property is set to the corresponding address. If the search is not successful, an error is returned.

If the class is configured to use a SOCKS firewall, the value assigned to this property may be preceded with an "*". If this is the case, the host name is passed to the firewall unresolved and the firewall performs the DNS resolution.

Example. Connecting:

TCPClientControl.RemoteHost = "MyHostNameOrIP" TCPClientControl.RemotePort = 777 TCPClientControl.Connected = true

Rshell.RemotePort Property

This property includes the remote shell service port (default is 514).

Syntax

getRemotePort(): number;
setRemotePort(remotePort: number): void;

Default Value

514

Remarks

This property specifies the rshell service port on the remote host.

A valid port number (a value between 1 and 65535) is required for the connection to take place. This property must be set before command execution is attempted.

This property is not available at design time.

Rshell.RemoteUser Property

This property includes the Id of the user on the remote host.

Syntax

getRemoteUser(): string;
setRemoteUser(remoteUser: string): void;

Default Value

Remarks

This must be the Id of a user in the remote host for whom remote execution of commands is permitted.

Rshell.Stderr Property

This property returns the standard error (stderr) output from the remote application.

Syntax

getStderr(): Uint8Array;

Default Value

Remarks

This property is set to an empty string before each new request.

This property is read-only and not available at design time.

Rshell.Stdout Property

This property provides the standard output (stdout) from the remote application.

Syntax

getStdout(): Uint8Array;

Default Value

Remarks

The property is set to an empty string before each new request.

This property is read-only and not available at design time.

Rshell.Timeout Property

A timeout for the class.

Syntax

getTimeout(): number;
setTimeout(timeout: number): void;

Default Value

Remarks

If the Timeout property is set to 0, all operations return immediately, potentially failing with a WOULDBLOCK error if data cannot be sent immediately.

If Timeout is set to a positive value, data is sent in a blocking manner and the class will wait for the operation to complete before returning control. The class will handle any potential WOULDBLOCK errors internally and automatically retry the operation for a maximum of Timeout seconds.

The class will use DoEvents to enter an efficient wait loop during any potential waiting period, making sure that all system events are processed immediately as they arrive. This ensures that the host application does not "freeze" and remains responsive.

If Timeout expires, and the operation is not yet complete, the class .

Please note that by default, all timeouts are inactivity timeouts, i.e. the timeout period is extended by Timeout seconds when any amount of data is successfully sent or received.

The default value for the Timeout property is 60 seconds.

Rshell.config Method

Sets or retrieves a configuration setting.

Syntax

async rshell.config(configurationString : string): Promise<string>

Remarks

Config is a generic method available in every class. It is used to set and retrieve configuration settings for the class.

These settings are similar in functionality to properties, but they are rarely used. In order to avoid "polluting" the property namespace of the class, access to these internal properties is provided through the Config method.

To set a configuration setting named PROPERTY, you must call Config("PROPERTY=VALUE"), where VALUE is the value of the setting expressed as a string. For boolean values, use the strings "True", "False", "0", "1", "Yes", or "No" (case does not matter).

To read (query) the value of a configuration setting, you must call Config("PROPERTY"). The value will be returned as a string.

Rshell.connect Method

This method connects to the remote host without performing any action.

Syntax

async rshell.connect(): Promise<void>

Remarks

This method establishes a connection with the remote host specified by URL, but it does not send a request. In most cases, it is recommended to use the appropriate method, such as Get or Post, which will both establish a connection and send a request.

This method may be useful in cases in which it is desirable to establish a connection without performing any operation (e.g., when testing connectivity).

Rshell.disconnect Method

This method disconnects from the RemoteHost .

Syntax

async rshell.disconnect(): Promise<void>

Remarks

This method disconnects from the RemoteHost. Calling this method is normally unnecessary, unless you wish to interrupt the remote program, or the remote program is waiting for standard input to end before terminating.

Rshell.doEvents Method

Processes events from the internal message queue.

Syntax

async rshell.doEvents(): Promise<void>

Remarks

When DoEvents is called, the class processes any available events. If no events are available, it waits for a preset period of time, and then returns.

Rshell.execute Method

This method executes a Command on the remote host.

Syntax

async rshell.execute(command : string): Promise<void>

Remarks

This method executes a Command on the remote host. Calling this method is equivalent to setting the Command property to Command.

Example. Execute a Command:

RshellControl.Execute("cd /home/username/; ls -al; cd/; ls")

Rshell.interrupt Method

Interrupt the current method.

Syntax

async rshell.interrupt(): Promise<void>

Remarks

If there is no method in progress, Interrupt simply returns, doing nothing.

Rshell.reset Method

This method resets the class.

Syntax

async rshell.reset(): Promise<void>

Remarks

This method will reset the class's properties to their default values.

Rshell.send Method

This method sends a standard input to the program executing on the remote host.

Syntax

async rshell.send(text : Uint8Array): Promise<void>

Remarks

This method sends a standard input to the program executing on the remote host. Calling this method is equivalent to setting the Stdin property to Text.

Rshell.sendCommand Method

This method sends the specified command to the server.

Syntax

async rshell.sendCommand(command : string): Promise<void>

Remarks

This method sends the Command to the RemoteHost. There is no need to append an end-of-line character to the command.

Rshell.sendStdinBytes Method

This method sends binary data to the remote host.

Syntax

async rshell.sendStdinBytes(data : Uint8Array): Promise<void>

Remarks

This method sends the specified binary data to the remote host. The data provided are used as input for the process on the remote host. To send text, use the SendStdinText method instead.

If you are sending data to the remote host faster than it can process it, or faster than the network bandwidth allows, the outgoing queue might fill up. When this happens the class .

Rshell.sendStdinText Method

This method sends text to the remote host.

Syntax

async rshell.sendStdinText(text : string): Promise<void>

Remarks

This method sends the specified text to the remote host. The text provided is used as an input for the process on the remote host. To send binary data, use the SendStdinBytes method instead.

If you are sending data to the remote host faster than it can process it, or faster than the network bandwidth allows, the outgoing queue might fill up. When this happens the class .

Rshell.Connected Event

This event is fired immediately after a connection completes (or fails).

Syntax

rshell.on('Connected', listener: (e: {readonly statusCode: number, readonly description: string}) => void )

Remarks

If the connection is made normally, StatusCode is 0 and Description is "OK".

If the connection fails, StatusCode has the error code returned by the Transmission Control Protocol (TCP)/IP stack. Description contains a description of this code. The value of StatusCode is equal to the value of the error.

Please refer to the Error Codes section for more information.

Rshell.ConnectionStatus Event

This event is fired to indicate changes in the connection state.

Syntax

rshell.on('ConnectionStatus', listener: (e: {readonly connectionEvent: string, readonly statusCode: number, readonly description: string}) => void )

Remarks

The ConnectionStatus event is fired when the connection state changes: for example, completion of a firewall or proxy connection or completion of a security handshake.

The ConnectionEvent parameter indicates the type of connection event. Values may include the following:


	Firewall connection complete.
	Secure Sockets Layer (SSL) or S/Shell handshake complete (where applicable).
	Remote host connection complete.
	Remote host disconnected.
	SSL or S/Shell connection broken.
	Firewall host disconnected.

StatusCode has the error code returned by the Transmission Control Protocol (TCP)/IP stack. Description contains a description of this code. The value of StatusCode is equal to the value of the error.

Rshell.Disconnected Event

This event is fired when a connection is closed.

Syntax

rshell.on('Disconnected', listener: (e: {readonly statusCode: number, readonly description: string}) => void )

Remarks

If the connection is broken normally, StatusCode is 0 and Description is "OK".

If the connection is broken for any other reason, StatusCode has the error code returned by the Transmission Control Protocol (TCP/IP) subsystem. Description contains a description of this code. The value of StatusCode is equal to the value of the TCP/IP error.

Please refer to the Error Codes section for more information.

Rshell.Error Event

Fired when information is available about errors during data delivery.

Syntax

rshell.on('Error', listener: (e: {readonly errorCode: number, readonly description: string}) => void )

Remarks

The Error event is fired in case of exceptional conditions during message processing. Normally the class .

The ErrorCode parameter contains an error code, and the Description parameter contains a textual description of the error. For a list of valid error codes and their descriptions, please refer to the Error Codes section.

Rshell.Stderr Event

This event is fired when data (complete lines) come in through stderr.

Syntax

rshell.on('Stderr', listener: (e: {readonly text: string, readonly textB: Uint8Array, readonly EOL: boolean}) => void )

Remarks

The Stderr event is fired every time the process on the remote host outputs a line in its error output. The incoming data are provided through the Text parameter.

EOL indicates whether or not the ErrEOL string was found on the end of Text. If the ErrEOL string was found, then EOL is True; otherwise, it is False.

When the error stream is closed by the server, a string containing only one NULL character is delivered through this event.

Rshell.Stdout Event

This event is fired when data (complete lines) come in through stdout.

Syntax

rshell.on('Stdout', listener: (e: {readonly text: string, readonly textB: Uint8Array, readonly EOL: boolean}) => void )

Remarks

The Stdout event is fired every time the process on the remote host outputs a line in its standard output. The incoming data are provided through the Text parameter.

EOL indicates whether or not the EOL string was found on the end of Text. If the EOL string was found, then EOL is True; otherwise, it is False.

Firewall Type

The firewall the class will connect through.

Remarks

When connecting through a firewall, this type is used to specify different properties of the firewall, such as the firewall and the .

Fields

AutoDetect
boolean
Default Value: False

This property tells the class whether or not to automatically detect and use firewall system settings, if available.

FirewallType
FirewallTypes
Default Value: 0

This property determines the type of firewall to connect through. The applicable values are as follows:


fwNone (0)	No firewall (default setting).
fwTunnel (1)	Connect through a tunneling proxy. is set to 80.
fwSOCKS4 (2)	Connect through a SOCKS4 Proxy. is set to 1080.
fwSOCKS5 (3)	Connect through a SOCKS5 Proxy. is set to 1080.
fwSOCKS4A (10)	Connect through a SOCKS4A Proxy. is set to 1080.

Host
string
Default Value: ""

This property contains the name or IP address of firewall (optional). If a is given, the requested connections will be authenticated through the specified firewall when connecting.

If this property is set to a Domain Name, a DNS request is initiated. Upon successful termination of the request, this property is set to the corresponding address. If the search is not successful, the class .

Password
string
Default Value: ""

This property contains a password if authentication is to be used when connecting through the firewall. If is specified, the and properties are used to connect and authenticate to the given firewall. If the authentication fails, the class .

Port
number
Default Value: 0

This property contains the transmission control protocol (TCP) port for the firewall . See the description of the property for details.

Note: This property is set automatically when is set to a valid value. See the description of the property for details.

User
string
Default Value: ""

This property contains a user name if authentication is to be used connecting through a firewall. If the is specified, this property and properties are used to connect and authenticate to the given Firewall. If the authentication fails, the class .

Constructors

public Firewall();

Config Settings (class ipworks.rshell)

The class accepts one or more of the following configuration settings. Configuration settings are similar in functionality to properties, but they are rarely used. In order to avoid "polluting" the property namespace of the class, access to these internal properties is provided through the Config method.

Rexec/Rshell Config Settings

EnableStderr: Enables or disables secondary (stderr) stream.

Some systems (most notably certain versions of Linux) do not support the secondary stderr stream of rexec/rshell. For these systems, you must turn stderr off. Any stderr output will then be provided through stdout.

The default value for this configuration setting is True.

MaxStderr: Maximum storage available for the stderr buffer.

This configuration setting indicates the maximum amount of characters that the class will store in the Stderr property. The default value is -1, which indicates there is no maximum. A value of zero (0) will disable accumulation of stderr in the Stderr property, although the Stderr event will still continue to fire.

MaxStdout: Maximum storage available for the stdout buffer.

This configuration setting indicates the maximum amount of characters that the class will store in the Stdout property. The default value is -1, which indicates there is no maximum. A value of zero (0) will disable accumulation of stdout in the Stdout property, although the Stdout event will still continue to fire.

StderrPort: The local port from which the remote system sends the stderr stream.

The default value is zero, which instructs the class to use a random port. Use this property with caution. If you supply a value, it must be an available port on the system or an error will be returned.

Some systems do not support secondary stderr streams. Please refer to the EnableStderr configuration setting for more information.

TCPClient Config Settings

ConnectionTimeout: Sets a separate timeout value for establishing a connection.

When set, this configuration setting allows you to specify a different timeout value for establishing a connection. Otherwise, the class will use Timeout for establishing a connection and transmitting/receiving data.

FirewallAutoDetect: Tells the class whether or not to automatically detect and use firewall system settings, if available.

This configuration setting is provided for use by classs that do not directly expose Firewall properties.

FirewallHost: Name or IP address of firewall (optional).

If a FirewallHost is given, requested connections will be authenticated through the specified firewall when connecting.

If the FirewallHost setting is set to a Domain Name, a DNS request is initiated. Upon successful termination of the request, the FirewallHost setting is set to the corresponding address. If the search is not successful, an error is returned.

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

FirewallPassword: Password to be used if authentication is to be used when connecting through the firewall.

If FirewallHost is specified, the FirewallUser and FirewallPassword settings are used to connect and authenticate to the given firewall. If the authentication fails, the class .

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

FirewallPort: The TCP port for the FirewallHost;.

The FirewallPort is set automatically when FirewallType is set to a valid value.

Note: This configuration setting is provided for use by classs that do not directly expose Firewall properties.

FirewallType: Determines the type of firewall to connect through.

The appropriate values are as follows:


0	No firewall (default setting).
1	Connect through a tunneling proxy. FirewallPort is set to 80.
2	Connect through a SOCKS4 Proxy. FirewallPort is set to 1080.
3	Connect through a SOCKS5 Proxy. FirewallPort is set to 1080.
10	Connect through a SOCKS4A Proxy. FirewallPort is set to 1080.

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

FirewallUser: A user name if authentication is to be used connecting through a firewall.

If the FirewallHost is specified, the FirewallUser and FirewallPassword settings are used to connect and authenticate to the Firewall. If the authentication fails, the class .

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

KeepAliveInterval: The retry interval, in milliseconds, to be used when a TCP keep-alive packet is sent and no response is received.

When set, TCPKeepAlive will automatically be set to True. A TCP keep-alive packet will be sent after a period of inactivity as defined by KeepAliveTime. If no acknowledgment is received from the remote host, the keep-alive packet will be sent again. This configuration setting specifies the interval at which the successive keep-alive packets are sent in milliseconds. This system default if this value is not specified here is 1 second.

Note: This value is not applicable in macOS.

KeepAliveTime: The inactivity time in milliseconds before a TCP keep-alive packet is sent.

When set, TCPKeepAlive will automatically be set to True. By default, the operating system will determine the time a connection is idle before a Transmission Control Protocol (TCP) keep-alive packet is sent. This system default if this value is not specified here is 2 hours. In many cases, a shorter interval is more useful. Set this value to the desired interval in milliseconds.

Linger: When set to True, connections are terminated gracefully.

This property controls how a connection is closed. The default is True.

In the case that Linger is True (default), two scenarios determine how long the connection will linger. In the first, if LingerTime is 0 (default), the system will attempt to send pending data for a connection until the default IP timeout expires.

In the second scenario, if LingerTime is a positive value, the system will attempt to send pending data until the specified LingerTime is reached. If this attempt fails, then the system will reset the connection.

The default behavior (which is also the default mode for stream sockets) might result in a long delay in closing the connection. Although the class returns control immediately, the system could hold system resources until all pending data are sent (even after your application closes).

Setting this property to False forces an immediate disconnection. If you know that the other side has received all the data you sent (e.g., by a client acknowledgment), setting this property to False might be the appropriate course of action.

LingerTime: Time in seconds to have the connection linger.

LingerTime is the time, in seconds, the socket connection will linger. This value is 0 by default, which means it will use the default IP timeout.

LocalHost: The name of the local host through which connections are initiated or accepted.

The LocalHost setting contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

If the class is connected, the LocalHost setting shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multi-homed hosts (machines with more than one IP interface).

LocalPort: The port in the local host where the class binds.

This must be set before a connection is attempted. It instructs the class to bind to a specific port (or communication endpoint) in the local machine.

Setting this to 0 (default) enables the system to choose a port at random. The chosen port will be shown by LocalPort after the connection is established.

LocalPort cannot be changed once a connection is made. Any attempt to set this when a connection is active will generate an error.

This; setting is useful when trying to connect to services that require a trusted port in the client side. An example is the remote shell (rsh) service in UNIX systems.

MaxLineLength: The maximum amount of data to accumulate when no EOL is found.

MaxLineLength is the size of an internal buffer, which holds received data while waiting for an EOL string.

If an EOL string is found in the input stream before MaxLineLength bytes are received, the DataIn event is fired with the EOL parameter set to True, and the buffer is reset.

If no EOL is found, and MaxLineLength bytes are accumulated in the buffer, the DataIn event is fired with the EOL parameter set to False, and the buffer is reset.

The minimum value for MaxLineLength is 256 bytes. The default value is 2048 bytes.

MaxTransferRate: The transfer rate limit in bytes per second.

This configuration setting can be used to throttle outbound TCP traffic. Set this to the number of bytes to be sent per second. By default, this is not set and there is no limit.

ProxyExceptionsList: A semicolon separated list of hosts and IPs to bypass when using a proxy.

This configuration setting optionally specifies a semicolon-separated list of hostnames or IP addresses to bypass when a proxy is in use. When requests are made to hosts specified in this property, the proxy will not be used. For instance:

www.google.com;www.nsoftware.com

TCPKeepAlive: Determines whether or not the keep alive socket option is enabled.

If set to True, the socket's keep-alive option is enabled and keep-alive packets will be sent periodically to maintain the connection. Set KeepAliveTime and KeepAliveInterval to configure the timing of the keep-alive packets.

Note: This value is not applicable in Java.

TcpNoDelay: Whether or not to delay when sending packets.

When true, the socket will send all data that is ready to send at once. When false, the socket will send smaller buffered packets of data at small intervals. This is known as the Nagle algorithm.

By default, this config is set to false.

UseIPv6: Whether to use IPv6.

When set to 0 (default), the class will use IPv4 exclusively. When set to 1, the class will use IPv6 exclusively. To instruct the class to prefer IPv6 addresses, but use IPv4 if IPv6 is not supported on the system, this setting should be set to 2. The default value is 0. Possible values are:


0	IPv4 Only
1	IPv6 Only
2	IPv6 with IPv4 fallback

SSL Config Settings

LogSSLPackets: Controls whether SSL packets are logged when using the internal security API.

When SSLProvider is set to Internal, this setting controls whether SSL packets should be logged. By default, this setting is False, as it is only useful for debugging purposes.

When enabled, SSL packet logs are output using the SSLStatus event, which will fire each time an SSL packet is sent or received.

Enabling this setting has no effect if SSLProvider is set to Platform.

OpenSSLCADir: The path to a directory containing CA certificates.

This functionality is available only when the provider is OpenSSL.

The path set by this property should point to a directory containing CA certificates in PEM format. The files each contain one CA certificate. The files are looked up by the CA subject name hash value, which must hence be available. If more than one CA certificate with the same name hash value exist, the extension must be different (e.g. 9d66eef0.0, 9d66eef0.1 etc). OpenSSL recommends to use the c_rehash utility to create the necessary links. Please refer to the OpenSSL man page SSL_CTX_load_verify_locations(3) for details.

OpenSSLCAFile: Name of the file containing the list of CA's trusted by your application.

This functionality is available only when the provider is OpenSSL.

The file set by this property should contain a list of CA certificates in PEM format. The file can contain several CA certificates identified by

-----BEGIN CERTIFICATE-----

... (CA certificate in base64 encoding) ...

-----END CERTIFICATE-----

sequences. Before, between, and after the certificates text is allowed which can be used e.g. for descriptions of the certificates. Please refer to the OpenSSL man page SSL_CTX_load_verify_locations(3) for details.

OpenSSLCipherList: A string that controls the ciphers to be used by SSL.

This functionality is available only when the provider is OpenSSL.

The format of this string is described in the OpenSSL man page ciphers(1) section "CIPHER LIST FORMAT". Please refer to it for details. The default string "DEFAULT" is determined at compile time and is normally equivalent to "ALL:!ADH:RC4+RSA:+SSLv2:@STRENGTH".

OpenSSLPrngSeedData: The data to seed the pseudo random number generator (PRNG).

This functionality is available only when the provider is OpenSSL.

By default OpenSSL uses the device file "/dev/urandom" to seed the PRNG and setting OpenSSLPrngSeedData is not required. If set, the string specified is used to seed the PRNG.

ReuseSSLSession: Determines if the SSL session is reused.

If set to true, the class will reuse the context if and only if the following criteria are met:

The target host name is the same.
The system cache entry has not expired (default timeout is 10 hours).
The application process that calls the function is the same.
The logon session is the same.
The instance of the class is the same.

SSLAcceptAnyServerCert: Whether to trust any certificate presented by the server.

This setting disables all certificate verification when set to True. This configuration setting must be enabled to trust a self-signed certificate. It is not recommended to enable this configuration setting in a production environment. The default value is False.

SSLCACerts: A newline separated list of CA certificate to use during SSL client authentication.

This setting specifies one or more CA certificates to be included in the request when performing SSL client authentication. Some servers require the entire chain, including CA certificates, to be presented when performing SSL client authentication. The value of this setting is a newline (CrLf) separated list of certificates. For instance:

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
..
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

SSLCipherStrength: The minimum cipher strength used for bulk encryption.

This minimum cipher strength largely dependent on the security modules installed on the system. If the cipher strength specified is not supported, an error will be returned when connections are initiated.

Please note that this setting contains the minimum cipher strength requested from the security library. The actual cipher strength used for the connection is shown by the SSLStatus event.

Use this setting with caution. Requesting a lower cipher strength than necessary could potentially cause serious security vulnerabilities in your application.

When the provider is OpenSSL, SSLCipherStrength is currently not supported. This functionality is instead made available through the OpenSSLCipherList config setting.

SSLEnabledCipherSuites: The cipher suite to be used in an SSL negotiation.

The enabled cipher suites to be used in SSL negotiation.

By default, the enabled cipher suites will include all available ciphers ("*").

The special value "*" means that the class will pick all of the supported cipher suites. If SSLEnabledCipherSuites is set to any other value, only the specified cipher suites will be considered.

Multiple cipher suites are separated by semicolons.

Example values when SSLProvider is set to Platform: obj.config("SSLEnabledCipherSuites=*"); obj.config("SSLEnabledCipherSuites=CALG_AES_256"); obj.config("SSLEnabledCipherSuites=CALG_AES_256;CALG_3DES"); Possible values when SSLProvider is set to Platform include:

CALG_3DES
CALG_3DES_112
CALG_AES
CALG_AES_128
CALG_AES_192
CALG_AES_256
CALG_AGREEDKEY_ANY
CALG_CYLINK_MEK
CALG_DES
CALG_DESX
CALG_DH_EPHEM
CALG_DH_SF
CALG_DSS_SIGN
CALG_ECDH
CALG_ECDH_EPHEM
CALG_ECDSA
CALG_ECMQV
CALG_HASH_REPLACE_OWF
CALG_HUGHES_MD5
CALG_HMAC
CALG_KEA_KEYX
CALG_MAC
CALG_MD2
CALG_MD4
CALG_MD5
CALG_NO_SIGN
CALG_OID_INFO_CNG_ONLY
CALG_OID_INFO_PARAMETERS
CALG_PCT1_MASTER
CALG_RC2
CALG_RC4
CALG_RC5
CALG_RSA_KEYX
CALG_RSA_SIGN
CALG_SCHANNEL_ENC_KEY
CALG_SCHANNEL_MAC_KEY
CALG_SCHANNEL_MASTER_HASH
CALG_SEAL
CALG_SHA
CALG_SHA1
CALG_SHA_256
CALG_SHA_384
CALG_SHA_512
CALG_SKIPJACK
CALG_SSL2_MASTER
CALG_SSL3_MASTER
CALG_SSL3_SHAMD5
CALG_TEK
CALG_TLS1_MASTER
CALG_TLS1PRF

Example values when SSLProvider is set to Internal:

obj.config("SSLEnabledCipherSuites=*");
obj.config("SSLEnabledCipherSuites=TLS_DHE_DSS_WITH_AES_128_CBC_SHA");
obj.config("SSLEnabledCipherSuites=TLS_DHE_DSS_WITH_AES_128_CBC_SHA;TLS_DH_ANON_WITH_AES_128_CBC_SHA");

Possible values when SSLProvider is set to Internal include:

TLS_ECDHE_ECDSA_WITH_AES_256_GCM_SHA384
TLS_ECDHE_ECDSA_WITH_AES_128_GCM_SHA256
TLS_ECDHE_RSA_WITH_AES_128_GCM_SHA256
TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384
TLS_ECDH_ECDSA_WITH_AES_256_GCM_SHA384
TLS_RSA_WITH_AES_256_GCM_SHA384
TLS_RSA_WITH_AES_128_GCM_SHA256
TLS_ECDH_ECDSA_WITH_AES_128_GCM_SHA256
TLS_DHE_DSS_WITH_AES_256_GCM_SHA384
TLS_DHE_RSA_WITH_AES_256_GCM_SHA384
TLS_ECDH_RSA_WITH_AES_256_GCM_SHA384
TLS_ECDH_RSA_WITH_AES_128_GCM_SHA256
TLS_DHE_RSA_WITH_AES_128_GCM_SHA256
TLS_DHE_DSS_WITH_AES_128_GCM_SHA256
TLS_DH_RSA_WITH_AES_128_GCM_SHA256 (Not Recommended)
TLS_DH_RSA_WITH_AES_256_GCM_SHA384 (Not Recommended)
TLS_DH_DSS_WITH_AES_128_GCM_SHA256 (Not Recommended)
TLS_DH_DSS_WITH_AES_256_GCM_SHA384 (Not Recommended)
TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA384
TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA256
TLS_ECDH_ECDSA_WITH_AES_256_CBC_SHA384
TLS_DHE_DSS_WITH_AES_256_CBC_SHA256
TLS_RSA_WITH_AES_256_CBC_SHA256
TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA384
TLS_ECDH_RSA_WITH_AES_256_CBC_SHA384
TLS_DHE_RSA_WITH_AES_256_CBC_SHA256
TLS_DHE_RSA_WITH_AES_128_CBC_SHA256
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA256
TLS_RSA_WITH_AES_128_CBC_SHA256
TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA256
TLS_ECDH_RSA_WITH_AES_128_CBC_SHA256
TLS_DHE_DSS_WITH_AES_128_CBC_SHA256
TLS_RSA_WITH_AES_256_CBC_SHA
TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA
TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA
TLS_ECDH_ECDSA_WITH_AES_256_CBC_SHA
TLS_DHE_RSA_WITH_AES_256_CBC_SHA
TLS_ECDH_RSA_WITH_AES_256_CBC_SHA
TLS_DHE_DSS_WITH_AES_256_CBC_SHA
TLS_RSA_WITH_AES_128_CBC_SHA
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA
TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA
TLS_ECDH_RSA_WITH_AES_128_CBC_SHA
TLS_DHE_RSA_WITH_AES_128_CBC_SHA
TLS_DHE_DSS_WITH_AES_128_CBC_SHA
TLS_ECDHE_ECDSA_WITH_3DES_EDE_CBC_SHA
TLS_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA
TLS_ECDH_ECDSA_WITH_3DES_EDE_CBC_SHA
TLS_ECDH_RSA_WITH_3DES_EDE_CBC_SHA
TLS_DHE_RSA_WITH_3DES_EDE_CBC_SHA
TLS_DHE_DSS_WITH_3DES_EDE_CBC_SHA
TLS_RSA_WITH_3DES_EDE_CBC_SHA
TLS_RSA_WITH_DES_CBC_SHA
TLS_DHE_RSA_WITH_DES_CBC_SHA
TLS_DHE_DSS_WITH_DES_CBC_SHA
TLS_RSA_WITH_RC4_128_MD5
TLS_RSA_WITH_RC4_128_SHA

When TLS 1.3 is negotiated (see SSLEnabledProtocols) only the following cipher suites are supported:

TLS_AES_256_GCM_SHA384
TLS_CHACHA20_POLY1305_SHA256
TLS_AES_128_GCM_SHA256

SSLEnabledCipherSuites is used together with SSLCipherStrength.

SSLEnabledProtocols: Used to enable/disable the supported security protocols.

Used to enable/disable the supported security protocols.

Not all supported protocols are enabled by default (the value of this setting is 4032). If you want more granular control over the enabled protocols, you can set this property to the binary 'OR' of one or more of the following values:


TLS1.3	12288 (Hex 3000)
TLS1.2	3072 (Hex C00) (Default)
TLS1.1	768 (Hex 300) (Default)
TLS1	192 (Hex C0) (Default)
SSL3	48 (Hex 30) [Platform Only]
SSL2	12 (Hex 0C) [Platform Only]

SSLEnabledProtocols - TLS 1.3 Notes

In the JavaScript edition the platform implementation is used when TLS 1.3 is enabled and SSLEnabledCipherSuites and other similar SSL configuration settings are not supported.

SSLEnabledProtocols: SSL2 and SSL3 Notes:

SSL 2.0 and 3.0 are not supported by the class when the SSLProvider is set to internal. To use SSL 2.0 or SSL 3.0, the platform security API must have the protocols enabled and SSLProvider needs to be set to platform.

SSLEnableRenegotiation: Whether the renegotiation_info SSL extension is supported.

This setting specifies whether the renegotiation_info SSL extension will be used in the request when using the internal security API. This setting is true by default, but can be set to false to disable the extension.

This setting is only applicable when SSLProvider is set to Internal.

SSLIncludeCertChain: Whether the entire certificate chain is included in the SSLServerAuthentication event.

This setting specifies whether the Encoded parameter of the SSLServerAuthentication event contains the full certificate chain. By default this value is False and only the leaf certificate will be present in the Encoded parameter of the SSLServerAuthentication event.

If set to True all certificates returned by the server will be present in the Encoded parameter of the SSLServerAuthentication event. This includes the leaf certificate, any intermediate certificate, and the root certificate.

SSLKeyLogFile: The location of a file where per-session secrets are written for debugging purposes.

This setting optionally specifies the full path to a file on disk where per-session secrets are stored for debugging purposes.

When set, the class will save the session secrets in the same format as the SSLKEYLOGFILE environment variable functionality used by most major browsers and tools such as Chrome, Firefox, and cURL. This file can then be used in tools such as Wireshark to decrypt TLS traffice for debugging purposes. When writing to this file the class will only append, it will not overwrite previous values.

Note: This setting is only applicable when SSLProvider is set to Internal.

SSLNegotiatedCipher: Returns the negotiated cipher suite.

Returns the cipher suite negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipher[connId]");

SSLNegotiatedCipherStrength: Returns the negotiated cipher suite strength.

Returns the strength of the cipher suite negotiated during the SSL handshake.

Note: For server components (e.g.TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipherStrength[connId]");

SSLNegotiatedCipherSuite: Returns the negotiated cipher suite.

Returns the cipher suite negotiated during the SSL handshake represented as a single string.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipherSuite[connId]");

SSLNegotiatedKeyExchange: Returns the negotiated key exchange algorithm.

Returns the key exchange algorithm negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedKeyExchange[connId]");

SSLNegotiatedKeyExchangeStrength: Returns the negotiated key exchange algorithm strength.

Returns the strenghth of the key exchange algorithm negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedKeyExchangeStrength[connId]");

SSLNegotiatedVersion: Returns the negotiated protocol version.

Returns the protocol version negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedVersion[connId]");

SSLSecurityFlags: Flags that control certificate verification.

The following flags are defined (specified in hexadecimal notation). They can be or-ed together to exclude multiple conditions:


0x00000001	Ignore time validity status of certificate.
0x00000002	Ignore time validity status of CTL.
0x00000004	Ignore non-nested certificate times.
0x00000010	Allow unknown Certificate Authority.
0x00000020	Ignore wrong certificate usage.
0x00000100	Ignore unknown certificate revocation status.
0x00000200	Ignore unknown CTL signer revocation status.
0x00000400	Ignore unknown Certificate Authority revocation status.
0x00000800	Ignore unknown Root revocation status.
0x00008000	Allow test Root certificate.
0x00004000	Trust test Root certificate.
0x80000000	Ignore non-matching CN (certificate CN not-matching server name).

This functionality is currently not available when the provider is OpenSSL.

SSLServerCACerts: A newline separated list of CA certificate to use during SSL server certificate validation.

This setting optionally specifies one or more CA certificates to be used when verifying the server certificate. When verifying the server's certificate the certificates trusted by the system will be used as part of the verification process. If the server's CA certificates are not installed to the trusted system store, they may be specified here so they are included when performing the verification process. This setting should only be set if the server's CA certificates are not already trusted on the system and cannot be installed to the trusted system store.

The value of this setting is a newline (CrLf) separated list of certificates. For instance:

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
..
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

TLS12SignatureAlgorithms: Defines the allowed TLS 1.2 signature algorithms when SSLProvider is set to Internal.

This setting specifies the allowed server certificate signature algorithms when SSLProvider is set to Internal and SSLEnabledProtocols is set to allow TLS 1.2.

When specified the class will verify that the server certificate signature algorithm is among the values specified in this setting. If the server certificate signature algorithm is unsupported the class .

The format of this value is a comma separated list of hash-signature combinations. For instance: component.SSLProvider = TCPClientSSLProviders.sslpInternal; component.Config("SSLEnabledProtocols=3072"); //TLS 1.2 component.Config("TLS12SignatureAlgorithms=sha256-rsa,sha256-dsa,sha1-rsa,sha1-dsa"); The default value for this setting is sha512-ecdsa,sha512-rsa,sha512-dsa,sha384-ecdsa,sha384-rsa,sha384-dsa,sha256-ecdsa,sha256-rsa,sha256-dsa,sha224-ecdsa,sha224-rsa,sha224-dsa,sha1-ecdsa,sha1-rsa,sha1-dsa.

In order to not restrict the server's certificate signature algorithm, specify an empty string as the value for this setting, which will cause the signature_algorithms TLS 1.2 extension to not be sent.

TLS12SupportedGroups: The supported groups for ECC.

This setting specifies a comma separated list of named groups used in TLS 1.2 for ECC.

The default value is ecdhe_secp256r1,ecdhe_secp384r1,ecdhe_secp521r1.

When using TLS 1.2 and SSLProvider is set to Internal, the values refer to the supported groups for ECC. The following values are supported:

"ecdhe_secp256r1" (default)
"ecdhe_secp384r1" (default)
"ecdhe_secp521r1" (default)

TLS13KeyShareGroups: The groups for which to pregenerate key shares.

This setting specifies a comma separated list of named groups used in TLS 1.3 for key exchange. The groups specified here will have key share data pregenerated locally before establishing a connection. This can prevent an additional round trip during the handshake if the group is supported by the server.

The default value is set to balance common supported groups and the computational resources required to generate key shares. As a result only some groups are included by default in this setting.

Note: All supported groups can always be used during the handshake even if not listed here, but if a group is used which is not present in this list it will incur an additional round trip and time to generate the key share for that group.

In most cases this setting does not need to be modified. This should only be modified if there is a specific reason to do so.

The default value is ecdhe_x25519,ecdhe_secp256r1,ecdhe_secp384r1,ffdhe_2048,ffdhe_3072

The values are ordered from most preferred to least preferred. The following values are supported:

"ecdhe_x25519" (default)
"ecdhe_x448"
"ecdhe_secp256r1" (default)
"ecdhe_secp384r1" (default)
"ecdhe_secp521r1"
"ffdhe_2048" (default)
"ffdhe_3072" (default)
"ffdhe_4096"
"ffdhe_6144"
"ffdhe_8192"

TLS13SignatureAlgorithms: The allowed certificate signature algorithms.

This setting holds a comma separated list of allowed signature algorithms. Possible values are:

"ed25519" (default)
"ed448" (default)
"ecdsa_secp256r1_sha256" (default)
"ecdsa_secp384r1_sha384" (default)
"ecdsa_secp521r1_sha512" (default)
"rsa_pkcs1_sha256" (default)
"rsa_pkcs1_sha384" (default)
"rsa_pkcs1_sha512" (default)
"rsa_pss_sha256" (default)
"rsa_pss_sha384" (default)
"rsa_pss_sha512" (default)

The default value is rsa_pss_sha256,rsa_pss_sha384,rsa_pss_sha512,rsa_pkcs1_sha256,rsa_pkcs1_sha384,rsa_pkcs1_sha512,ecdsa_secp256r1_sha256,ecdsa_secp384r1_sha384,ecdsa_secp521r1_sha512,ed25519,ed448. This setting is only applicable when SSLEnabledProtocols includes TLS 1.3.

TLS13SupportedGroups: The supported groups for (EC)DHE key exchange.

This setting specifies a comma separated list of named groups used in TLS 1.3 for key exchange. This setting should only be modified if there is a specific reason to do so.

The default value is ecdhe_x25519,ecdhe_x448,ecdhe_secp256r1,ecdhe_secp384r1,ecdhe_secp521r1,ffdhe_2048,ffdhe_3072,ffdhe_4096,ffdhe_6144,ffdhe_8192

The values are ordered from most preferred to least preferred. The following values are supported:

"ecdhe_x25519" (default)
"ecdhe_x448" (default)
"ecdhe_secp256r1" (default)
"ecdhe_secp384r1" (default)
"ecdhe_secp521r1" (default)
"ffdhe_2048" (default)
"ffdhe_3072" (default)
"ffdhe_4096" (default)
"ffdhe_6144" (default)
"ffdhe_8192" (default)

Socket Config Settings

AbsoluteTimeout: Determines whether timeouts are inactivity timeouts or absolute timeouts.

If AbsoluteTimeout is set to True, any method which does not complete within Timeout seconds will be aborted. By default, AbsoluteTimeout is False, and the timeout is an inactivity timeout.

Note: This option is not valid for UDP ports.

FirewallData: Used to send extra data to the firewall.

When the firewall is a tunneling proxy, use this property to send custom (additional) headers to the firewall (e.g. headers for custom authentication schemes).

InBufferSize: The size in bytes of the incoming queue of the socket.

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be receiving. Increasing the value of the InBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the class is activated the InBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

OutBufferSize: The size in bytes of the outgoing queue of the socket.

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be sending. Increasing the value of the OutBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the class is activated the OutBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

Base Config Settings

BuildInfo: Information about the product's build.

When queried, this setting will return a string containing information about the product's build.

CodePage: The system code page used for Unicode to Multibyte translations.

The default code page is Unicode UTF-8 (65001).

The following is a list of valid code page identifiers:


Identifier	Name
037	IBM EBCDIC - U.S./Canada
437	OEM - United States
500	IBM EBCDIC - International
708	Arabic - ASMO 708
709	Arabic - ASMO 449+, BCON V4
710	Arabic - Transparent Arabic
720	Arabic - Transparent ASMO
737	OEM - Greek (formerly 437G)
775	OEM - Baltic
850	OEM - Multilingual Latin I
852	OEM - Latin II
855	OEM - Cyrillic (primarily Russian)
857	OEM - Turkish
858	OEM - Multilingual Latin I + Euro symbol
860	OEM - Portuguese
861	OEM - Icelandic
862	OEM - Hebrew
863	OEM - Canadian-French
864	OEM - Arabic
865	OEM - Nordic
866	OEM - Russian
869	OEM - Modern Greek
870	IBM EBCDIC - Multilingual/ROECE (Latin-2)
874	ANSI/OEM - Thai (same as 28605, ISO 8859-15)
875	IBM EBCDIC - Modern Greek
932	ANSI/OEM - Japanese, Shift-JIS
936	ANSI/OEM - Simplified Chinese (PRC, Singapore)
949	ANSI/OEM - Korean (Unified Hangul Code)
950	ANSI/OEM - Traditional Chinese (Taiwan; Hong Kong SAR, PRC)
1026	IBM EBCDIC - Turkish (Latin-5)
1047	IBM EBCDIC - Latin 1/Open System
1140	IBM EBCDIC - U.S./Canada (037 + Euro symbol)
1141	IBM EBCDIC - Germany (20273 + Euro symbol)
1142	IBM EBCDIC - Denmark/Norway (20277 + Euro symbol)
1143	IBM EBCDIC - Finland/Sweden (20278 + Euro symbol)
1144	IBM EBCDIC - Italy (20280 + Euro symbol)
1145	IBM EBCDIC - Latin America/Spain (20284 + Euro symbol)
1146	IBM EBCDIC - United Kingdom (20285 + Euro symbol)
1147	IBM EBCDIC - France (20297 + Euro symbol)
1148	IBM EBCDIC - International (500 + Euro symbol)
1149	IBM EBCDIC - Icelandic (20871 + Euro symbol)
1200	Unicode UCS-2 Little-Endian (BMP of ISO 10646)
1201	Unicode UCS-2 Big-Endian
1250	ANSI - Central European
1251	ANSI - Cyrillic
1252	ANSI - Latin I
1253	ANSI - Greek
1254	ANSI - Turkish
1255	ANSI - Hebrew
1256	ANSI - Arabic
1257	ANSI - Baltic
1258	ANSI/OEM - Vietnamese
1361	Korean (Johab)
10000	MAC - Roman
10001	MAC - Japanese
10002	MAC - Traditional Chinese (Big5)
10003	MAC - Korean
10004	MAC - Arabic
10005	MAC - Hebrew
10006	MAC - Greek I
10007	MAC - Cyrillic
10008	MAC - Simplified Chinese (GB 2312)
10010	MAC - Romania
10017	MAC - Ukraine
10021	MAC - Thai
10029	MAC - Latin II
10079	MAC - Icelandic
10081	MAC - Turkish
10082	MAC - Croatia
12000	Unicode UCS-4 Little-Endian
12001	Unicode UCS-4 Big-Endian
20000	CNS - Taiwan
20001	TCA - Taiwan
20002	Eten - Taiwan
20003	IBM5550 - Taiwan
20004	TeleText - Taiwan
20005	Wang - Taiwan
20105	IA5 IRV International Alphabet No. 5 (7-bit)
20106	IA5 German (7-bit)
20107	IA5 Swedish (7-bit)
20108	IA5 Norwegian (7-bit)
20127	US-ASCII (7-bit)
20261	T.61
20269	ISO 6937 Non-Spacing Accent
20273	IBM EBCDIC - Germany
20277	IBM EBCDIC - Denmark/Norway
20278	IBM EBCDIC - Finland/Sweden
20280	IBM EBCDIC - Italy
20284	IBM EBCDIC - Latin America/Spain
20285	IBM EBCDIC - United Kingdom
20290	IBM EBCDIC - Japanese Katakana Extended
20297	IBM EBCDIC - France
20420	IBM EBCDIC - Arabic
20423	IBM EBCDIC - Greek
20424	IBM EBCDIC - Hebrew
20833	IBM EBCDIC - Korean Extended
20838	IBM EBCDIC - Thai
20866	Russian - KOI8-R
20871	IBM EBCDIC - Icelandic
20880	IBM EBCDIC - Cyrillic (Russian)
20905	IBM EBCDIC - Turkish
20924	IBM EBCDIC - Latin-1/Open System (1047 + Euro symbol)
20932	JIS X 0208-1990 & 0121-1990
20936	Simplified Chinese (GB2312)
21025	IBM EBCDIC - Cyrillic (Serbian, Bulgarian)
21027	Extended Alpha Lowercase
21866	Ukrainian (KOI8-U)
28591	ISO 8859-1 Latin I
28592	ISO 8859-2 Central Europe
28593	ISO 8859-3 Latin 3
28594	ISO 8859-4 Baltic
28595	ISO 8859-5 Cyrillic
28596	ISO 8859-6 Arabic
28597	ISO 8859-7 Greek
28598	ISO 8859-8 Hebrew
28599	ISO 8859-9 Latin 5
28605	ISO 8859-15 Latin 9
29001	Europa 3
38598	ISO 8859-8 Hebrew
50220	ISO 2022 Japanese with no halfwidth Katakana
50221	ISO 2022 Japanese with halfwidth Katakana
50222	ISO 2022 Japanese JIS X 0201-1989
50225	ISO 2022 Korean
50227	ISO 2022 Simplified Chinese
50229	ISO 2022 Traditional Chinese
50930	Japanese (Katakana) Extended
50931	US/Canada and Japanese
50933	Korean Extended and Korean
50935	Simplified Chinese Extended and Simplified Chinese
50936	Simplified Chinese
50937	US/Canada and Traditional Chinese
50939	Japanese (Latin) Extended and Japanese
51932	EUC - Japanese
51936	EUC - Simplified Chinese
51949	EUC - Korean
51950	EUC - Traditional Chinese
52936	HZ-GB2312 Simplified Chinese
54936	Windows XP: GB18030 Simplified Chinese (4 Byte)
57002	ISCII Devanagari
57003	ISCII Bengali
57004	ISCII Tamil
57005	ISCII Telugu
57006	ISCII Assamese
57007	ISCII Oriya
57008	ISCII Kannada
57009	ISCII Malayalam
57010	ISCII Gujarati
57011	ISCII Punjabi
65000	Unicode UTF-7
65001	Unicode UTF-8

The following is a list of valid code page identifiers for Mac OS only:


Identifier	Name
1	ASCII
2	NEXTSTEP
3	JapaneseEUC
4	UTF8
5	ISOLatin1
6	Symbol
7	NonLossyASCII
8	ShiftJIS
9	ISOLatin2
10	Unicode
11	WindowsCP1251
12	WindowsCP1252
13	WindowsCP1253
14	WindowsCP1254
15	WindowsCP1250
21	ISO2022JP
30	MacOSRoman
10	UTF16String
0x90000100	UTF16BigEndian
0x94000100	UTF16LittleEndian
0x8c000100	UTF32String
0x98000100	UTF32BigEndian
0x9c000100	UTF32LittleEndian
65536	Proprietary

LicenseInfo: Information about the current license.

When queried, this setting will return a string containing information about the license this instance of a class is using. It will return the following information:

Product: The product the license is for.
Product Key: The key the license was generated from.
License Source: Where the license was found (e.g., RuntimeLicense, License File).
License Type: The type of license installed (e.g., Royalty Free, Single Server).
Last Valid Build: The last valid build number for which the license will work.

MaskSensitive: Whether sensitive data is masked in log messages.

In certain circumstances it may be beneficial to mask sensitive data, like passwords, in log messages. Set this to true to mask sensitive data. The default is true.

This setting only works on these classes: AS3Receiver, AS3Sender, Atom, Client(3DS), FTP, FTPServer, IMAP, OFTPClient, SSHClient, SCP, Server(3DS), Sexec, SFTP, SFTPServer, SSHServer, TCPClient, TCPServer.

UseInternalSecurityAPI: Whether or not to use the system security libraries or an internal implementation.

When set to false, the class will use the system security libraries by default to perform cryptographic functions where applicable.

Setting this configuration setting to true tells the class to use the internal implementation instead of using the system security libraries.

This setting is set to false by default on all platforms.

Trappable Errors (class ipworks.rshell)

RShell Errors


	118 Firewall error. The error message contains a detailed description.

TCPClient Errors


	100 You cannot change the RemotePort at this time. A connection is in progress.
	101 You cannot change the RemoteHost (Server) at this time. A connection is in progress.
	102 The RemoteHost address is invalid (0.0.0.0).
	104 Already connected. If you want to reconnect, close the current connection first.
	106 You cannot change the LocalPort at this time. A connection is in progress.
	107 You cannot change the LocalHost at this time. A connection is in progress.
	112 You cannot change MaxLineLength at this time. A connection is in progress.
	116 RemotePort cannot be zero. Please specify a valid service port number.
	117 You cannot change the UseConnection option while the class is active.
	135 Operation would block.
	201 Timeout.
	211 Action impossible in control's present state.
	212 Action impossible while not connected.
	213 Action impossible while listening.
	301 Timeout.
	302 Could not open file.
	434 Unable to convert string to selected CodePage.
	1105 Already connecting. If you want to reconnect, close the current connection first.
	1117 You need to connect first.
	1119 You cannot change the LocalHost at this time. A connection is in progress.
	1120 Connection dropped by remote host.

SSL Errors


	270 Cannot load specified security library.
	271 Cannot open certificate store.
	272 Cannot find specified certificate.
	273 Cannot acquire security credentials.
	274 Cannot find certificate chain.
	275 Cannot verify certificate chain.
	276 Error during handshake.
	280 Error verifying certificate.
	281 Could not find client certificate.
	282 Could not find server certificate.
	283 Error encrypting data.
	284 Error decrypting data.

TCP/IP Errors


	10004 [10004] Interrupted system call.
	10009 [10009] Bad file number.
	10013 [10013] Access denied.
	10014 [10014] Bad address.
	10022 [10022] Invalid argument.
	10024 [10024] Too many open files.
	10035 [10035] Operation would block.
	10036 [10036] Operation now in progress.
	10037 [10037] Operation already in progress.
	10038 [10038] Socket operation on non-socket.
	10039 [10039] Destination address required.
	10040 [10040] Message too long.
	10041 [10041] Protocol wrong type for socket.
	10042 [10042] Bad protocol option.
	10043 [10043] Protocol not supported.
	10044 [10044] Socket type not supported.
	10045 [10045] Operation not supported on socket.
	10046 [10046] Protocol family not supported.
	10047 [10047] Address family not supported by protocol family.
	10048 [10048] Address already in use.
	10049 [10049] Can't assign requested address.
	10050 [10050] Network is down.
	10051 [10051] Network is unreachable.
	10052 [10052] Net dropped connection or reset.
	10053 [10053] Software caused connection abort.
	10054 [10054] Connection reset by peer.
	10055 [10055] No buffer space available.
	10056 [10056] Socket is already connected.
	10057 [10057] Socket is not connected.
	10058 [10058] Can't send after socket shutdown.
	10059 [10059] Too many references, can't splice.
	10060 [10060] Connection timed out.
	10061 [10061] Connection refused.
	10062 [10062] Too many levels of symbolic links.
	10063 [10063] File name too long.
	10064 [10064] Host is down.
	10065 [10065] No route to host.
	10066 [10066] Directory not empty
	10067 [10067] Too many processes.
	10068 [10068] Too many users.
	10069 [10069] Disc Quota Exceeded.
	10070 [10070] Stale NFS file handle.
	10071 [10071] Too many levels of remote in path.
	10091 [10091] Network subsystem is unavailable.
	10092 [10092] WINSOCK DLL Version out of range.
	10093 [10093] Winsock not loaded yet.
	11001 [11001] Host not found.
	11002 [11002] Non-authoritative 'Host not found' (try again or check DNS setup).
	11003 [11003] Non-recoverable errors: FORMERR, REFUSED, NOTIMP.
	11004 [11004] Valid name, no data record (check DNS setup).