Decrypt Method
Decrypts the data.
procedure Decrypt();
Remarks
Decrypt will decrypt the specified data. The following properties are applicable:
- IV (required)
- Key (required)
- UseAEAD (optional)
- AuthTag (conditional - required if UseAEAD is True)
- AdditionalAuthData (optional - applicable if UseAEAD is True);
Input and Output Properties
The component will determine the source and destination of the input and output based on which properties are set.
The order in which the input properties are checked is as follows:
When a valid source is found the search stops. The order in which the output properties are checked is as follows:
- SetOutputStream
- OutputFile
- OutputMessage: The output data is written to this property if no other destination is specified.
When using streams you may need to additionally set CloseInputStreamAfterProcessing or CloseOutputStreamAfterProcessing.
Additional Notes
The Key property must be set to the 256 bit (32 byte) value originally used to encrypt the data. IV must be set to the original IV value used to encrypt the data.
If using a password, KeyPassword must be set to the same KeyPassword used when encrypting the data. This will automatically generate both Key and IV when Decrypt is called.
InitialCounter may be set for specific cases where an initial counter of 1 is needed. The default value is 0 and is recommended.
During decryption the Progress event will fire as data is decrypted.
Decrypt Example
Chacha chacha = new Chacha();
chacha.KeyB = new byte[] { 0xBB, 0x76, 0x17, 0xC9, 0x05, 0x73, 0x4A, 0x8D, 0x59, 0x9D, 0x7B, 0x0D, 0x86, 0x2A, 0x03, 0x82, 0x50, 0x6A, 0x70, 0xFB, 0xA8, 0x56, 0x47, 0x1B, 0x1E, 0x68, 0x0B, 0x2B, 0x34, 0x18, 0x0F, 0xE2 };
chacha.IVB = new byte[] { 0x0D, 0xE4, 0x43, 0x40, 0x29, 0xAD, 0x70, 0x7D, 0x7B, 0x32, 0xB5, 0xC7 };
chacha.InputMessageB = new byte[] { 0x35, 0xBA, 0x31, 0x60, 0x02, 0x77, 0x57, 0x06, 0x5F, 0x6E, 0xE0, 0xD4, 0x76 };
chacha.Decrypt();
Console.WriteLine(chacha.OutputMessage); //outputs "hello chacha!"
AEAD Notes
When decrypting AdditionalAuthData must be set to the same value that was specified when encrypting. AuthTag must be set to the AuthTag value produced when encrypting.
Note: IncludeAuthTag may be set to True if the AuthTag value was included in the encrypted message.
Decrypt with AEAD Example
Chacha chacha = new Chacha();
chacha.KeyB = new byte[] { 0xBB, 0x76, 0x17, 0xC9, 0x05, 0x73, 0x4A, 0x8D, 0x59, 0x9D, 0x7B, 0x0D, 0x86, 0x2A, 0x03, 0x82, 0x50, 0x6A, 0x70, 0xFB, 0xA8, 0x56, 0x47, 0x1B, 0x1E, 0x68, 0x0B, 0x2B, 0x34, 0x18, 0x0F, 0xE2 };
chacha.IVB = new byte[] { 0x0D, 0xE4, 0x43, 0x40, 0x29, 0xAD, 0x70, 0x7D, 0x7B, 0x32, 0xB5, 0xC7 };
chacha.AuthTagB = new byte[] { 0x46, 0x35, 0xFD, 0x33, 0x30, 0x52, 0xAA, 0x6B, 0xBA, 0x32, 0x16, 0xA6, 0x48, 0x12, 0x52, 0x78 };
chacha.InputMessageB = new byte[] { 0x67, 0xF5, 0xC7, 0xE4, 0xE6, 0xD6, 0xC2, 0xF4, 0x09, 0xE3, 0x90, 0xF2, 0x65 };
chacha.UseAEAD = true;
chacha.AdditionalAuthData = "my auth data.";
chacha.Decrypt();
Console.WriteLine(chacha.OutputMessage); //outputs "hello chacha!"