MQTT Component

Properties   Methods   Events   Config Settings   Errors  

A lightweight, fully-featured MQTT client implementation.

Syntax

TipqMQTT

Remarks

The MQTT component provides a lightweight, fully-featured MQTT client implementation with support for versions 3.1.1 and 5.0. The component supports plaintext and TLS-enabled connections over both standard TCP and WebSockets.

Connecting

When connecting to an MQTT server, the component sends the following information:

• The values of the ClientId, CleanSession, and KeepAliveInterval properties.
• The value of the User property (if non-empty).
• The value of the Password property (if non-empty).
• The values of the WillTopic and WillMessage properties and the WillQOS and WillRetain configuration settings.
• MQTT 5 specific values from ClientTopicAliasMax, SessionExpInterval, ConnectProperties and WillProperties.

If CleanSession is True, check the SessionPresent configuration setting once connected to determine whether the server actually had any session state saved.

Refer to CleanSession, SaveSession, and RestoreSession for more information about MQTT sessions and session state persistence; refer to WillTopic, WillMessage, WillQOS, and WillRetain for more information about MQTT Wills.

Basic Connection Example mqtt1.ClientId = "testClient"; mqtt1.CleanSession = true; mqtt1.KeepAliveInterval = 30; mqtt1.WillTopic = "wills/" + mqtt1.ClientId; mqtt1.WillMessage = mqtt1.ClientId + " was disconnected ungracefully!"; mqtt1.ConnectTo("mqtt.test-server.com", 1883);

Topic Subscriptions

When subscribing, pass one or more topic filters and QoS levels to indicate the topics to subscribe to and the desired QoS level(s). Topic filters may contain wildcards in order to match multiple topics on the server.

Subscribe Examples // Subscribed event handler. mqtt1.OnSubscribed += (s, e) => { if (e.ResponseCode <= 2) Console.WriteLine("Subscribed to " + e.TopicFilter + " at QoS " + e.QOS + "."); else Console.WriteLine("Failed to subscribe to " + e.TopicFilter + "."); }; // Basic, subscribe to some topic filters, all at the same QoS level. mqtt1.Subscribe("home,home/floor1/+/temperature,home/floor2/#", 2); // A bit more advanced, subscribe to the same topic filters, but at different QoS levels. mqtt1.Config("TopicQOSArray=1,2,2"); // The 0 is ignored here since we've specified individual QoS values explicitly. mqtt1.Subscribe("home,home/floor1/+/temperature,home/floor2/#", 0);

After subscribing to topics, any messages received will cause the MessageIn, and potentially also the MessageAck, events to fire. Refer to those events for more information about processing steps for inbound messages.

When unsubscribing, pass the exact same topic filter that was used to subscribe.

Unsubscribe Example // Unsubscribe from topic filters; have to use the exact same strings as before. If this // was to be called after calling the code example shown for the Subscribe() method, we // would still be subscribed to the "home" topic filter. mqtt1.Unsubscribe("home/floor1/+/temperature,home/floor2/#");

Refer to Subscribe and Unsubscribe for more information about subscriptions and topic filters.

Publishing Messages

PublishMessage is used to publish a message with a string payload, while PublishData is used to publish a message with a raw data payload. Both also accept the name of a topic to publish to, and a QoS level at which to publish.

Publish Examples // Publish a simple string-based message. mqtt1.PublishMessage("/home/floor1/security/camera2", 1, "Cat detected!"); // Publish a raw data message. byte[] catPicture = ...; mqtt1.PublishData("/home/floor1/security/camera2", 1, catPicture);

Refer to PublishData and PublishMessage for more information about message publishing and processing steps for outbound messages, as well as topic naming.

MQTT 5 Notes

MQTT 5 is similar to v3.1.1, with a few changes and several new features. Major differences include:

• The Clean Session flag functionality is divided into two properties to allow for finer control over session state data: the Clean Start flag (see CleanSession) and the new SessionExpInterval.
• All response packets (CONNACK, PUBACK, PUBREC, PUBREL, PUBCOMP, SUBACK, UNSUBACK, DISCONNECT) now contain a reason code describing why operations succeeded or failed. See MessageAck, Subscribed, Unsubscribed, and DisconnectReasonCode for details.
• The Request / Response pattern is formalized by the addition of the ResponseTopic. Additional properties such as correlation data and be specified via OutgoingMessageProperties and ConnectProperties.
• New subscription features: Shared Subscriptions, Subscription Options, and SubscriptionIdentifier (see Subscribe for details).
• Topic Aliases can be sent by both client and server to refer to topic filters by shorter numerical identifiers in order to save bandwidth (see TopicAlias, ServerTopicAliasMax and ClientTopicAliasMax).
• Servers can communicate what features it supports in ConnAckProperties.
• More: message expiration (OutgoingMessageProperties), Receive Maximums and Maximum Packet Sizes (ConnectProperties and ConnAckProperties), and a Will Delay interval (WillProperties) are all supported.

Property List

The following is the full list of the properties of the component with short descriptions. Click on the links for further details.

Method List

The following is the full list of the methods of the component with short descriptions. Click on the links for further details.

Event List

The following is the full list of the events fired by the component with short descriptions. Click on the links for further details.

Config Settings

The following is a list of config settings for the component with short descriptions. Click on the links for further details.

CleanSession Property (MQTT Component)

Determines whether a clean session is used once connected.

Syntax

__property bool CleanSession = { read=FCleanSession, write=FSetCleanSession };

Default Value

true

Remarks

This property determines whether or not the component should instruct the server to use a clean session when it connects. (Note that this property must be set to the desired value before calling Connect.)

By default, CleanSession is true, so the server will discard any state data previously associated with the current ClientId once the component has connected successfully. In addition, the server will not save any state data when the component disconnects.

Setting CleanSession to False before connecting will cause the server to re-associate any previously stored state data for the current ClientId. The server will also save any state data that exists when the component is disconnected.

The server-side session state consists of:

• whether a session is present (see SessionPresent),
• client subscriptions (including subscription identifiers in MQTT 5),
• QoS 1 and 2 messages sent to the client pending transmission or completed acknowledgment (and optionally pending QoS 0 messages),
• QoS 2 messages received from the client but not completely acknowledged, and
• the SessionExpInterval (in MQTT 5).

Note that retained messages are not deleted as a result of a session ending, but are not part of the session state.

Client-Side Session State

When setting CleanSession to False, it is important that the RestoreSession method be used to load any previously saved (client-side) session data from a previous session before calling Connect. (Successful calls to RestoreSession will automatically set CleanSession to False.)

Similarly, once disconnected, save the string returned by SaveSession for later use. The saved session information may be used when connecting with CleanSession set to False at a later time.

The client-side session state consists of:

• QoS 1 and QoS 2 messages which have been sent to the Server, but have not been completely acknowledged, and
• QoS 2 messages which have been received from the Server, but have not been completely acknowledged.

Refer to SaveSession and RestoreSession for more information.

MQTT 5 Notes

In MQTT 5, the "Clean Session" flag from v3.1.1 is split into a "Clean Start" flag indicating that the server should discard previously saved session data from this connection, and a SessionExpInterval controlling the length of time the server should preserve the session data after disconnection.

In MQTT 5, this property acts only as the "Clean Start" flag. It determines whether or not the component should instruct the server to discard any previously stored session data associated with the current ClientId and start a new clean session.

For more information on session expiration in MQTT 5, see the SessionExpInterval config. Setting CleanSession to True in v3.1.1 is equivalent to setting CleanSession to True AND setting SessionExpInterval to 0 in MQTT 5.

As with MQTT 3.1.1, it is important for the client to save and restore its own session data on connection and disconnection depending on the value of CleanSession, and to manage its preservation depending on SessionExpInterval.

This property is not available at design time.

Data Type

Boolean

ClientId Property (MQTT Component)

A string that uniquely identifies this instance of the component to the server.

Syntax

__property String ClientId = { read=FClientId, write=FSetClientId };

Default Value

""

Remarks

The ClientId string is used by the server to uniquely identify each client that is connected to it. In MQTT 5, when the SessionExpInterval config is set to a positive value, the server will also associate it with any session state data that needs to be saved for the length of time specified when the component is disconnected.

If ClientId is empty when Connect is called, the component's behavior depends on value of CleanSession. If CleanSession is True, the component will automatically generate a unique value for ClientId before connecting. If CleanSession is False, the component raises an exception.

This property is not available at design time.

Data Type

String

Connected Property (MQTT Component)

Triggers a connection or disconnection.

Syntax

__property bool Connected = { read=FConnected, write=FSetConnected };

Default Value

False

Remarks

This property triggers a connection or disconnection. Setting this property to True makes the component attempt to connect to the host identified by the RemoteHost property. If successful, after the connection is achieved the value of the property changes to True and the Connected event is fired.

Setting this property to False closes the connection.

By default the component will connect in plaintext. To enable SSL set SSLEnabled to True.

In addition, WebSocket connections are supported. To connect using WebSockets specify a hostname beginning with ws:// (plaintext) or wss:// (SSL). For instance, ws://test.mosquitto.org.

When connecting to an MQTT server, the component sends the following information:

• The values of the ClientId, CleanSession, and KeepAliveInterval properties.
• The value of the User property (if non-empty).
• The value of the Password property (if non-empty).
• The values of the WillTopic and WillMessage properties and the WillQOS and WillRetain configuration settings.
• MQTT 5 specific values from ClientTopicAliasMax, SessionExpInterval, ConnectProperties and WillProperties.

If CleanSession is True, check the SessionPresent configuration setting once connected to determine whether the server actually had any session state saved.

Refer to CleanSession, SaveSession, and RestoreSession for more information about MQTT sessions and session state persistence; refer to WillTopic, WillMessage, WillQOS, and WillRetain for more information about MQTT Wills.

Basic Connection Example mqtt1.ClientId = "testClient"; mqtt1.CleanSession = true; mqtt1.KeepAliveInterval = 30; mqtt1.WillTopic = "wills/" + mqtt1.ClientId; mqtt1.WillMessage = mqtt1.ClientId + " was disconnected ungracefully!"; mqtt1.RemoteHost = "mqtt.test-server.com"; mqtt1.RemotePort = 1883; mqtt1.Connect();

This property is not available at design time.

Data Type

Boolean

FirewallAutoDetect Property (MQTT Component)

Whether to automatically detect and use firewall system settings, if available.

Syntax

__property bool FirewallAutoDetect = { read=FFirewallAutoDetect, write=FSetFirewallAutoDetect };

Default Value

False

Remarks

Whether to automatically detect and use firewall system settings, if available.

Data Type

Boolean

FirewallType Property (MQTT Component)

The type of firewall to connect through.

Syntax

__property TipqMQTTFirewallTypes FirewallType = { read=FFirewallType, write=FSetFirewallType };

enum TipqMQTTFirewallTypes {
  fwNone=0,
  fwTunnel=1,
  fwSOCKS4=2,
  fwSOCKS5=3,
  fwSOCKS4A=10
};

Default Value

fwNone

Remarks

The type of firewall to connect through. The applicable values are as follows:

Data Type

Integer

FirewallHost Property (MQTT Component)

The name or IP address of the firewall (optional).

Syntax

__property String FirewallHost = { read=FFirewallHost, write=FSetFirewallHost };

Default Value

""

Remarks

The name or IP address of the firewall (optional). If a FirewallHost is given, the requested connections will be authenticated through the specified firewall when connecting.

If this property is set to a Domain Name, a DNS request is initiated. Upon successful termination of the request, this property is set to the corresponding address. If the search is not successful, the component raises an exception.

Data Type

String

FirewallPassword Property (MQTT Component)

A password if authentication is to be used when connecting through the firewall.

Syntax

__property String FirewallPassword = { read=FFirewallPassword, write=FSetFirewallPassword };

Default Value

""

Remarks

A password if authentication is to be used when connecting through the firewall. If FirewallHost is specified, the FirewallUser and FirewallPassword properties are used to connect and authenticate to the given firewall. If the authentication fails, the component raises an exception.

Data Type

String

FirewallPort Property (MQTT Component)

The Transmission Control Protocol (TCP) port for the firewall Host .

Syntax

__property int FirewallPort = { read=FFirewallPort, write=FSetFirewallPort };

Default Value

0

Remarks

The Transmission Control Protocol (TCP) port for the firewall FirewallHost. See the description of the FirewallHost property for details.

Note: This property is set automatically when FirewallType is set to a valid value. See the description of the FirewallType property for details.

Data Type

Integer

FirewallUser Property (MQTT Component)

A username if authentication is to be used when connecting through a firewall.

Syntax

__property String FirewallUser = { read=FFirewallUser, write=FSetFirewallUser };

Default Value

""

Remarks

A username if authentication is to be used when connecting through a firewall. If FirewallHost is specified, this property and the FirewallPassword property are used to connect and authenticate to the given Firewall. If the authentication fails, the component raises an exception.

Data Type

String

IncomingMessageCount Property (MQTT Component)

The number of records in the IncomingMessage arrays.

Syntax

__property int IncomingMessageCount = { read=FIncomingMessageCount };

Default Value

0

Remarks

This property controls the size of the following arrays:

• IncomingMessageContentType
• IncomingMessageCorrelationData
• IncomingMessageDuplicate
• IncomingMessageMessage
• IncomingMessageMessageExpInterval
• IncomingMessagePacketId
• IncomingMessagePayloadFormatIndicator
• IncomingMessageQoS
• IncomingMessageResponseTopic
• IncomingMessageRetained
• IncomingMessageState
• IncomingMessageSubscriptionIdentifiers
• IncomingMessageTopic
• IncomingMessageTopicAlias

The array indices start at 0 and end at IncomingMessageCount - 1.

This property is read-only and not available at design time.

Data Type

Integer

IncomingMessageContentType Property (MQTT Component)

String describing the content of the message.

Syntax

__property String IncomingMessageContentType[int IncomingMessageIndex] = { read=FIncomingMessageContentType };

Default Value

""

Remarks

String describing the content of the message. Defined by the sending and receiving application.

Valid only for MQTT 5.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

IncomingMessageCorrelationData Property (MQTT Component)

Used by the sender of the request message to identify which request the response message is for when it is received.

Syntax

__property String IncomingMessageCorrelationData[int IncomingMessageIndex] = { read=FIncomingMessageCorrelationData };

Default Value

""

Remarks

Used by the sender of the request message to identify which request the response message is for when it is received.

Valid only for MQTT 5.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

IncomingMessageDuplicate Property (MQTT Component)

Whether or not this message's Duplicate flag is set.

Syntax

__property bool IncomingMessageDuplicate[int IncomingMessageIndex] = { read=FIncomingMessageDuplicate };

Default Value

false

Remarks

Whether or not this message's Duplicate flag is set.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Boolean

IncomingMessageMessage Property (MQTT Component)

This message's raw data payload.

Syntax

__property String IncomingMessageMessage[int IncomingMessageIndex] = { read=FIncomingMessageMessage };
__property DynamicArray<Byte> IncomingMessageMessageB[int IncomingMessageIndex] = { read=FIncomingMessageMessageB };

Default Value

""

Remarks

This message's raw data payload.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Byte Array

IncomingMessageMessageExpInterval Property (MQTT Component)

The lifetime of the message in seconds specified by the sender.

Syntax

__property int IncomingMessageMessageExpInterval[int IncomingMessageIndex] = { read=FIncomingMessageMessageExpInterval };

Default Value

0

Remarks

The lifetime of the message in seconds specified by the sender.

For outgoing messages, the value is useful for instructing the server to delete its copies of the message for any subscribers it has not been able to start delivery to.

For incoming messages, the value sent by the server is the lifetime specified by the sender minus the time the message has been waiting in the server.

Valid only for MQTT 5.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

IncomingMessagePacketId Property (MQTT Component)

This message's packet Id.

Syntax

__property int IncomingMessagePacketId[int IncomingMessageIndex] = { read=FIncomingMessagePacketId };

Default Value

0

Remarks

This message's packet Id.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

IncomingMessagePayloadFormatIndicator Property (MQTT Component)

Indicates whether the payload is unspecified bytes or UTF-8 Encoded character data.

Syntax

__property int IncomingMessagePayloadFormatIndicator[int IncomingMessageIndex] = { read=FIncomingMessagePayloadFormatIndicator };

Default Value

0

Remarks

Indicates whether the payload is unspecified bytes or UTF-8 Encoded character data. Possible values are:

Valid only for MQTT 5.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

IncomingMessageQoS Property (MQTT Component)

This message's QoS level.

Syntax

__property int IncomingMessageQoS[int IncomingMessageIndex] = { read=FIncomingMessageQoS };

Default Value

0

Remarks

This message's QoS level. Possible values are:

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

IncomingMessageResponseTopic Property (MQTT Component)

String used as the topic name for a response message.

Syntax

__property String IncomingMessageResponseTopic[int IncomingMessageIndex] = { read=FIncomingMessageResponseTopic };

Default Value

""

Remarks

String used as the topic name for a response message.

Valid only for MQTT 5.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

IncomingMessageRetained Property (MQTT Component)

Whether or not this message's Retain flag is set.

Syntax

__property bool IncomingMessageRetained[int IncomingMessageIndex] = { read=FIncomingMessageRetained };

Default Value

false

Remarks

Whether or not this message's Retain flag is set.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Boolean

IncomingMessageState Property (MQTT Component)

This message's current state.

Syntax

__property int IncomingMessageState[int IncomingMessageIndex] = { read=FIncomingMessageState };

Default Value

0

Remarks

This message's current state.

Possible Outgoing Message States:

Possible Incoming Message States:

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

IncomingMessageSubscriptionIdentifiers Property (MQTT Component)

A comma separated list of any SubscriptionIdentifiers associated with any client subscription(s) that caused this message to be delivered.

Syntax

__property String IncomingMessageSubscriptionIdentifiers[int IncomingMessageIndex] = { read=FIncomingMessageSubscriptionIdentifiers };

Default Value

""

Remarks

A comma separated list of any SubscriptionIdentifiers associated with any client subscription(s) that caused this message to be delivered.

This property is only applicable to incoming messages.

If SubscriptionIdentifier is set when subscribing, it will be included in any messages delivered by the broker for the topics specified in that packet.

See the Subscribe method for more details.

Valid only for MQTT 5.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

IncomingMessageTopic Property (MQTT Component)

This message's topic.

Syntax

__property String IncomingMessageTopic[int IncomingMessageIndex] = { read=FIncomingMessageTopic };

Default Value

""

Remarks

This message's topic.

MQTT 5 Notes:

If this value is empty, the IncomingMessageTopicAlias property holds the assigned alias for the topic.

If this value is not empty and IncomingMessageTopicAlias is non-zero,

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

IncomingMessageTopicAlias Property (MQTT Component)

An integer used to identify the topic instead of the full topic filter in order to reduce the size of the publish packet.

Syntax

__property int IncomingMessageTopicAlias[int IncomingMessageIndex] = { read=FIncomingMessageTopicAlias };

Default Value

0

Remarks

An integer used to identify the topic instead of the full topic filter in order to reduce the size of the publish packet.

If a non-zero topic alias is received, the client should establish a new topic alias mapping or use an existing mapping, depending on whether the IncomingMessageTopic string is empty.

For details on setting topic aliases for outgoing messages, see the TopicAlias configuration setting.

Valid only for MQTT 5.

The IncomingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the IncomingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

KeepAliveInterval Property (MQTT Component)

The maximum period of inactivity the component will allow before sending a keep-alive packet.

Syntax

__property int KeepAliveInterval = { read=FKeepAliveInterval, write=FSetKeepAliveInterval };

Default Value

0

Remarks

The KeepAliveInterval, if set to a non-zero value, is the maximum number of seconds that the component will allow the connection to be idle before sending a PINGREQ (ping request) packet to the server. The value of KeepAliveInterval is sent to the server when Connect is called; it cannot be changed when the component is already connected.

MQTT servers are required to measure periods of inactivity for all clients who specify a non-zero KeepAliveInterval, and must disconnect them if they have not communicated within 1.5 times KeepAliveInterval.

Similarly, if the component doesn't receive a PINGRESP (ping response) packet within KeepAliveInterval seconds after sending a PINGREQ packet, it will disconnect from the server.

If KeepAliveInterval is set to 0 (default), keep-alive functionality is disabled entirely. In this case, the component will not send any PINGREQ packets, and the server is not required to close the connection due to inactivity.

Note that, regardless of keep-alive settings, the server is always free to disconnect clients it deems "unresponsive".

This property is not available at design time.

Data Type

Integer

LocalHost Property (MQTT Component)

The name of the local host or user-assigned IP interface through which connections are initiated or accepted.

Syntax

__property String LocalHost = { read=FLocalHost, write=FSetLocalHost };

Default Value

""

Remarks

This property contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multihomed hosts (machines with more than one IP interface) setting LocalHost to the IP address of an interface will make the component initiate connections (or accept in the case of server components) only through that interface. It is recommended to provide an IP address rather than a hostname when setting this property to ensure the desired interface is used.

If the component is connected, the LocalHost property shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multihomed hosts (machines with more than one IP interface).

Note: LocalHost is not persistent. You must always set it in code, and never in the property window.

Data Type

String

LocalPort Property (MQTT Component)

The TCP port in the local host where the component binds.

Syntax

__property int LocalPort = { read=FLocalPort, write=FSetLocalPort };

Default Value

0

Remarks

This property must be set before a connection is attempted. It instructs the component to bind to a specific port (or communication endpoint) in the local machine.

Setting this property to 0 (default) enables the system to choose an open port at random. The chosen port will be returned by the LocalPort property after the connection is established.

LocalPort cannot be changed once a connection is made. Any attempt to set this property when a connection is active will generate an error.

This property is useful when trying to connect to services that require a trusted port on the client side.

Data Type

Integer

OutgoingMessageCount Property (MQTT Component)

The number of records in the OutgoingMessage arrays.

Syntax

__property int OutgoingMessageCount = { read=FOutgoingMessageCount };

Default Value

0

Remarks

This property controls the size of the following arrays:

• OutgoingMessageContentType
• OutgoingMessageCorrelationData
• OutgoingMessageDuplicate
• OutgoingMessageMessage
• OutgoingMessageMessageExpInterval
• OutgoingMessagePacketId
• OutgoingMessagePayloadFormatIndicator
• OutgoingMessageQoS
• OutgoingMessageResponseTopic
• OutgoingMessageRetained
• OutgoingMessageState
• OutgoingMessageSubscriptionIdentifiers
• OutgoingMessageTopic
• OutgoingMessageTopicAlias

The array indices start at 0 and end at OutgoingMessageCount - 1.

This property is read-only and not available at design time.

Data Type

Integer

OutgoingMessageContentType Property (MQTT Component)

String describing the content of the message.

Syntax

__property String OutgoingMessageContentType[int OutgoingMessageIndex] = { read=FOutgoingMessageContentType };

Default Value

""

Remarks

String describing the content of the message. Defined by the sending and receiving application.

Valid only for MQTT 5.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

OutgoingMessageCorrelationData Property (MQTT Component)

Used by the sender of the request message to identify which request the response message is for when it is received.

Syntax

__property String OutgoingMessageCorrelationData[int OutgoingMessageIndex] = { read=FOutgoingMessageCorrelationData };

Default Value

""

Remarks

Used by the sender of the request message to identify which request the response message is for when it is received.

Valid only for MQTT 5.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

OutgoingMessageDuplicate Property (MQTT Component)

Whether or not this message's Duplicate flag is set.

Syntax

__property bool OutgoingMessageDuplicate[int OutgoingMessageIndex] = { read=FOutgoingMessageDuplicate };

Default Value

false

Remarks

Whether or not this message's Duplicate flag is set.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Boolean

OutgoingMessageMessage Property (MQTT Component)

This message's raw data payload.

Syntax

__property String OutgoingMessageMessage[int OutgoingMessageIndex] = { read=FOutgoingMessageMessage };
__property DynamicArray<Byte> OutgoingMessageMessageB[int OutgoingMessageIndex] = { read=FOutgoingMessageMessageB };

Default Value

""

Remarks

This message's raw data payload.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Byte Array

OutgoingMessageMessageExpInterval Property (MQTT Component)

The lifetime of the message in seconds specified by the sender.

Syntax

__property int OutgoingMessageMessageExpInterval[int OutgoingMessageIndex] = { read=FOutgoingMessageMessageExpInterval };

Default Value

0

Remarks

The lifetime of the message in seconds specified by the sender.

For outgoing messages, the value is useful for instructing the server to delete its copies of the message for any subscribers it has not been able to start delivery to.

For incoming messages, the value sent by the server is the lifetime specified by the sender minus the time the message has been waiting in the server.

Valid only for MQTT 5.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

OutgoingMessagePacketId Property (MQTT Component)

This message's packet Id.

Syntax

__property int OutgoingMessagePacketId[int OutgoingMessageIndex] = { read=FOutgoingMessagePacketId };

Default Value

0

Remarks

This message's packet Id.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

OutgoingMessagePayloadFormatIndicator Property (MQTT Component)

Indicates whether the payload is unspecified bytes or UTF-8 Encoded character data.

Syntax

__property int OutgoingMessagePayloadFormatIndicator[int OutgoingMessageIndex] = { read=FOutgoingMessagePayloadFormatIndicator };

Default Value

0

Remarks

Indicates whether the payload is unspecified bytes or UTF-8 Encoded character data. Possible values are:

Valid only for MQTT 5.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

OutgoingMessageQoS Property (MQTT Component)

This message's QoS level.

Syntax

__property int OutgoingMessageQoS[int OutgoingMessageIndex] = { read=FOutgoingMessageQoS };

Default Value

0

Remarks

This message's QoS level. Possible values are:

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

OutgoingMessageResponseTopic Property (MQTT Component)

String used as the topic name for a response message.

Syntax

__property String OutgoingMessageResponseTopic[int OutgoingMessageIndex] = { read=FOutgoingMessageResponseTopic };

Default Value

""

Remarks

String used as the topic name for a response message.

Valid only for MQTT 5.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

OutgoingMessageRetained Property (MQTT Component)

Whether or not this message's Retain flag is set.

Syntax

__property bool OutgoingMessageRetained[int OutgoingMessageIndex] = { read=FOutgoingMessageRetained };

Default Value

false

Remarks

Whether or not this message's Retain flag is set.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Boolean

OutgoingMessageState Property (MQTT Component)

This message's current state.

Syntax

__property int OutgoingMessageState[int OutgoingMessageIndex] = { read=FOutgoingMessageState };

Default Value

0

Remarks

This message's current state.

Possible Outgoing Message States:

Possible Incoming Message States:

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

OutgoingMessageSubscriptionIdentifiers Property (MQTT Component)

A comma separated list of any SubscriptionIdentifiers associated with any client subscription(s) that caused this message to be delivered.

Syntax

__property String OutgoingMessageSubscriptionIdentifiers[int OutgoingMessageIndex] = { read=FOutgoingMessageSubscriptionIdentifiers };

Default Value

""

Remarks

A comma separated list of any SubscriptionIdentifiers associated with any client subscription(s) that caused this message to be delivered.

This property is only applicable to incoming messages.

If SubscriptionIdentifier is set when subscribing, it will be included in any messages delivered by the broker for the topics specified in that packet.

See the Subscribe method for more details.

Valid only for MQTT 5.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

OutgoingMessageTopic Property (MQTT Component)

This message's topic.

Syntax

__property String OutgoingMessageTopic[int OutgoingMessageIndex] = { read=FOutgoingMessageTopic };

Default Value

""

Remarks

This message's topic.

MQTT 5 Notes:

If this value is empty, the OutgoingMessageTopicAlias property holds the assigned alias for the topic.

If this value is not empty and OutgoingMessageTopicAlias is non-zero,

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

String

OutgoingMessageTopicAlias Property (MQTT Component)

An integer used to identify the topic instead of the full topic filter in order to reduce the size of the publish packet.

Syntax

__property int OutgoingMessageTopicAlias[int OutgoingMessageIndex] = { read=FOutgoingMessageTopicAlias };

Default Value

0

Remarks

An integer used to identify the topic instead of the full topic filter in order to reduce the size of the publish packet.

If a non-zero topic alias is received, the client should establish a new topic alias mapping or use an existing mapping, depending on whether the OutgoingMessageTopic string is empty.

For details on setting topic aliases for outgoing messages, see the TopicAlias configuration setting.

Valid only for MQTT 5.

The OutgoingMessageIndex parameter specifies the index of the item in the array. The size of the array is controlled by the OutgoingMessageCount property.

This property is read-only and not available at design time.

Data Type

Integer

Password Property (MQTT Component)

A password if authentication is to be used.

Syntax

__property String Password = { read=FPassword, write=FSetPassword };

Default Value

""

Remarks

This property can be set to a password if authentication is to be used.

In MQTT 3.1.1, while a User may be specified without a Password, setting a Password without a User is not supported; attempting to do so will cause the server to reject the connection attempt.

In MQTT 5, a Password may be set without a User, allowing the field to be used for credentials other than a password.

This property is not available at design time.

Data Type

String

ReadyToSend Property (MQTT Component)

Indicates whether the component is ready to send data.

Syntax

__property bool ReadyToSend = { read=FReadyToSend };

Default Value

false

Remarks

This property indicates that the underlying TCP/IP subsystem is ready to accept data. This is True after connecting to the remote host, and will become False if a call to PublishData or PublishMessage fails due to a WOULDBLOCK condition.

Once data can be sent again, the ReadyToSend event will fire and this property will be True.

If a WOULDBLOCK error occurs while sending a message the component will automatically complete the transmission when sending is possible. No action needs to be taken to re-send the message. ReadyToSend will fire after the component completes any partially sent messages.

This property is read-only and not available at design time.

Data Type

Boolean

RemoteHost Property (MQTT Component)

The address of the remote host. Domain names are resolved to IP addresses.

Syntax

__property String RemoteHost = { read=FRemoteHost, write=FSetRemoteHost };

Default Value

""

Remarks

This property specifies the IP address (IP number in dotted internet format) or Domain Name of the remote host. It is set before a connection is attempted and cannot be changed once a connection is established.

If this property is set to a Domain Name, a DNS request is initiated, and upon successful termination of the request, this property is set to the corresponding address. If the search is not successful, an error is returned.

If the component is configured to use a SOCKS firewall, the value assigned to this property may be preceded with an "*". If this is the case, the host name is passed to the firewall unresolved and the firewall performs the DNS resolution.

By default the component will connect in plaintext. To enable SSL set SSLEnabled to True.

In addition, WebSocket connections are supported. To connect using WebSockets specify a hostname beginning with ws:// (plaintext) or wss:// (SSL). For instance, ws://test.mosquitto.org.

Data Type

String

RemotePort Property (MQTT Component)

The port of the MQTT server (default is 1883). The default port for SSL is 8883.

Syntax

__property int RemotePort = { read=FRemotePort, write=FSetRemotePort };

Default Value

1883

Remarks

This property specifies a service port on the remote host to connect to.

A valid port number (a value between 1 and 65535) is required for the connection to take place. The property must be set before a connection is attempted and cannot be changed once a connection is established. Any attempt to change this property while connected will fail with an error.

This property is not available at design time.

Data Type

Integer

SSLAcceptServerCertEffectiveDate Property (MQTT Component)

The date on which this certificate becomes valid.

Syntax

__property String SSLAcceptServerCertEffectiveDate = { read=FSSLAcceptServerCertEffectiveDate };

Default Value

""

Remarks

The date on which this certificate becomes valid. Before this date, it is not valid. The date is localized to the system's time zone. The following example illustrates the format of an encoded date:

23-Jan-2000 15:00:00.

This property is read-only.

Data Type

String

SSLAcceptServerCertExpirationDate Property (MQTT Component)

The date on which the certificate expires.

Syntax

__property String SSLAcceptServerCertExpirationDate = { read=FSSLAcceptServerCertExpirationDate };

Default Value

""

Remarks

The date on which the certificate expires. After this date, the certificate will no longer be valid. The date is localized to the system's time zone. The following example illustrates the format of an encoded date:

23-Jan-2001 15:00:00.

This property is read-only.

Data Type

String

SSLAcceptServerCertExtendedKeyUsage Property (MQTT Component)

A comma-delimited list of extended key usage identifiers.

Syntax

__property String SSLAcceptServerCertExtendedKeyUsage = { read=FSSLAcceptServerCertExtendedKeyUsage };

Default Value

""

Remarks

A comma-delimited list of extended key usage identifiers. These are the same as ASN.1 object identifiers (OIDs).

This property is read-only.

Data Type

String

SSLAcceptServerCertFingerprint Property (MQTT Component)

The hex-encoded, 16-byte MD5 fingerprint of the certificate.

Syntax

__property String SSLAcceptServerCertFingerprint = { read=FSSLAcceptServerCertFingerprint };

Default Value

""

Remarks

The hex-encoded, 16-byte MD5 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: bc:2a:72:af:fe:58:17:43:7a:5f:ba:5a:7c:90:f7:02

This property is read-only.

Data Type

String

SSLAcceptServerCertFingerprintSHA1 Property (MQTT Component)

The hex-encoded, 20-byte SHA-1 fingerprint of the certificate.

Syntax

__property String SSLAcceptServerCertFingerprintSHA1 = { read=FSSLAcceptServerCertFingerprintSHA1 };

Default Value

""

Remarks

The hex-encoded, 20-byte SHA-1 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 30:7b:fa:38:65:83:ff:da:b4:4e:07:3f:17:b8:a4:ed:80:be:ff:84

This property is read-only.

Data Type

String

SSLAcceptServerCertFingerprintSHA256 Property (MQTT Component)

The hex-encoded, 32-byte SHA-256 fingerprint of the certificate.

Syntax

__property String SSLAcceptServerCertFingerprintSHA256 = { read=FSSLAcceptServerCertFingerprintSHA256 };

Default Value

""

Remarks

The hex-encoded, 32-byte SHA-256 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 6a:80:5c:33:a9:43:ea:b0:96:12:8a:64:96:30:ef:4a:8a:96:86:ce:f4:c7:be:10:24:8e:2b:60:9e:f3:59:53

This property is read-only.

Data Type

String

SSLAcceptServerCertIssuer Property (MQTT Component)

The issuer of the certificate.

Syntax

__property String SSLAcceptServerCertIssuer = { read=FSSLAcceptServerCertIssuer };

Default Value

""

Remarks

The issuer of the certificate. This property contains a string representation of the name of the issuing authority for the certificate.

This property is read-only.

Data Type

String

SSLAcceptServerCertPrivateKey Property (MQTT Component)

The private key of the certificate (if available).

Syntax

__property String SSLAcceptServerCertPrivateKey = { read=FSSLAcceptServerCertPrivateKey };

Default Value

""

Remarks

The private key of the certificate (if available). The key is provided as PEM/Base64-encoded data.

Note: The SSLAcceptServerCertPrivateKey may be available but not exportable. In this case, SSLAcceptServerCertPrivateKey returns an empty string.

This property is read-only.

Data Type

String

SSLAcceptServerCertPrivateKeyAvailable Property (MQTT Component)

Whether a PrivateKey is available for the selected certificate.

Syntax

__property bool SSLAcceptServerCertPrivateKeyAvailable = { read=FSSLAcceptServerCertPrivateKeyAvailable };

Default Value

false

Remarks

Whether a SSLAcceptServerCertPrivateKey is available for the selected certificate. If SSLAcceptServerCertPrivateKeyAvailable is True, the certificate may be used for authentication purposes (e.g., server authentication).

This property is read-only.

Data Type

Boolean

SSLAcceptServerCertPrivateKeyContainer Property (MQTT Component)

The name of the PrivateKey container for the certificate (if available).

Syntax

__property String SSLAcceptServerCertPrivateKeyContainer = { read=FSSLAcceptServerCertPrivateKeyContainer };

Default Value

""

Remarks

The name of the SSLAcceptServerCertPrivateKey container for the certificate (if available). This functionality is available only on Windows platforms.

This property is read-only.

Data Type

String

SSLAcceptServerCertPublicKey Property (MQTT Component)

The public key of the certificate.

Syntax

__property String SSLAcceptServerCertPublicKey = { read=FSSLAcceptServerCertPublicKey };

Default Value

""

Remarks

The public key of the certificate. The key is provided as PEM/Base64-encoded data.

This property is read-only.

Data Type

String

SSLAcceptServerCertPublicKeyAlgorithm Property (MQTT Component)

The textual description of the certificate's public key algorithm.

Syntax

__property String SSLAcceptServerCertPublicKeyAlgorithm = { read=FSSLAcceptServerCertPublicKeyAlgorithm };

Default Value

""

Remarks

The textual description of the certificate's public key algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_DH") or an object identifier (OID) string representing the algorithm.

This property is read-only.

Data Type

String

SSLAcceptServerCertPublicKeyLength Property (MQTT Component)

The length of the certificate's public key (in bits).

Syntax

__property int SSLAcceptServerCertPublicKeyLength = { read=FSSLAcceptServerCertPublicKeyLength };

Default Value

0

Remarks

The length of the certificate's public key (in bits). Common values are 512, 1024, and 2048.

This property is read-only.

Data Type

Integer

SSLAcceptServerCertSerialNumber Property (MQTT Component)

The serial number of the certificate encoded as a string.

Syntax

__property String SSLAcceptServerCertSerialNumber = { read=FSSLAcceptServerCertSerialNumber };

Default Value

""

Remarks

The serial number of the certificate encoded as a string. The number is encoded as a series of hexadecimal digits, with each pair representing a byte of the serial number.

This property is read-only.

Data Type

String

SSLAcceptServerCertSignatureAlgorithm Property (MQTT Component)

The text description of the certificate's signature algorithm.

Syntax

__property String SSLAcceptServerCertSignatureAlgorithm = { read=FSSLAcceptServerCertSignatureAlgorithm };

Default Value

""

Remarks

The text description of the certificate's signature algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_MD5RSA") or an object identifier (OID) string representing the algorithm.

This property is read-only.

Data Type

String

SSLAcceptServerCertStore Property (MQTT Component)

The name of the certificate store for the client certificate.

Syntax

__property String SSLAcceptServerCertStore = { read=FSSLAcceptServerCertStore, write=FSetSSLAcceptServerCertStore };
__property DynamicArray<Byte> SSLAcceptServerCertStoreB = { read=FSSLAcceptServerCertStoreB, write=FSetSSLAcceptServerCertStoreB };

Default Value

"MY"

Remarks

The name of the certificate store for the client certificate.

The SSLAcceptServerCertStoreType property denotes the type of the certificate store specified by SSLAcceptServerCertStore. If the store is password-protected, specify the password in SSLAcceptServerCertStorePassword.

SSLAcceptServerCertStore is used in conjunction with the SSLAcceptServerCertSubject property to specify client certificates. If SSLAcceptServerCertStore has a value, and SSLAcceptServerCertSubject or SSLAcceptServerCertEncoded is set, a search for a certificate is initiated. Please see the SSLAcceptServerCertSubject property for details.

Designations of certificate stores are platform dependent.

The following designations are the most common User and Machine certificate stores in Windows:

When the certificate store type is cstPFXFile, this property must be set to the name of the file. When the type is cstPFXBlob, the property must be set to the binary contents of a PFX file (i.e., PKCS#12 certificate store).

Data Type

Byte Array

SSLAcceptServerCertStorePassword Property (MQTT Component)

If the type of certificate store requires a password, this property is used to specify the password needed to open the certificate store.

Syntax

__property String SSLAcceptServerCertStorePassword = { read=FSSLAcceptServerCertStorePassword, write=FSetSSLAcceptServerCertStorePassword };

Default Value

""

Remarks

If the type of certificate store requires a password, this property is used to specify the password needed to open the certificate store.

Data Type

String

SSLAcceptServerCertStoreType Property (MQTT Component)

The type of certificate store for this certificate.

Syntax

__property TipqMQTTSSLAcceptServerCertStoreTypes SSLAcceptServerCertStoreType = { read=FSSLAcceptServerCertStoreType, write=FSetSSLAcceptServerCertStoreType };

enum TipqMQTTSSLAcceptServerCertStoreTypes {
  cstUser=0,
  cstMachine=1,
  cstPFXFile=2,
  cstPFXBlob=3,
  cstJKSFile=4,
  cstJKSBlob=5,
  cstPEMKeyFile=6,
  cstPEMKeyBlob=7,
  cstPublicKeyFile=8,
  cstPublicKeyBlob=9,
  cstSSHPublicKeyBlob=10,
  cstP7BFile=11,
  cstP7BBlob=12,
  cstSSHPublicKeyFile=13,
  cstPPKFile=14,
  cstPPKBlob=15,
  cstXMLFile=16,
  cstXMLBlob=17,
  cstJWKFile=18,
  cstJWKBlob=19,
  cstSecurityKey=20,
  cstBCFKSFile=21,
  cstBCFKSBlob=22,
  cstPKCS11=23,
  cstAuto=99
};

Default Value

cstUser

Remarks

The type of certificate store for this certificate.

The component supports both public and private keys in a variety of formats. When the cstAuto value is used, the component will automatically determine the type. This property can take one of the following values:

Data Type

Integer

SSLAcceptServerCertSubjectAltNames Property (MQTT Component)

Comma-separated lists of alternative subject names for the certificate.

Syntax

__property String SSLAcceptServerCertSubjectAltNames = { read=FSSLAcceptServerCertSubjectAltNames };

Default Value

""

Remarks

Comma-separated lists of alternative subject names for the certificate.

This property is read-only.

Data Type

String

SSLAcceptServerCertThumbprintMD5 Property (MQTT Component)

The MD5 hash of the certificate.

Syntax

__property String SSLAcceptServerCertThumbprintMD5 = { read=FSSLAcceptServerCertThumbprintMD5 };

Default Value

""

Remarks

The MD5 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLAcceptServerCertThumbprintSHA1 Property (MQTT Component)

The SHA-1 hash of the certificate.

Syntax

__property String SSLAcceptServerCertThumbprintSHA1 = { read=FSSLAcceptServerCertThumbprintSHA1 };

Default Value

""

Remarks

The SHA-1 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLAcceptServerCertThumbprintSHA256 Property (MQTT Component)

The SHA-256 hash of the certificate.

Syntax

__property String SSLAcceptServerCertThumbprintSHA256 = { read=FSSLAcceptServerCertThumbprintSHA256 };

Default Value

""

Remarks

The SHA-256 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLAcceptServerCertUsage Property (MQTT Component)

The text description of UsageFlags .

Syntax

__property String SSLAcceptServerCertUsage = { read=FSSLAcceptServerCertUsage };

Default Value

""

Remarks

The text description of SSLAcceptServerCertUsageFlags.

This value will be one or more of the following strings and will be separated by commas:

• Digital Signature
• Non-Repudiation
• Key Encipherment
• Data Encipherment
• Key Agreement
• Certificate Signing
• CRL Signing
• Encipher Only

If the provider is OpenSSL, the value is a comma-separated list of X.509 certificate extension names.

This property is read-only.

Data Type

String

SSLAcceptServerCertUsageFlags Property (MQTT Component)

The flags that show intended use for the certificate.

Syntax

__property int SSLAcceptServerCertUsageFlags = { read=FSSLAcceptServerCertUsageFlags };

Default Value

0

Remarks

The flags that show intended use for the certificate. The value of SSLAcceptServerCertUsageFlags is a combination of the following flags:

Please see the SSLAcceptServerCertUsage property for a text representation of SSLAcceptServerCertUsageFlags.

This functionality currently is not available when the provider is OpenSSL.

This property is read-only.

Data Type

Integer

SSLAcceptServerCertVersion Property (MQTT Component)

The certificate's version number.

Syntax

__property String SSLAcceptServerCertVersion = { read=FSSLAcceptServerCertVersion };

Default Value

""

Remarks

The certificate's version number. The possible values are the strings "V1", "V2", and "V3".

This property is read-only.

Data Type

String

SSLAcceptServerCertSubject Property (MQTT Component)

The subject of the certificate used for client authentication.

Syntax

__property String SSLAcceptServerCertSubject = { read=FSSLAcceptServerCertSubject, write=FSetSSLAcceptServerCertSubject };

Default Value

""

Remarks

The subject of the certificate used for client authentication.

This property must be set after all other certificate properties are set. When this property is set, a search is performed in the current certificate store to locate a certificate with a matching subject.

If a matching certificate is found, the property is set to the full subject of the matching certificate.

If an exact match is not found, the store is searched for subjects containing the value of the property.

If a match is still not found, the property is set to an empty string, and no certificate is selected.

The special value "*" picks a random certificate in the certificate store.

The certificate subject is a comma-separated list of distinguished name fields and values. For instance, "CN=www.server.com, OU=test, C=US, E=support@nsoftware.com". Common fields and their meanings are as follows:

If a field value contains a comma, it must be quoted.

Data Type

String

SSLAcceptServerCertEncoded Property (MQTT Component)

The certificate (PEM/Base64 encoded).

Syntax

__property String SSLAcceptServerCertEncoded = { read=FSSLAcceptServerCertEncoded, write=FSetSSLAcceptServerCertEncoded };
__property DynamicArray<Byte> SSLAcceptServerCertEncodedB = { read=FSSLAcceptServerCertEncodedB, write=FSetSSLAcceptServerCertEncodedB };

Default Value

""

Remarks

The certificate (PEM/Base64 encoded). This property is used to assign a specific certificate. The SSLAcceptServerCertStore and SSLAcceptServerCertSubject properties also may be used to specify a certificate.

When SSLAcceptServerCertEncoded is set, a search is initiated in the current SSLAcceptServerCertStore for the private key of the certificate. If the key is found, SSLAcceptServerCertSubject is updated to reflect the full subject of the selected certificate; otherwise, SSLAcceptServerCertSubject is set to an empty string.

This property is not available at design time.

Data Type

Byte Array

SSLCertEffectiveDate Property (MQTT Component)

The date on which this certificate becomes valid.

Syntax

__property String SSLCertEffectiveDate = { read=FSSLCertEffectiveDate };

Default Value

""

Remarks

The date on which this certificate becomes valid. Before this date, it is not valid. The date is localized to the system's time zone. The following example illustrates the format of an encoded date:

23-Jan-2000 15:00:00.

This property is read-only.

Data Type

String

SSLCertExpirationDate Property (MQTT Component)

The date on which the certificate expires.

Syntax

__property String SSLCertExpirationDate = { read=FSSLCertExpirationDate };

Default Value

""

Remarks

The date on which the certificate expires. After this date, the certificate will no longer be valid. The date is localized to the system's time zone. The following example illustrates the format of an encoded date:

23-Jan-2001 15:00:00.

This property is read-only.

Data Type

String

SSLCertExtendedKeyUsage Property (MQTT Component)

A comma-delimited list of extended key usage identifiers.

Syntax

__property String SSLCertExtendedKeyUsage = { read=FSSLCertExtendedKeyUsage };

Default Value

""

Remarks

A comma-delimited list of extended key usage identifiers. These are the same as ASN.1 object identifiers (OIDs).

This property is read-only.

Data Type

String

SSLCertFingerprint Property (MQTT Component)

The hex-encoded, 16-byte MD5 fingerprint of the certificate.

Syntax

__property String SSLCertFingerprint = { read=FSSLCertFingerprint };

Default Value

""

Remarks

The hex-encoded, 16-byte MD5 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: bc:2a:72:af:fe:58:17:43:7a:5f:ba:5a:7c:90:f7:02

This property is read-only.

Data Type

String

SSLCertFingerprintSHA1 Property (MQTT Component)

The hex-encoded, 20-byte SHA-1 fingerprint of the certificate.

Syntax

__property String SSLCertFingerprintSHA1 = { read=FSSLCertFingerprintSHA1 };

Default Value

""

Remarks

The hex-encoded, 20-byte SHA-1 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 30:7b:fa:38:65:83:ff:da:b4:4e:07:3f:17:b8:a4:ed:80:be:ff:84

This property is read-only.

Data Type

String

SSLCertFingerprintSHA256 Property (MQTT Component)

The hex-encoded, 32-byte SHA-256 fingerprint of the certificate.

Syntax

__property String SSLCertFingerprintSHA256 = { read=FSSLCertFingerprintSHA256 };

Default Value

""

Remarks

The hex-encoded, 32-byte SHA-256 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 6a:80:5c:33:a9:43:ea:b0:96:12:8a:64:96:30:ef:4a:8a:96:86:ce:f4:c7:be:10:24:8e:2b:60:9e:f3:59:53

This property is read-only.

Data Type

String

SSLCertIssuer Property (MQTT Component)

The issuer of the certificate.

Syntax

__property String SSLCertIssuer = { read=FSSLCertIssuer };

Default Value

""

Remarks

The issuer of the certificate. This property contains a string representation of the name of the issuing authority for the certificate.

This property is read-only.

Data Type

String

SSLCertPrivateKey Property (MQTT Component)

The private key of the certificate (if available).

Syntax

__property String SSLCertPrivateKey = { read=FSSLCertPrivateKey };

Default Value

""

Remarks

The private key of the certificate (if available). The key is provided as PEM/Base64-encoded data.

Note: The SSLCertPrivateKey may be available but not exportable. In this case, SSLCertPrivateKey returns an empty string.

This property is read-only.

Data Type

String

SSLCertPrivateKeyAvailable Property (MQTT Component)

Whether a PrivateKey is available for the selected certificate.

Syntax

__property bool SSLCertPrivateKeyAvailable = { read=FSSLCertPrivateKeyAvailable };

Default Value

false

Remarks

Whether a SSLCertPrivateKey is available for the selected certificate. If SSLCertPrivateKeyAvailable is True, the certificate may be used for authentication purposes (e.g., server authentication).

This property is read-only.

Data Type

Boolean

SSLCertPrivateKeyContainer Property (MQTT Component)

The name of the PrivateKey container for the certificate (if available).

Syntax

__property String SSLCertPrivateKeyContainer = { read=FSSLCertPrivateKeyContainer };

Default Value

""

Remarks

The name of the SSLCertPrivateKey container for the certificate (if available). This functionality is available only on Windows platforms.

This property is read-only.

Data Type

String

SSLCertPublicKey Property (MQTT Component)

The public key of the certificate.

Syntax

__property String SSLCertPublicKey = { read=FSSLCertPublicKey };

Default Value

""

Remarks

The public key of the certificate. The key is provided as PEM/Base64-encoded data.

This property is read-only.

Data Type

String

SSLCertPublicKeyAlgorithm Property (MQTT Component)

The textual description of the certificate's public key algorithm.

Syntax

__property String SSLCertPublicKeyAlgorithm = { read=FSSLCertPublicKeyAlgorithm };

Default Value

""

Remarks

The textual description of the certificate's public key algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_DH") or an object identifier (OID) string representing the algorithm.

This property is read-only.

Data Type

String

SSLCertPublicKeyLength Property (MQTT Component)

The length of the certificate's public key (in bits).

Syntax

__property int SSLCertPublicKeyLength = { read=FSSLCertPublicKeyLength };

Default Value

0

Remarks

The length of the certificate's public key (in bits). Common values are 512, 1024, and 2048.

This property is read-only.

Data Type

Integer

SSLCertSerialNumber Property (MQTT Component)

The serial number of the certificate encoded as a string.

Syntax

__property String SSLCertSerialNumber = { read=FSSLCertSerialNumber };

Default Value

""

Remarks

The serial number of the certificate encoded as a string. The number is encoded as a series of hexadecimal digits, with each pair representing a byte of the serial number.

This property is read-only.

Data Type

String

SSLCertSignatureAlgorithm Property (MQTT Component)

The text description of the certificate's signature algorithm.

Syntax

__property String SSLCertSignatureAlgorithm = { read=FSSLCertSignatureAlgorithm };

Default Value

""

Remarks

The text description of the certificate's signature algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_MD5RSA") or an object identifier (OID) string representing the algorithm.

This property is read-only.

Data Type

String

SSLCertStore Property (MQTT Component)

The name of the certificate store for the client certificate.

Syntax

__property String SSLCertStore = { read=FSSLCertStore, write=FSetSSLCertStore };
__property DynamicArray<Byte> SSLCertStoreB = { read=FSSLCertStoreB, write=FSetSSLCertStoreB };

Default Value

"MY"

Remarks

The name of the certificate store for the client certificate.

The SSLCertStoreType property denotes the type of the certificate store specified by SSLCertStore. If the store is password-protected, specify the password in SSLCertStorePassword.

SSLCertStore is used in conjunction with the SSLCertSubject property to specify client certificates. If SSLCertStore has a value, and SSLCertSubject or SSLCertEncoded is set, a search for a certificate is initiated. Please see the SSLCertSubject property for details.

Designations of certificate stores are platform dependent.

The following designations are the most common User and Machine certificate stores in Windows:

When the certificate store type is cstPFXFile, this property must be set to the name of the file. When the type is cstPFXBlob, the property must be set to the binary contents of a PFX file (i.e., PKCS#12 certificate store).

Data Type

Byte Array

SSLCertStorePassword Property (MQTT Component)

If the type of certificate store requires a password, this property is used to specify the password needed to open the certificate store.

Syntax

__property String SSLCertStorePassword = { read=FSSLCertStorePassword, write=FSetSSLCertStorePassword };

Default Value

""

Remarks

If the type of certificate store requires a password, this property is used to specify the password needed to open the certificate store.

Data Type

String

SSLCertStoreType Property (MQTT Component)

The type of certificate store for this certificate.

Syntax

__property TipqMQTTSSLCertStoreTypes SSLCertStoreType = { read=FSSLCertStoreType, write=FSetSSLCertStoreType };

enum TipqMQTTSSLCertStoreTypes {
  cstUser=0,
  cstMachine=1,
  cstPFXFile=2,
  cstPFXBlob=3,
  cstJKSFile=4,
  cstJKSBlob=5,
  cstPEMKeyFile=6,
  cstPEMKeyBlob=7,
  cstPublicKeyFile=8,
  cstPublicKeyBlob=9,
  cstSSHPublicKeyBlob=10,
  cstP7BFile=11,
  cstP7BBlob=12,
  cstSSHPublicKeyFile=13,
  cstPPKFile=14,
  cstPPKBlob=15,
  cstXMLFile=16,
  cstXMLBlob=17,
  cstJWKFile=18,
  cstJWKBlob=19,
  cstSecurityKey=20,
  cstBCFKSFile=21,
  cstBCFKSBlob=22,
  cstPKCS11=23,
  cstAuto=99
};

Default Value

cstUser

Remarks

The type of certificate store for this certificate.

The component supports both public and private keys in a variety of formats. When the cstAuto value is used, the component will automatically determine the type. This property can take one of the following values:

Data Type

Integer

SSLCertSubjectAltNames Property (MQTT Component)

Comma-separated lists of alternative subject names for the certificate.

Syntax

__property String SSLCertSubjectAltNames = { read=FSSLCertSubjectAltNames };

Default Value

""

Remarks

Comma-separated lists of alternative subject names for the certificate.

This property is read-only.

Data Type

String

SSLCertThumbprintMD5 Property (MQTT Component)

The MD5 hash of the certificate.

Syntax

__property String SSLCertThumbprintMD5 = { read=FSSLCertThumbprintMD5 };

Default Value

""

Remarks

The MD5 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLCertThumbprintSHA1 Property (MQTT Component)

The SHA-1 hash of the certificate.

Syntax

__property String SSLCertThumbprintSHA1 = { read=FSSLCertThumbprintSHA1 };

Default Value

""

Remarks

The SHA-1 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLCertThumbprintSHA256 Property (MQTT Component)

The SHA-256 hash of the certificate.

Syntax

__property String SSLCertThumbprintSHA256 = { read=FSSLCertThumbprintSHA256 };

Default Value

""

Remarks

The SHA-256 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLCertUsage Property (MQTT Component)

The text description of UsageFlags .

Syntax

__property String SSLCertUsage = { read=FSSLCertUsage };

Default Value

""

Remarks

The text description of SSLCertUsageFlags.

This value will be one or more of the following strings and will be separated by commas:

• Digital Signature
• Non-Repudiation
• Key Encipherment
• Data Encipherment
• Key Agreement
• Certificate Signing
• CRL Signing
• Encipher Only

If the provider is OpenSSL, the value is a comma-separated list of X.509 certificate extension names.

This property is read-only.

Data Type

String

SSLCertUsageFlags Property (MQTT Component)

The flags that show intended use for the certificate.

Syntax

__property int SSLCertUsageFlags = { read=FSSLCertUsageFlags };

Default Value

0

Remarks

The flags that show intended use for the certificate. The value of SSLCertUsageFlags is a combination of the following flags:

Please see the SSLCertUsage property for a text representation of SSLCertUsageFlags.

This functionality currently is not available when the provider is OpenSSL.

This property is read-only.

Data Type

Integer

SSLCertVersion Property (MQTT Component)

The certificate's version number.

Syntax

__property String SSLCertVersion = { read=FSSLCertVersion };

Default Value

""

Remarks

The certificate's version number. The possible values are the strings "V1", "V2", and "V3".

This property is read-only.

Data Type

String

SSLCertSubject Property (MQTT Component)

The subject of the certificate used for client authentication.

Syntax

__property String SSLCertSubject = { read=FSSLCertSubject, write=FSetSSLCertSubject };

Default Value

""

Remarks

The subject of the certificate used for client authentication.

This property must be set after all other certificate properties are set. When this property is set, a search is performed in the current certificate store to locate a certificate with a matching subject.

If a matching certificate is found, the property is set to the full subject of the matching certificate.

If an exact match is not found, the store is searched for subjects containing the value of the property.

If a match is still not found, the property is set to an empty string, and no certificate is selected.

The special value "*" picks a random certificate in the certificate store.

The certificate subject is a comma-separated list of distinguished name fields and values. For instance, "CN=www.server.com, OU=test, C=US, E=support@nsoftware.com". Common fields and their meanings are as follows:

If a field value contains a comma, it must be quoted.

Data Type

String

SSLCertEncoded Property (MQTT Component)

The certificate (PEM/Base64 encoded).

Syntax

__property String SSLCertEncoded = { read=FSSLCertEncoded, write=FSetSSLCertEncoded };
__property DynamicArray<Byte> SSLCertEncodedB = { read=FSSLCertEncodedB, write=FSetSSLCertEncodedB };

Default Value

""

Remarks

The certificate (PEM/Base64 encoded). This property is used to assign a specific certificate. The SSLCertStore and SSLCertSubject properties also may be used to specify a certificate.

When SSLCertEncoded is set, a search is initiated in the current SSLCertStore for the private key of the certificate. If the key is found, SSLCertSubject is updated to reflect the full subject of the selected certificate; otherwise, SSLCertSubject is set to an empty string.

This property is not available at design time.

Data Type

Byte Array

SSLEnabled Property (MQTT Component)

This property indicates whether Transport Layer Security/Secure Sockets Layer (TLS/SSL) is enabled.

Syntax

__property bool SSLEnabled = { read=FSSLEnabled, write=FSetSSLEnabled };

Default Value

False

Remarks

This property specifies whether TLS/SSL is enabled in the component. When False (default), the component operates in plaintext mode. When True, TLS/SSL is enabled.

TLS/SSL may also be enabled by setting SSLStartMode. Setting SSLStartMode will automatically update this property value.

This property is not available at design time.

Data Type

Boolean

SSLProvider Property (MQTT Component)

The Secure Sockets Layer/Transport Layer Security (SSL/TLS) implementation to use.

Syntax

__property TipqMQTTSSLProviders SSLProvider = { read=FSSLProvider, write=FSetSSLProvider };

enum TipqMQTTSSLProviders {
  sslpAutomatic=0,
  sslpPlatform=1,
  sslpInternal=2
};

Default Value

sslpAutomatic

Remarks

This property specifies the SSL/TLS implementation to use. In most cases the default value of 0 (Automatic) is recommended and should not be changed. When set to 0 (Automatic), the component will select whether to use the platform implementation or the internal implementation depending on the operating system as well as the TLS version being used.

Possible values are as follows:

In most cases using the default value (Automatic) is recommended. The component will select a provider depending on the current platform.

When Automatic is selected, the platform implementation is used by default. When TLS 1.3 is enabled via SSLEnabledProtocols, the internal implementation is used.

Data Type

Integer

SSLServerCertEffectiveDate Property (MQTT Component)

The date on which this certificate becomes valid.

Syntax

__property String SSLServerCertEffectiveDate = { read=FSSLServerCertEffectiveDate };

Default Value

""

Remarks

The date on which this certificate becomes valid. Before this date, it is not valid. The date is localized to the system's time zone. The following example illustrates the format of an encoded date:

23-Jan-2000 15:00:00.

This property is read-only.

Data Type

String

SSLServerCertExpirationDate Property (MQTT Component)

The date on which the certificate expires.

Syntax

__property String SSLServerCertExpirationDate = { read=FSSLServerCertExpirationDate };

Default Value

""

Remarks

The date on which the certificate expires. After this date, the certificate will no longer be valid. The date is localized to the system's time zone. The following example illustrates the format of an encoded date:

23-Jan-2001 15:00:00.

This property is read-only.

Data Type

String

SSLServerCertExtendedKeyUsage Property (MQTT Component)

A comma-delimited list of extended key usage identifiers.

Syntax

__property String SSLServerCertExtendedKeyUsage = { read=FSSLServerCertExtendedKeyUsage };

Default Value

""

Remarks

A comma-delimited list of extended key usage identifiers. These are the same as ASN.1 object identifiers (OIDs).

This property is read-only.

Data Type

String

SSLServerCertFingerprint Property (MQTT Component)

The hex-encoded, 16-byte MD5 fingerprint of the certificate.

Syntax

__property String SSLServerCertFingerprint = { read=FSSLServerCertFingerprint };

Default Value

""

Remarks

The hex-encoded, 16-byte MD5 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: bc:2a:72:af:fe:58:17:43:7a:5f:ba:5a:7c:90:f7:02

This property is read-only.

Data Type

String

SSLServerCertFingerprintSHA1 Property (MQTT Component)

The hex-encoded, 20-byte SHA-1 fingerprint of the certificate.

Syntax

__property String SSLServerCertFingerprintSHA1 = { read=FSSLServerCertFingerprintSHA1 };

Default Value

""

Remarks

The hex-encoded, 20-byte SHA-1 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 30:7b:fa:38:65:83:ff:da:b4:4e:07:3f:17:b8:a4:ed:80:be:ff:84

This property is read-only.

Data Type

String

SSLServerCertFingerprintSHA256 Property (MQTT Component)

The hex-encoded, 32-byte SHA-256 fingerprint of the certificate.

Syntax

__property String SSLServerCertFingerprintSHA256 = { read=FSSLServerCertFingerprintSHA256 };

Default Value

""

Remarks

The hex-encoded, 32-byte SHA-256 fingerprint of the certificate. This property is primarily used for keys which do not have a corresponding X.509 public certificate, such as PEM keys that only contain a private key. It is commonly used for SSH keys.

The following example illustrates the format: 6a:80:5c:33:a9:43:ea:b0:96:12:8a:64:96:30:ef:4a:8a:96:86:ce:f4:c7:be:10:24:8e:2b:60:9e:f3:59:53

This property is read-only.

Data Type

String

SSLServerCertIssuer Property (MQTT Component)

The issuer of the certificate.

Syntax

__property String SSLServerCertIssuer = { read=FSSLServerCertIssuer };

Default Value

""

Remarks

The issuer of the certificate. This property contains a string representation of the name of the issuing authority for the certificate.

This property is read-only.

Data Type

String

SSLServerCertPrivateKey Property (MQTT Component)

The private key of the certificate (if available).

Syntax

__property String SSLServerCertPrivateKey = { read=FSSLServerCertPrivateKey };

Default Value

""

Remarks

The private key of the certificate (if available). The key is provided as PEM/Base64-encoded data.

Note: The SSLServerCertPrivateKey may be available but not exportable. In this case, SSLServerCertPrivateKey returns an empty string.

This property is read-only.

Data Type

String

SSLServerCertPrivateKeyAvailable Property (MQTT Component)

Whether a PrivateKey is available for the selected certificate.

Syntax

__property bool SSLServerCertPrivateKeyAvailable = { read=FSSLServerCertPrivateKeyAvailable };

Default Value

false

Remarks

Whether a SSLServerCertPrivateKey is available for the selected certificate. If SSLServerCertPrivateKeyAvailable is True, the certificate may be used for authentication purposes (e.g., server authentication).

This property is read-only.

Data Type

Boolean

SSLServerCertPrivateKeyContainer Property (MQTT Component)

The name of the PrivateKey container for the certificate (if available).

Syntax

__property String SSLServerCertPrivateKeyContainer = { read=FSSLServerCertPrivateKeyContainer };

Default Value

""

Remarks

The name of the SSLServerCertPrivateKey container for the certificate (if available). This functionality is available only on Windows platforms.

This property is read-only.

Data Type

String

SSLServerCertPublicKey Property (MQTT Component)

The public key of the certificate.

Syntax

__property String SSLServerCertPublicKey = { read=FSSLServerCertPublicKey };

Default Value

""

Remarks

The public key of the certificate. The key is provided as PEM/Base64-encoded data.

This property is read-only.

Data Type

String

SSLServerCertPublicKeyAlgorithm Property (MQTT Component)

The textual description of the certificate's public key algorithm.

Syntax

__property String SSLServerCertPublicKeyAlgorithm = { read=FSSLServerCertPublicKeyAlgorithm };

Default Value

""

Remarks

The textual description of the certificate's public key algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_DH") or an object identifier (OID) string representing the algorithm.

This property is read-only.

Data Type

String

SSLServerCertPublicKeyLength Property (MQTT Component)

The length of the certificate's public key (in bits).

Syntax

__property int SSLServerCertPublicKeyLength = { read=FSSLServerCertPublicKeyLength };

Default Value

0

Remarks

The length of the certificate's public key (in bits). Common values are 512, 1024, and 2048.

This property is read-only.

Data Type

Integer

SSLServerCertSerialNumber Property (MQTT Component)

The serial number of the certificate encoded as a string.

Syntax

__property String SSLServerCertSerialNumber = { read=FSSLServerCertSerialNumber };

Default Value

""

Remarks

The serial number of the certificate encoded as a string. The number is encoded as a series of hexadecimal digits, with each pair representing a byte of the serial number.

This property is read-only.

Data Type

String

SSLServerCertSignatureAlgorithm Property (MQTT Component)

The text description of the certificate's signature algorithm.

Syntax

__property String SSLServerCertSignatureAlgorithm = { read=FSSLServerCertSignatureAlgorithm };

Default Value

""

Remarks

The text description of the certificate's signature algorithm. The property contains either the name of the algorithm (e.g., "RSA" or "RSA_MD5RSA") or an object identifier (OID) string representing the algorithm.

This property is read-only.

Data Type

String

SSLServerCertStore Property (MQTT Component)

The name of the certificate store for the client certificate.

Syntax

__property String SSLServerCertStore = { read=FSSLServerCertStore };
__property DynamicArray<Byte> SSLServerCertStoreB = { read=FSSLServerCertStoreB };

Default Value

"MY"

Remarks

The name of the certificate store for the client certificate.

The SSLServerCertStoreType property denotes the type of the certificate store specified by SSLServerCertStore. If the store is password-protected, specify the password in SSLServerCertStorePassword.

SSLServerCertStore is used in conjunction with the SSLServerCertSubject property to specify client certificates. If SSLServerCertStore has a value, and SSLServerCertSubject or SSLServerCertEncoded is set, a search for a certificate is initiated. Please see the SSLServerCertSubject property for details.

Designations of certificate stores are platform dependent.

The following designations are the most common User and Machine certificate stores in Windows:

When the certificate store type is cstPFXFile, this property must be set to the name of the file. When the type is cstPFXBlob, the property must be set to the binary contents of a PFX file (i.e., PKCS#12 certificate store).

This property is read-only.

Data Type

Byte Array

SSLServerCertStorePassword Property (MQTT Component)

If the type of certificate store requires a password, this property is used to specify the password needed to open the certificate store.

Syntax

__property String SSLServerCertStorePassword = { read=FSSLServerCertStorePassword };

Default Value

""

Remarks

If the type of certificate store requires a password, this property is used to specify the password needed to open the certificate store.

This property is read-only.

Data Type

String

SSLServerCertStoreType Property (MQTT Component)

The type of certificate store for this certificate.

Syntax

__property TipqMQTTSSLServerCertStoreTypes SSLServerCertStoreType = { read=FSSLServerCertStoreType };

enum TipqMQTTSSLServerCertStoreTypes {
  cstUser=0,
  cstMachine=1,
  cstPFXFile=2,
  cstPFXBlob=3,
  cstJKSFile=4,
  cstJKSBlob=5,
  cstPEMKeyFile=6,
  cstPEMKeyBlob=7,
  cstPublicKeyFile=8,
  cstPublicKeyBlob=9,
  cstSSHPublicKeyBlob=10,
  cstP7BFile=11,
  cstP7BBlob=12,
  cstSSHPublicKeyFile=13,
  cstPPKFile=14,
  cstPPKBlob=15,
  cstXMLFile=16,
  cstXMLBlob=17,
  cstJWKFile=18,
  cstJWKBlob=19,
  cstSecurityKey=20,
  cstBCFKSFile=21,
  cstBCFKSBlob=22,
  cstPKCS11=23,
  cstAuto=99
};

Default Value

cstUser

Remarks

The type of certificate store for this certificate.

The component supports both public and private keys in a variety of formats. When the cstAuto value is used, the component will automatically determine the type. This property can take one of the following values:

This property is read-only.

Data Type

Integer

SSLServerCertSubjectAltNames Property (MQTT Component)

Comma-separated lists of alternative subject names for the certificate.

Syntax

__property String SSLServerCertSubjectAltNames = { read=FSSLServerCertSubjectAltNames };

Default Value

""

Remarks

Comma-separated lists of alternative subject names for the certificate.

This property is read-only.

Data Type

String

SSLServerCertThumbprintMD5 Property (MQTT Component)

The MD5 hash of the certificate.

Syntax

__property String SSLServerCertThumbprintMD5 = { read=FSSLServerCertThumbprintMD5 };

Default Value

""

Remarks

The MD5 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLServerCertThumbprintSHA1 Property (MQTT Component)

The SHA-1 hash of the certificate.

Syntax

__property String SSLServerCertThumbprintSHA1 = { read=FSSLServerCertThumbprintSHA1 };

Default Value

""

Remarks

The SHA-1 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLServerCertThumbprintSHA256 Property (MQTT Component)

The SHA-256 hash of the certificate.

Syntax

__property String SSLServerCertThumbprintSHA256 = { read=FSSLServerCertThumbprintSHA256 };

Default Value

""

Remarks

The SHA-256 hash of the certificate. It is primarily used for X.509 certificates. If the hash does not already exist, it is automatically computed.

This property is read-only.

Data Type

String

SSLServerCertUsage Property (MQTT Component)

The text description of UsageFlags .

Syntax

__property String SSLServerCertUsage = { read=FSSLServerCertUsage };

Default Value

""

Remarks

The text description of SSLServerCertUsageFlags.

This value will be one or more of the following strings and will be separated by commas:

• Digital Signature
• Non-Repudiation
• Key Encipherment
• Data Encipherment
• Key Agreement
• Certificate Signing
• CRL Signing
• Encipher Only

If the provider is OpenSSL, the value is a comma-separated list of X.509 certificate extension names.

This property is read-only.

Data Type

String

SSLServerCertUsageFlags Property (MQTT Component)

The flags that show intended use for the certificate.

Syntax

__property int SSLServerCertUsageFlags = { read=FSSLServerCertUsageFlags };

Default Value

0

Remarks

The flags that show intended use for the certificate. The value of SSLServerCertUsageFlags is a combination of the following flags:

Please see the SSLServerCertUsage property for a text representation of SSLServerCertUsageFlags.

This functionality currently is not available when the provider is OpenSSL.

This property is read-only.

Data Type

Integer

SSLServerCertVersion Property (MQTT Component)

The certificate's version number.

Syntax

__property String SSLServerCertVersion = { read=FSSLServerCertVersion };

Default Value

""

Remarks

The certificate's version number. The possible values are the strings "V1", "V2", and "V3".

This property is read-only.

Data Type

String

SSLServerCertSubject Property (MQTT Component)

The subject of the certificate used for client authentication.

Syntax

__property String SSLServerCertSubject = { read=FSSLServerCertSubject };

Default Value

""

Remarks

The subject of the certificate used for client authentication.

This property must be set after all other certificate properties are set. When this property is set, a search is performed in the current certificate store to locate a certificate with a matching subject.

If a matching certificate is found, the property is set to the full subject of the matching certificate.

If an exact match is not found, the store is searched for subjects containing the value of the property.

If a match is still not found, the property is set to an empty string, and no certificate is selected.

The special value "*" picks a random certificate in the certificate store.

The certificate subject is a comma-separated list of distinguished name fields and values. For instance, "CN=www.server.com, OU=test, C=US, E=support@nsoftware.com". Common fields and their meanings are as follows:

If a field value contains a comma, it must be quoted.

This property is read-only.

Data Type

String

SSLServerCertEncoded Property (MQTT Component)

The certificate (PEM/Base64 encoded).

Syntax

__property String SSLServerCertEncoded = { read=FSSLServerCertEncoded };
__property DynamicArray<Byte> SSLServerCertEncodedB = { read=FSSLServerCertEncodedB };

Default Value

""

Remarks

The certificate (PEM/Base64 encoded). This property is used to assign a specific certificate. The SSLServerCertStore and SSLServerCertSubject properties also may be used to specify a certificate.

When SSLServerCertEncoded is set, a search is initiated in the current SSLServerCertStore for the private key of the certificate. If the key is found, SSLServerCertSubject is updated to reflect the full subject of the selected certificate; otherwise, SSLServerCertSubject is set to an empty string.

This property is read-only and not available at design time.

Data Type

Byte Array

Timeout Property (MQTT Component)

This property includes the timeout for the component.

Syntax

__property int Timeout = { read=FTimeout, write=FSetTimeout };

Default Value

60

Remarks

If the Timeout property is set to 0, all operations return immediately, potentially failing with a WOULDBLOCK error if data cannot be sent immediately.

If Timeout is set to a positive value, data is sent in a blocking manner and the component will wait for the operation to complete before returning control. The component will handle any potential WOULDBLOCK errors internally and automatically retry the operation for a maximum of Timeout seconds.

The component will use DoEvents to enter an efficient wait loop during any potential waiting period, making sure that all system events are processed immediately as they arrive. This ensures that the host application does not freeze and remains responsive.

If Timeout expires, and the operation is not yet complete, the component raises an exception.

Note: By default, all timeouts are inactivity timeouts, that is, the timeout period is extended by Timeout seconds when any amount of data is successfully sent or received.

The default value for the Timeout property is 60 seconds.

Data Type

Integer

User Property (MQTT Component)

A username if authentication is to be used.

Syntax

__property String User = { read=FUser, write=FSetUser };

Default Value

""

Remarks

This property can be set to a username if authentication is to be used.

In MQTT 3.1.1, while a User may be specified without a Password, setting a Password without a User is not supported; attempting to do so will cause the server to reject the connection attempt.

In MQTT 5, a Password may be set without a User, allowing the field to be used for credentials other than a password.

This property is not available at design time.

Data Type

String

Version Property (MQTT Component)

The MQTT protocol version that the component will conform to.

Syntax

__property TipqMQTTVersions Version = { read=FVersion, write=FSetVersion };

enum TipqMQTTVersions {
  mvV3=0,
  mvV5=1
};

Default Value

mvV3

Remarks

This property specifies the version of the MQTT protocol to use. Possible values are:

This property is not available at design time.

Data Type

Integer

WillMessage Property (MQTT Component)

The message that the server should publish in the event of an ungraceful disconnection.

Syntax

__property String WillMessage = { read=FWillMessage, write=FSetWillMessage };

Default Value

""

Remarks

This property may be set before calling Connect to specify to the server a message that should be published on WillTopic if the connection is closed ungracefully. Since it is sent to the server when Connect is called, this property's value cannot be changed when already connected.

Note that the WillMessage will only be sent to the server when Connect is called if WillTopic is set.

Refer to WillTopic for more information about MQTT Will functionality.

This property is not available at design time.

Data Type

String

WillTopic Property (MQTT Component)

The topic that the server should publish the WillMessage to in the event of an ungraceful disconnection.

Syntax

__property String WillTopic = { read=FWillTopic, write=FSetWillTopic };

Default Value

""

Remarks

This property may be set before calling Connect to specify the topic name that the server should publish the WillMessage on if the connection is closed ungracefully. Since it is sent to the server when Connect is called, this property's value cannot be changed when already connected.

MQTT Wills

The Will feature of MQTT allows a client to specify to the server a WillMessage to publish (as well as a WillTopic to publish it on) in the event of an ungraceful disconnection.

An "ungraceful disconnection" is any disconnection other than one triggered by calling Disconnect (in which case the server discards the Will message without publishing it). Note that in MQTT 5, the client can set a DisconnectReasonCode of 0x04 before calling Disconnect to instruct the server to publish the Will message anyway.

In addition to the WillTopic and WillMessage properties, the WillQOS setting may be used to specify the Will message's QoS level, and the WillRetain setting to set the Will message's Retain flag. Refer to those settings for more information.

If WillTopic is set to empty string (default) when Connect is called, the component will not send a Will to the server.

In MQTT 5, the "WillDelayInterval" value in the WillProperties config can specify a delay between the ending of the connection and sending the will message, so that the WillMessage will not be sent if a connection is re-established within a certain period of time.

This property is not available at design time.

Data Type

String

Config Method (MQTT Component)

Sets or retrieves a configuration setting.

Syntax

String __fastcall Config(String ConfigurationString);

Remarks

Config is a generic method available in every component. It is used to set and retrieve configuration settings for the component.

These settings are similar in functionality to properties, but they are rarely used. In order to avoid "polluting" the property namespace of the component, access to these internal properties is provided through the Config method.

To set a configuration setting named PROPERTY, you must call Config("PROPERTY=VALUE"), where VALUE is the value of the setting expressed as a string. For boolean values, use the strings "True", "False", "0", "1", "Yes", or "No" (case does not matter).

To read (query) the value of a configuration setting, you must call Config("PROPERTY"). The value will be returned as a string.

Connect Method (MQTT Component)

Connects to the remote host.

Syntax

void __fastcall Connect();

Remarks

This method connects to the remote host specified by RemoteHost and RemotePort. Calling this method is equivalent to setting the Connected property to True.

By default the component will connect in plaintext. To enable SSL set SSLEnabled to True.

In addition, WebSocket connections are supported. To connect using WebSockets specify a hostname beginning with ws:// (plaintext) or wss:// (SSL). For instance, ws://test.mosquitto.org.

When connecting to an MQTT server, the component sends the following information:

• The values of the ClientId, CleanSession, and KeepAliveInterval properties.
• The value of the User property (if non-empty).
• The value of the Password property (if non-empty).
• The values of the WillTopic and WillMessage properties and the WillQOS and WillRetain configuration settings.
• MQTT 5 specific values from ClientTopicAliasMax, SessionExpInterval, ConnectProperties and WillProperties.

If CleanSession is True, check the SessionPresent configuration setting once connected to determine whether the server actually had any session state saved.

Refer to CleanSession, SaveSession, and RestoreSession for more information about MQTT sessions and session state persistence; refer to WillTopic, WillMessage, WillQOS, and WillRetain for more information about MQTT Wills.

Basic Connection Example mqtt1.ClientId = "testClient"; mqtt1.CleanSession = true; mqtt1.KeepAliveInterval = 30; mqtt1.WillTopic = "wills/" + mqtt1.ClientId; mqtt1.WillMessage = mqtt1.ClientId + " was disconnected ungracefully!"; mqtt1.RemoteHost = "mqtt.test-server.com"; mqtt1.RemotePort = 1883; mqtt1.Connect();

ConnectTo Method (MQTT Component)

Connects to the remote host.

Syntax

void __fastcall ConnectTo(String Host, int Port);

Remarks

This method connects to the remote host specified by the Host and Port parameters. Calling this method is equivalent to setting the RemoteHost property to Host, setting RemotePort to Port, and then setting the Connected property to True.

By default the component will connect in plaintext. To enable SSL set SSLEnabled to True.

In addition, WebSocket connections are supported. To connect using WebSockets specify a hostname beginning with ws:// (plaintext) or wss:// (SSL). For instance, ws://test.mosquitto.org.

When connecting to an MQTT server, the component sends the following information:

• The values of the ClientId, CleanSession, and KeepAliveInterval properties.
• The value of the User property (if non-empty).
• The value of the Password property (if non-empty).
• The values of the WillTopic and WillMessage properties and the WillQOS and WillRetain configuration settings.
• MQTT 5 specific values from ClientTopicAliasMax, SessionExpInterval, ConnectProperties and WillProperties.

If CleanSession is True, check the SessionPresent configuration setting once connected to determine whether the server actually had any session state saved.

Refer to CleanSession, SaveSession, and RestoreSession for more information about MQTT sessions and session state persistence; refer to WillTopic, WillMessage, WillQOS, and WillRetain for more information about MQTT Wills.

Basic Connection Example mqtt1.ClientId = "testClient"; mqtt1.CleanSession = true; mqtt1.KeepAliveInterval = 30; mqtt1.WillTopic = "wills/" + mqtt1.ClientId; mqtt1.WillMessage = mqtt1.ClientId + " was disconnected ungracefully!"; mqtt1.ConnectTo("mqtt.test-server.com", 1883);

Disconnect Method (MQTT Component)

This method disconnects from the remote host.

Syntax

void __fastcall Disconnect();

Remarks

This method disconnects from the remote host. Calling this method is equivalent to setting the Connected property to False.

Refer to the Connected property for more information about MQTT-specific behavior.

DoEvents Method (MQTT Component)

This method processes events from the internal message queue.

Syntax

void __fastcall DoEvents();

Remarks

When DoEvents is called, the component processes any available events. If no events are available, it waits for a preset period of time, and then returns.

Interrupt Method (MQTT Component)

Interrupt the current action and disconnects from the remote host.

Syntax

void __fastcall Interrupt();

Remarks

This method will interrupt the current method (if applicable) and cause the component to disconnect from the remote host.

PublishData Method (MQTT Component)

Publishes a message with a raw data payload.

Syntax

void __fastcall PublishData(String Topic, int QOS, DynamicArray<Byte> Data);

Remarks

This method publishes an MQTT message with a raw data payload to the specified Topic at a given QOS level.

Publish Examples // Publish a simple string-based message. mqtt1.PublishMessage("/home/floor1/security/camera2", 1, "Cat detected!"); // Publish a raw data message. byte[] catPicture = ...; mqtt1.PublishData("/home/floor1/security/camera2", 1, catPicture);

The Retain configuration setting may be set before calling this method in order to publish a retained message (see Retain for more information).

Topic Names

Topic names are case-sensitive, must be 1-65535 characters long, and may include any characters except wildcard characters (# and +) and the null character. The / character separates levels within a topic name, which is important in the context of subscribing (see Subscribe for more information).

Keep in mind that using topic names with leading or trailing / characters will cause topic levels with zero-length names to be created. That is, a topic name like /a/b/ consists of the levels '', 'a', 'b', and ''. Depending on the server, multiple successive /s may also cause zero-length levels to be created, or may be treated as a single /.

Topic names that begin with a $ are "system topics", and servers will typically prevent clients from publishing to them.

For example, topic names that begin with $share are reserved for Shared Subscriptions (see Subscribe).

QoS Values

QoS values set the service level for delivery of a message. Values range from 0 to 2 and have the following meanings:

QoS is not guaranteed to be end-to-end in MQTT. The server must downgrade a message's QoS level when delivering it to clients who specified a lower "maximum acceptable" QoS when they subscribed. For example, if Client X subscribes to a topic at QoS 1, and Client Y publishes a message to that topic at QoS 2, the server will downgrade the message to QoS 1 when attempting to deliver it to Client X.

Outbound Message Processing

Outgoing messages with a QoS of 1 follow these steps:

1. The component sends the PUBLISH packet, then adds the message to OutgoingMessages.
2. The component waits to receive a PUBACK (publish acknowledgment) packet.
3. The MessageAck event is fired.
4. The message is removed from OutgoingMessages.
5. The MessageOut event is fired.

Outgoing messages with a QoS of 2 follow these steps:

1. The component sends the PUBLISH packet, then adds the message to OutgoingMessages.
2. The component waits to receive a PUBREC (publish received) packet.
3. The component sends a PUBREL (publish release) packet in response.
4. The component waits to receive a PUBCOMP (publish complete) packet.
5. The MessageAck event is fired.
6. The message is removed from OutgoingMessages.
7. The MessageOut event is fired.

In MQTT 3.1.1, the RepublishInterval configuration setting, if set to a non-zero value (default), controls how long the component will wait to receive a PUBACK (for QoS 1) or PUBREC (for QoS 2) before automatically republishing an outgoing message. In MQTT 5, messages are only republished if the client is disconnected before receiving a PUBACK or PUBREC.

MQTT 5 Notes

MQTT 5 makes a number of new features available when publishing messages, including:

• TopicAlias - Set an integer alias along with the topic name when first publishing a message. When publishing additional messages to the same topic if TopicAlias is set the Topic parameter does not need to be set. This reduces the size of the message sent to the server.
• Request / Response - Set a ResponseTopic which identifies the topic to which a receiver should respond.

Some of these features require configuration settings to be set prior to publishing. In these cases, note that these configuration settings will continue to be applicable to any future PUBLISH packets sent with the method unless they are updated or reset. To prevent clear a previously set configuration setting, set it to "", or -1 (for integers).

See the OutgoingMessageProperties configuration setting for additional details.

PublishMessage Method (MQTT Component)

Publishes a message with a string payload.

Syntax

void __fastcall PublishMessage(String Topic, int QOS, String Message);

Remarks

This method publishes an MQTT message with a string payload to the specified Topic at a given QOS level.

Publish Examples // Publish a simple string-based message. mqtt1.PublishMessage("/home/floor1/security/camera2", 1, "Cat detected!"); // Publish a raw data message. byte[] catPicture = ...; mqtt1.PublishData("/home/floor1/security/camera2", 1, catPicture);

The Retain configuration setting may be set before calling this method in order to publish a retained message (see Retain for more information).

Topic Names

Topic names are case-sensitive, must be 1-65535 characters long, and may include any characters except wildcard characters (# and +) and the null character. The / character separates levels within a topic name, which is important in the context of subscribing (see Subscribe for more information).

Keep in mind that using topic names with leading or trailing / characters will cause topic levels with zero-length names to be created. That is, a topic name like /a/b/ consists of the levels '', 'a', 'b', and ''. Depending on the server, multiple successive /s may also cause zero-length levels to be created, or may be treated as a single /.

Topic names that begin with a $ are "system topics", and servers will typically prevent clients from publishing to them.

For example, topic names that begin with $share are reserved for Shared Subscriptions (see Subscribe).

QoS Values

QoS values set the service level for delivery of a message. Values range from 0 to 2 and have the following meanings:

QoS is not guaranteed to be end-to-end in MQTT. The server must downgrade a message's QoS level when delivering it to clients who specified a lower "maximum acceptable" QoS when they subscribed. For example, if Client X subscribes to a topic at QoS 1, and Client Y publishes a message to that topic at QoS 2, the server will downgrade the message to QoS 1 when attempting to deliver it to Client X.

Outbound Message Processing

Outgoing messages with a QoS of 1 follow these steps:

1. The component sends the PUBLISH packet, then adds the message to OutgoingMessages.
2. The component waits to receive a PUBACK (publish acknowledgment) packet.
3. The MessageAck event is fired.
4. The message is removed from OutgoingMessages.
5. The MessageOut event is fired.

Outgoing messages with a QoS of 2 follow these steps:

1. The component sends the PUBLISH packet, then adds the message to OutgoingMessages.
2. The component waits to receive a PUBREC (publish received) packet.
3. The component sends a PUBREL (publish release) packet in response.
4. The component waits to receive a PUBCOMP (publish complete) packet.
5. The MessageAck event is fired.
6. The message is removed from OutgoingMessages.
7. The MessageOut event is fired.

In MQTT 3.1.1, the RepublishInterval configuration setting, if set to a non-zero value (default), controls how long the component will wait to receive a PUBACK (for QoS 1) or PUBREC (for QoS 2) before automatically republishing an outgoing message. In MQTT 5, messages are only republished if the client is disconnected before receiving a PUBACK or PUBREC.

MQTT 5 Notes

MQTT 5 makes a number of new features available when publishing messages, including:

• TopicAlias - Set an integer alias along with the topic name when first publishing a message. When publishing additional messages to the same topic if TopicAlias is set the Topic parameter does not need to be set. This reduces the size of the message sent to the server.
• Request / Response - Set a ResponseTopic which identifies the topic to which a receiver should respond.

Some of these features require configuration settings to be set prior to publishing. In these cases, note that these configuration settings will continue to be applicable to any future PUBLISH packets sent with the method unless they are updated or reset. To prevent clear a previously set configuration setting, set it to "", or -1 (for integers).

See the OutgoingMessageProperties configuration setting for additional details.

Reset Method (MQTT Component)

This method will reset the component.

Syntax

void __fastcall Reset();

Remarks

This method will reset the component's properties to their default values.

RestoreSession Method (MQTT Component)

Restores session state data.

Syntax

void __fastcall RestoreSession(String StateData);

Remarks

This method restores previously-saved session state data and sets CleanSession to False. If the SessionStateFile configuration setting is set, the component will use the contents of that file to restore the session state data, ignoring the string passed to this method.

Depending on the elapsed time between connections the server may discard any previously saved session data on its side.

In MQTT 3.1.1, the time after which the server discards saved session data is not defined in the protocol specification and may vary between implementations. As a result, when re-connecting it may not be known if the server is capable of restoring a previous session.

To determine if a session can be restored on connection, set CleanSession to False, ClientId to the same value used in the initial connection, and call ConnectTo.

When the Connected event fires, query the SessionPresent configuration setting. If SessionPresent is True the session should be restored by calling RestoreSession. If SessionPresent is False the session should not be restored so that the connection proceeds as a clean session.

Note: Not all servers support the use of SessionPresent.

Restore Session Example (Query SessionPresent) mqtt1.CleanSession = false; mqtt1.ClientId = clientId; mqtt1.OnConnected += (s, e) => { if (mqtt1.Config("SessionPresent").ToLower() == "true") mqtt1.RestoreSession(sessionStr); }; mqtt1.ConnectTo(host,port);

If it is known that the server has not discarded the session state, for instance from familiarity with the server implementation and its behavior, then a simplified procedure can be performed. Simply set ClientId to the value used in the initial connection, call RestoreSession, and then call ConnectTo.

Restore Session Example (Server Status Known) mqtt1.ClientId = clientId; mqtt1.RestoreSession(sessionStr); mqtt1.ConnectTo(host,port);

Refer to CleanSession and SaveSession for more information.

MQTT 5 Notes

In MQTT 5, the time after which the server discards saved session data is controlled by the SessionExpInterval. The server is required to store state data for the amount of time specified by this value, at which point it is required to delete it.

This feature allows the client to use its own time-based logic to determine whether it is necessary to call RestoreSession.

SaveSession Method (MQTT Component)

Saves session state data.

Syntax

String __fastcall SaveSession();

Remarks

This method saves session state data currently held by the component, returning it as a string that can later be used to restore it. If the SessionStateFile configuration setting is set, the component will also write the session state data to that file (creating and/or overwriting it, as necessary).

Refer to CleanSession and RestoreSession for more information.

Subscribe Method (MQTT Component)

Subscribes the component to one or more topic filters.

Syntax

void __fastcall Subscribe(String TopicFilter, int QOS);

Remarks

This method subscribes the component to one or more topic filters using one or more QoS levels.

The Subscribed event will fire once for each topic filter given once the server acknowledges the subscription request(s). Keep in mind that the server is allowed to start publishing messages before it sends the acknowledgment.

It is legal to call Subscribe again for the same topic filter at any time, and pass a different QoS value at that time if desired. The Subscribed event will fire as normal when doing this.

Subscribe Examples // Subscribed event handler. mqtt1.OnSubscribed += (s, e) => { if (e.ResponseCode <= 2) Console.WriteLine("Subscribed to " + e.TopicFilter + " at QoS " + e.QOS + "."); else Console.WriteLine("Failed to subscribe to " + e.TopicFilter + "."); }; // Basic, subscribe to some topic filters, all at the same QoS level. mqtt1.Subscribe("home,home/floor1/+/temperature,home/floor2/#", 2); // A bit more advanced, subscribe to the same topic filters, but at different QoS levels. mqtt1.Config("TopicQOSArray=1,2,2"); // The 0 is ignored here since we've specified individual QoS values explicitly. mqtt1.Subscribe("home,home/floor1/+/temperature,home/floor2/#", 0);

Topic Filters

The string passed for TopicFilter must contain one or more valid topic filter strings, separated by the delimiter string specified by the TopicDelimiter configuration setting (, by default).

A topic filter is a case-sensitive string between 1 and 65535 characters long (per topic filter), and can include any character other than the null character. Certain characters have special meanings:

• / - The topic level separator
• # - The multi-level wildcard (zero or more levels)
• + - The single-level wildcard (exactly one level)
• Leading $ - Denotes a "system topic"

Note that both types of wildcards may be used in the same topic filter.

Topic Level Separators

The topic level separator, as its name implies, is used to separate a topic name (or in this case, filter) into "levels". This concept of topic names having levels is what allows topic filters to match multiple topics through the use of wildcards. For the examples in the next sections, assume the following topics exist:

• home/floor1
• home/floor1/livingRoom
• home/floor1/livingRoom/temperature
• home/floor1/kitchen/temperature
• home/floor1/kitchen/fridge/temperature
• home/floor2/bedroom1
• home/floor2/bedroom1/temperature

Multi-level Wildcards

The multi-level wildcard character is used at the end of a topic filter to make it match an arbitrary number of successive levels. For example, the topic filter home/floor1/# would match the following topics:

• home/floor1 (because it can match zero levels)
• home/floor1/livingRoom
• home/floor1/livingRoom/temperature
• home/floor1/kitchen/temperature
• home/floor1/kitchen/fridge/temperature

Here are some things to keep in mind when using a multi-level wildcard:

• # must always be the last character in the topic filter (e.g., home/floor1/#/livingRoom is not valid)
• # must always be preceded by a / (e.g., home/floor1# is not valid)
• # by itself is a valid topic filter, and will match all topics except system topics

Single-level Wildcards

The single-level wildcard character is used between two /s in a topic filter to make it any single level. For example, the topic filter home/floor1/+/temperature would match the following topics:

• home/floor1/livingRoom/temperature
• home/floor1/kitchen/temperature

Any number of single-level wildcards are supported in a topic filter. For example, the topic filter home/+/+/temperature would match the following topics:

• home/floor1/livingRoom/temperature
• home/floor1/kitchen/temperature
• home/floor2/bedroom1/temperature

Here are some things to keep in mind when using single-level wildcards:

• + must always be separated from other levels using /s (e.g., home/floor1+ is invalid, but +/floor1/+ is valid)
• + by itself is a valid topic filter, and will match all topics with exactly one level in their name except system topics
• Remember, topic names with a leading / have a zero-length string as their first level. So a topic named /people would be matched by the topic filter +/+, but not by +
• + must match exactly one level. So for example, the topic filter home/floor1/kitchen/+/temperature would match /home/floor1/kitchen/fridge/temperature, but not home/floor1/kitchen/temperature

System Topics

Topic names which begin with a $ are "system topics". Typically, the server prohibits clients from publishing to such topics, but permits subscribing to them. As described above, wildcards will never match the first level of a topic if it begins with a $.

Note that MQTT 5 defines shared subscriptions, a special type of system topic. See the MQTT 5 notes below for more.

Requested QoS Values

The QoS value passed for QOS will be used to subscribe to all given topic filters, unless the TopicQOSArray configuration setting is used to specify explicit QoS values for each individual topic filter.

QoS values range from 0 to 2 and have the following meanings:

QoS is not guaranteed to be end-to-end in MQTT. The server must downgrade a message's QoS level when delivering it to clients who specified a lower "maximum acceptable" QoS when they subscribed. For example, if Client X subscribes to a topic at QoS 1, and Client Y publishes a message to that topic at QoS 2, the server will downgrade the message to QoS 1 when attempting to deliver it to Client X.

MQTT 5 Notes

MQTT 5 defines several new features that apply to subscriptions, including Shared Subscriptions, Subscription Options and Subscription Identifiers. Some of these features require configuration settings to be set prior to calling Subscribe. In these cases, note that thee configuration settings will continue to be applied to any future SUBSCRIBE packets sent with the method unless they are updated or reset. To prevent a value from being included in packets after it has been set previously, set it to "", or -1 (for integers).

Shared Subscriptions

Shared subscriptions allow a client to subscribe to a topic as a part of a group of clients, where each client in the group is subscribing to the same topic. Each message published to such a group will be delivered to only one client in the group, making shared subscriptions useful when several clients share the processing of the publications in parallel.

Subscribing to a topic as part of a shared subscription is similar to a normal subscription, the only difference being the syntax of the topic filter passed to the Subscribe method.

The format of this filter is $share/{ShareName}/{filter}, where

• $share is a string literal identifying the subscription as a shared subscriptions.
• {ShareName} is a string at least one character long that must not include /, + or #.
• {filter} is a full topic filter formatted just as in a non-shared subscription.

Unsubscribing is done by passing the same value to the Unsubscribe method.

A shared subscription behaves the same way as a non-shared subscription, except that the $share/{ShareName} portion of the topic filter is ignored when filtering publication topics, and that the server will distribute delivery of messages amongst the group, with each message delivered to only one client per group per topic.

Shared subscriptions can be implemented without any additional properties or methods, simply by using the Subscribe and Unsubscribe methods. However, if it is necessary to verify that the feature is supported by the server, check the "SharedSubscriptionAvailable" value of the ConnAckProperties config.

Shared Subscription Example mqtt1.Subscribe("$share/myShareGroup/myTopicFilter/subTopic", 2);

Subscription Options

MQTT 5 defines three subscription options which can be configured on a per-subscription basis and are useful for message bridge applications:

• No Local flag - indicates that messages must not be forwarded to a connection with a ClientId equal to the ClientId of the publishing connection (cannot be set on a shared subscription).
• Retain As Published flag - indicates that messages forwarded using this subscription keep the retain flag they were published with (as opposed to always being set to False).
• Retain Handling option - specifies whether retained messages are sent when the subscription is established. Possible values are:

  0	Send retained messages at the time of the subscribe
  1	Send retained messages at subscribe only if the subscription does not currently exist
  2	Do not send retained messages at the time of the subscribe

To specify these options in the subscribe method, the component has three corresponding configuration settings (TopicNLArray, TopicRAPArray and TopicRHArray) which each take a string value in the form of a comma-separated list. Each element in the list corresponds to a topic filter passed to the Subscribe method, as with TopicQOSArray.

If the subscription is only for one topic, these lists would have only one value. If the number of elements in the string is less than the number of topic filters in the subscription, the final element will be applied to all remaining topics.

Subscription Options Example mqtt1.Connected = true; mqtt1.Config("TopicNLArray=true, false, true"); // TestTopic1 = true, TestTopic2 = false, TestTopic3 = true mqtt1.Config("TopicRAPArray=false"); // TestTopic1 = false, TestTopic2 = false, TestTopic3 = false mqtt1.Config("TopicRHArray=1, 0"); // // TestTopic1 = 1, TestTopic2 = 0, TestTopic3 = 0 mqtt1.Subscribe("TestTopic1, TestTopic2, TestTopic3", 1);

Subscription Identifiers

MQTT 5 allows clients to specify a numeric subscription identifier which will be returned with messages delivered for that subscription.

To do so with the component, set the SubscriptionIdentifier configuration setting before calling Subscribe. To update the identifier, call Subscribe with a new SubscriptionIdentifier.

To verify that a server supports subscription identifiers, check the "SubscriptionIdentifiersAvailable" value in the ConnAckProperties configuration setting. See the SubscriptionIdentifiers property of the MQTTMessage type for details on returning the ids associated with messages.

Note that a topic may have multiple identifiers associated with it (due to wildcards), and the same identifier may be associated with multiple topics.

Subscription Options Example mqtt1.Connected = true; mqtt1.OnMessageAck += (o, e) => { String ids = mqtt1.IncomingMessages[e.Index].SubscriptionIdentifiers; // ids = "123,321" }; mqtt1.Config("SubscriptionIdentifier=123"); mqtt1.Subscribe("test_topic/subtopic", 1); mqtt1.Config("SubscriptionIdentifier=321"); mqtt1.Subscribe("test_topic/+", 1); mqtt2.Connected = true; mqtt2.PublishMessage("test_topic/subtopic", 1, "hello world");

Unsubscribe Method (MQTT Component)

Unsubscribes the component from one or more topic filters.

Syntax

void __fastcall Unsubscribe(String TopicFilter);

Remarks

This method unsubscribes the component from one or more topic filters. The string passed for TopicFilter must contain one or more valid topic filter strings, separated by the delimiter string specified by the TopicDelimiter configuration setting (, by default).

The Unsubscribed event will fire when the server has acknowledged the unsubscribe request. However, note that the server's acknowledgment doesn't specify which topics a client was unsubscribed from. Please refer to the Unsubscribed event for more information.

To successfully unsubscribe from a topic filter, the exact filter must be passed to Unsubscribe, regardless of whether or not if contains wildcards. The server ignores any topic filters in an unsubscribe request which do not exactly match that of an existing subscription.

It is impossible to partially unsubscribe from a topic filter with wildcards (that is, if a client is subscribed to a topic filter home/floor1/+/#, requesting to unsubscribe from a topic filter home/floor1/livingRoom/temperature does nothing).

Similarly, because topic filters in an unsubscribe request are simply compared character-by-character with existing subscriptions rather than being interpreted, it is not possible to perform an action such as unsubscribing from all currently subscribed topics by passing "#" for TopicFilter.

Unsubscribe Example // Unsubscribe from topic filters; have to use the exact same strings as before. If this // was to be called after calling the code example shown for the Subscribe() method, we // would still be subscribed to the "home" topic filter. mqtt1.Unsubscribe("home/floor1/+/temperature,home/floor2/#");

Connected Event (MQTT Component)

Fired immediately after a connection completes (or fails).

Syntax

typedef struct {
  int StatusCode;
  String Description;
} TipqMQTTConnectedEventParams;
typedef void __fastcall (__closure *TipqMQTTConnectedEvent)(System::TObject* Sender, TipqMQTTConnectedEventParams *e);
__property TipqMQTTConnectedEvent OnConnected = { read=FOnConnected, write=FOnConnected };

Remarks

If the connection is made normally, StatusCode is 0 and Description is "OK".

If the connection fails, StatusCode has the error code returned by the Transmission Control Protocol (TCP)/IP stack. Description contains a description of this code. The value of StatusCode is equal to the value of the error.

Please refer to the Error Codes section for more information.

ConnectionStatus Event (MQTT Component)

Fired to indicate changes in the connection state.

Syntax

typedef struct {
  String ConnectionEvent;
  int StatusCode;
  String Description;
} TipqMQTTConnectionStatusEventParams;
typedef void __fastcall (__closure *TipqMQTTConnectionStatusEvent)(System::TObject* Sender, TipqMQTTConnectionStatusEventParams *e);
__property TipqMQTTConnectionStatusEvent OnConnectionStatus = { read=FOnConnectionStatus, write=FOnConnectionStatus };

Remarks

This event is fired when the connection state changes: for example, completion of a firewall or proxy connection or completion of a security handshake.

The ConnectionEvent parameter indicates the type of connection event. Values may include the following:

Disconnected Event (MQTT Component)

Fired when a connection is closed.

Syntax

typedef struct {
  int StatusCode;
  String Description;
} TipqMQTTDisconnectedEventParams;
typedef void __fastcall (__closure *TipqMQTTDisconnectedEvent)(System::TObject* Sender, TipqMQTTDisconnectedEventParams *e);
__property TipqMQTTDisconnectedEvent OnDisconnected = { read=FOnDisconnected, write=FOnDisconnected };

Remarks

If the connection is broken normally, StatusCode is 0 and Description is "OK".

If the connection is broken for any other reason, StatusCode has the error code returned by the Transmission Control Protocol (TCP/IP) subsystem. Description contains a description of this code. The value of StatusCode is equal to the value of the TCP/IP error.

Please refer to the Error Codes section for more information.

Error Event (MQTT Component)

Fired when information is available about errors during data delivery.

Syntax

typedef struct {
  int ErrorCode;
  String Description;
} TipqMQTTErrorEventParams;
typedef void __fastcall (__closure *TipqMQTTErrorEvent)(System::TObject* Sender, TipqMQTTErrorEventParams *e);
__property TipqMQTTErrorEvent OnError = { read=FOnError, write=FOnError };

Remarks

The Error event is fired in case of exceptional conditions during message processing. Normally the component raises an exception.

The ErrorCode parameter contains an error code, and the Description parameter contains a textual description of the error. For a list of valid error codes and their descriptions, please refer to the Error Codes section.

Log Event (MQTT Component)

Fires once for each log message.

Syntax

typedef struct {
  int LogLevel;
  String Message;
  String LogType;
} TipqMQTTLogEventParams;
typedef void __fastcall (__closure *TipqMQTTLogEvent)(System::TObject* Sender, TipqMQTTLogEventParams *e);
__property TipqMQTTLogEvent OnLog = { read=FOnLog, write=FOnLog };

Remarks

This event fires once for each log message generated by the component. The verbosity is controlled by the LogLevel setting.

LogLevel indicates the level of the Message. Possible values are:

LogType identifies the type of log entry. Possible values are:

• Info: General information about the component.
• Packet: Packet content logging.
• Reconnect: Reconnection status messages.
• Session: Session status messages.

MessageAck Event (MQTT Component)

Fired when an incoming or outgoing message has completed all acknowledgment steps.

Syntax

typedef struct {
  int PacketId;
  int Direction;
  int Index;
  int ResponseCode;
} TipqMQTTMessageAckEventParams;
typedef void __fastcall (__closure *TipqMQTTMessageAckEvent)(System::TObject* Sender, TipqMQTTMessageAckEventParams *e);
__property TipqMQTTMessageAckEvent OnMessageAck = { read=FOnMessageAck, write=FOnMessageAck };

Remarks

The MessageAck event fires once an incoming or outgoing message with a QoS of 1 or 2 has successfully completed all acknowledgment steps as required by its QoS level. (Note that this event does not fire for messages with a QoS of 0 since they do not require acknowledgment.)

• PacketId: The Id of the original PUBLISH packet for the message.
• Direction: Shows whether the client (0) or the server (1) is sending the data.
• Index: The index at which the message resides in either the IncomingMessages collection or OutgoingMessages collection.
• ResponseCode: In MQTT 5, all response packets contain Reason Codes. This argument contains any code encountered in message acknowledgment packets (PUBACK, PUBREC, PUBREL, PUBCOMP).

Possible MQTT-specific values for ResponseCode are:

Inbound Message Processing

Incoming messages with a QoS of 1 follow these steps:

1. The message is added to IncomingMessages when the component receives the PUBLISH packet.
2. The component sends a PUBACK (publish acknowledgment) packet in response.
3. The MessageAck event is fired.
4. The message is removed from IncomingMessages.
5. The MessageIn event is fired.

Incoming messages with a QoS of 2 follow these steps:

1. The message is added to IncomingMessages when the component receives the PUBLISH packet.
2. The component sends a PUBREC (publish received) packet in response.
3. The component waits to receive a PUBREL (publish release) packet.
4. The component sends a PUBCOMP (publish complete) packet in response.
5. The MessageAck event is fired.
6. The message is removed from IncomingMessages.
7. The MessageIn event is fired.

Outbound Message Processing

Outgoing messages with a QoS of 1 follow these steps:

1. The component sends the PUBLISH packet, then adds the message to OutgoingMessages.
2. The component waits to receive a PUBACK (publish acknowledgment) packet.
3. The MessageAck event is fired.
4. The message is removed from OutgoingMessages.
5. The MessageOut event is fired.

Outgoing messages with a QoS of 2 follow these steps:

1. The component sends the PUBLISH packet, then adds the message to OutgoingMessages.
2. The component waits to receive a PUBREC (publish received) packet.
3. The component sends a PUBREL (publish release) packet in response.
4. The component waits to receive a PUBCOMP (publish complete) packet.
5. The MessageAck event is fired.
6. The message is removed from OutgoingMessages.
7. The MessageOut event is fired.

In MQTT 3.1.1, the RepublishInterval configuration setting, if set to a non-zero value (default), controls how long the component will wait to receive a PUBACK (for QoS 1) or PUBREC (for QoS 2) before automatically republishing an outgoing message. In MQTT 5, messages are only republished if the client is disconnected before receiving a PUBACK or PUBREC.

MessageIn Event (MQTT Component)

Fired when an incoming message has been received and/or fully acknowledged.

Syntax

typedef struct {
  int PacketId;
  String Topic;
  int QOS;
  String Message;
  DynamicArray<Byte> MessageB;
  bool Retained;
  bool Duplicate;
} TipqMQTTMessageInEventParams;
typedef void __fastcall (__closure *TipqMQTTMessageInEvent)(System::TObject* Sender, TipqMQTTMessageInEventParams *e);
__property TipqMQTTMessageInEvent OnMessageIn = { read=FOnMessageIn, write=FOnMessageIn };

Remarks

The MessageIn event fires once for each incoming message either immediately after it is received (QoS 0), or after it has been fully acknowledged (QoS 1 and 2).

• PacketId: The message packet Id. This will always be -1 if QOS is 0.
• Topic: The message's topic string.
• QOS: The message's QoS level.
• Message: The message data.
• Retained: Whether or not this message was received as a result of subscribing to a topic.
• Duplicate: Whether or not the server has indicated that this message is a duplicate of another message sent previously.

Refer to MessageAck for more information about QoS 1 and 2 message processing steps.

// MessageIn event handler. mqtt1.OnMessageIn += (s, e) => { Console.WriteLine("Received message from topic '" + e.Topic + "' with QoS " + e.QOS + ":"); Console.WriteLine(e.Message); };

MessageOut Event (MQTT Component)

Fired when an outgoing message has been sent and/or fully acknowledged.

Syntax

typedef struct {
  int PacketId;
  String Topic;
  int QOS;
  String Message;
  DynamicArray<Byte> MessageB;
  bool Retained;
  bool Duplicate;
} TipqMQTTMessageOutEventParams;
typedef void __fastcall (__closure *TipqMQTTMessageOutEvent)(System::TObject* Sender, TipqMQTTMessageOutEventParams *e);
__property TipqMQTTMessageOutEvent OnMessageOut = { read=FOnMessageOut, write=FOnMessageOut };

Remarks

The MessageOut event fires once for each outgoing message either immediately after it is sent (QoS 0), or after it has been fully acknowledged by the receiver (QoS 1 and 2).

• PacketId: The message packet Id. This will always be -1 if QOS is 0.
• Topic: The message's topic string.
• QOS: The message's QoS level.
• Message: The message data.
• Retained: Whether or not this message was sent with the "Retain" flag set.
• Duplicate: Whether or not this message was sent with the "Duplicate" flag set.

Refer to MessageAck for more information about QoS 1 and 2 message processing steps.

// MessageOut event handler. mqtt1.OnMessageOut += (s, e) => { Console.WriteLine("Send message to topic '" + e.Topic + "' with QoS " + e.QOS + ":"); Console.WriteLine(e.Message); };

ReadyToSend Event (MQTT Component)

Fired when the component is ready to send data.

Syntax

typedef struct {
} TipqMQTTReadyToSendEventParams;
typedef void __fastcall (__closure *TipqMQTTReadyToSendEvent)(System::TObject* Sender, TipqMQTTReadyToSendEventParams *e);
__property TipqMQTTReadyToSendEvent OnReadyToSend = { read=FOnReadyToSend, write=FOnReadyToSend };

Remarks

The ReadyToSend event indicates that the underlying TCP/IP subsystem is ready to accept data after a call to PublishData or PublishMessage fails due to a WOULDBLOCK condition. The event is also fired immediately after a connection to the remote host is established.

SSLServerAuthentication Event (MQTT Component)

Fired after the server presents its certificate to the client.

Syntax

typedef struct {
  String CertEncoded;
  DynamicArray<Byte> CertEncodedB;
  String CertSubject;
  String CertIssuer;
  String Status;
  bool Accept;
} TipqMQTTSSLServerAuthenticationEventParams;
typedef void __fastcall (__closure *TipqMQTTSSLServerAuthenticationEvent)(System::TObject* Sender, TipqMQTTSSLServerAuthenticationEventParams *e);
__property TipqMQTTSSLServerAuthenticationEvent OnSSLServerAuthentication = { read=FOnSSLServerAuthentication, write=FOnSSLServerAuthentication };

Remarks

During this event, the client can decide whether or not to continue with the connection process. The Accept parameter is a recommendation on whether to continue or close the connection. This is just a suggestion: application software must use its own logic to determine whether or not to continue.

When Accept is False, Status shows why the verification failed (otherwise, Status contains the string OK). If it is decided to continue, you can override and accept the certificate by setting the Accept parameter to True.

SSLStatus Event (MQTT Component)

Fired when secure connection progress messages are available.

Syntax

typedef struct {
  String Message;
} TipqMQTTSSLStatusEventParams;
typedef void __fastcall (__closure *TipqMQTTSSLStatusEvent)(System::TObject* Sender, TipqMQTTSSLStatusEventParams *e);
__property TipqMQTTSSLStatusEvent OnSSLStatus = { read=FOnSSLStatus, write=FOnSSLStatus };

Remarks

The event is fired for informational and logging purposes only. This event tracks the progress of the connection.

Subscribed Event (MQTT Component)

Fires for each topic filter subscription the server acknowledges.

Syntax

typedef struct {
  String TopicFilter;
  int QOS;
  int ResponseCode;
} TipqMQTTSubscribedEventParams;
typedef void __fastcall (__closure *TipqMQTTSubscribedEvent)(System::TObject* Sender, TipqMQTTSubscribedEventParams *e);
__property TipqMQTTSubscribedEvent OnSubscribed = { read=FOnSubscribed, write=FOnSubscribed };

Remarks

This event fires each time the server has acknowledged a topic filter subscription request (that is, calling Subscribe with multiple topic filters will cause this to fire multiple times).

• TopicFilter: The topic filter subscription request being acknowledged.
• QOS: The QoS level the server has granted for the subscription.
• ResponseCode: Indicates the result of the subscription request.

Possible values for ResponseCode are:

• 0: Success, QoS 0 granted
• 1: Success, QoS 1 granted
• 2: Success, QoS 2 granted
• 128: Unspecified error
• 131: Implementation specific error; The SUBSCRIBE is valid but the Server does not accept it.
• 135: Not authorized; The Client is not authorized to make this subscription.
• 143: Topic Filter invalid; The Topic Filter is correctly formed but is not allowed for this Client.
• 145: Packet Identifier in use
• 151: Quota exceeded; An implementation or administrative imposed limit has been exceeded.
• 158: Shared Subscriptions not supported
• 161: Shared Subscriptions not supported
• 162: Wildcard Subscriptions not supported

Keep in mind that the server may have chosen to grant a lower QoS than was requested under certain circumstances (e.g., if the server doesn't support the requested QoS).

Note: the server is not required to acknowledge a subscription before it begins delivering messages for that subscription.

Unsubscribed Event (MQTT Component)

Fires when the server has acknowledged an unsubscribe request.

Syntax

typedef struct {
  String TopicFilters;
  int ResponseCode;
} TipqMQTTUnsubscribedEventParams;
typedef void __fastcall (__closure *TipqMQTTUnsubscribedEvent)(System::TObject* Sender, TipqMQTTUnsubscribedEventParams *e);
__property TipqMQTTUnsubscribedEvent OnUnsubscribed = { read=FOnUnsubscribed, write=FOnUnsubscribed };

Remarks

This event fires when the server has acknowledged an unsubscribe request sent with Unsubscribe (that is, unlike the Subscribed event, this event fires only once for each call to Unsubscribe, regardless of how many topic filters are passed to it).

Note that in MQTT 3.1.1, servers do not specify which topic filters a client has been successfully unsubscribed in their acknowledgments. In fact, they will still acknowledge an unsubscribe request even if none of the topic filters included matched existing subscriptions. It is up to the client to keep track of what topics it is subscribed to; the TopicFilters parameter is provided as a convenience, its value simply a copy of the value passed to Unsubscribe originally.

Possible values for ResponseCode are:

• 0: Success; The subscription is deleted.
• 17: No subscription existed; No matching Topic Filter is being used by the Client.
• 128: Unspecified error; The unsubscribe could not be completed and the Server either does not wish to reveal the reason or none of the other Reason Codes apply.
• 131: Implementation specific error; The UNSUBSCRIBE is valid but the Server does not accept it.
• 135: Not authorized; The Client is not authorized to unsubscribe.
• 143: Topic Filter invalid; The Topic Filter is correctly formed but is not allowed for this Client.
• 145: Packet Identifier in use; The specified Packet Identifier is already in use.

Config Settings (MQTT Component)

MQTT Config Settings

{ 
  "ClientTopicAliasMax":"20",
  "MaximumPacketSize":"128000",
  "ReceiveMaximum":"12",
  "RequestResponseInformation":"false",
  "RequestProblemInformation":"true",
  "SessionExpInterval":"1234"
}

{
  "ContentType":"plain/text",
  "CorrelationData":"00000000",
  "MessageExpInterval":"1000",
  "PayloadFormatIndicator":"1",
  "ResponseTopic": "ResponseTopic",
  "TopicAlias":"1",
  "UserProperty":"prp1:val1",
  "UserProperty":"prp2:val2"
}

{
"ContentType":"text/plain",
"CorrelationData":"00000000",
"MessageExpInterval":"3600",
"PayloadFormatIndicator":"1",
"ResponseTopic": "ResponseTopic",
"WillDelayInterval":"10"
}

TCPClient Config Settings

SSL Config Settings

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
... Intermediate Cert ...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
... Root Cert ...
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
... Intermediate Cert ...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
... Root Cert ...
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
... Intermediate Cert...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
... Root Cert...
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

Socket Config Settings

Trappable Errors (MQTT Component)

MQTT Errors

WebSocket Errors

HTTP Errors

The component may also return one of the following error codes, which are inherited from other components.

TCPClient Errors

SSL Errors

TCP/IP Errors