The addr_range parameter is used when binding as a receiver or transceiver to specify a set of short message entity (SME) addresses serviced by the external SME (ESME) client. A single SME address may be specified in the address_range parameter. UNIX Regular Expression notation should be used to specify a range of addresses. Messages addressed to any destination in this range shall be routed to the ESME.

Note 1: For IP addresses, it is only possible to specify a single IP address. A range of IP addresses is not allowed. IP version 6.0 is not currently supported in this version of the protocol.

Note 2: It is likely that the addr_range field is not supported or deliberately ignored on most Message Centers (MCs). Most carriers will not allow an ESME to control the message routing because this can carry the risk of incorrectly routing messages. In such circumstances, the ESME will be requested to set the field to NULL.

By default, when the DataCoding configuration setting is used, the component will treat the message as binary. This configuration setting can be set to false to send the text user data instead.

This configuration setting will instruct the component to bind to the SMPP service as a receiver instead of a transceiver.

This configuration setting will instruct the component to bind to the SMPP service as a transmitter instead of a transceiver.

The format of the tag length value (TLV) parameter is as follows:

• One two-byte integer containing the parameter type (tag).
• One two-byte integer indicating the length of the data contained in this parameter.
• The variable-length parameter data itself.

For instance, to add a gn_lookup_userdata parameter, the type/tag is decimal 5633 (that's 0x1601 in hex), and the data in this example is "Hello World", which is 11 characters in length. So the TLV is as follows: 5633 + 11 + "Hello World", or 0x16 0x01 0x00 0x0b and then the ASCII text "Hello World". When hex-encoded, this yields the string "1601000b48656c6c6f20576f726c64". This is the value you would then use to set the CustomTLV configuration setting. You are not restricted to only one optional parameter. Multiple TLV parameters may be concatenated together.

Note: This is advanced functionality, and the class does not verify the data in this configuration setting before transmission. After the class internally decodes the string back into binary, it is passed on inside the protocol data unit (PDU) as-is without validation or modification.

This configuration setting is applicable only when using the SendMessage or SendData methods.

This configuration setting informs the message recipient about how data were encoded. The possible values are as follows:

When sending messages, this configuration setting is used to indicate the numbering plan the destination ESME. For a list of possible values, please see SourceNPI.

When sending messages, this configuration setting is used to indicate the Type of Number for the destination ESME. For a list of possible values, please see SourceTON.

This configuration setting accepts a string that will be the long message to be split into parts. The user data header (UDH) and Message Parts will be returned in hex, in the following format:

[UDH1],[MessagePart1];[UDH2],[MessagePart2];[UDH3],[MessagePart3]

When set, this configuration setting will cause the component to internally call SendMessage with the binary contents of the hex-encoded string. The return value when setting this property is the server-assigned Id of the message. Querying this property will result in an empty string.

Note: When using HexString, DataCoding must be set to 8, and the value provided to this configuration setting should be the UTF-16 hex-encoded message.

This configuration setting will request intermediate notification. By default, intermediate notification is not requested.

This configuration setting is applicable only when SplitLargeMessages is True and Protocol is set to CIMD2. The configuration setting controls the maximum size of SMS messages before they are split and has a default value of 160.

This configuration setting is applicable only when SplitLargeMessages is True. The setting controls the maximum size of SMS messages before they are split and has a default value of 140.

When sending a message, this configuration setting is used to determine whether or not an MC delivery receipt is requested. This value is 0 by default, and no receipt is requested. The possible values are as follows:

This configuration setting indicates the Id of the message being receipted in an MC delivery receipt.

Note: This is applicable only within the MessageIn event.

When sending a message, this configuration setting is used to specify the Messaging Mode in the outgoing request. For incoming messages, this value can be queried from within the MessageIn event. The possible values are as follows:

When sending a message, this configuration setting is used to specify the Message Type in the outgoing request. For incoming messages, this value can be queried from within the MessageIn event. The possible values are as follows:

Decides the format of the PDU parameter when decoding a PDU for the PITrail event. When set to Hex (1), the PDU will be encoded as a hex string. When set to Verbose (2) the PDU will be a longer hex dump.

This configuration setting allows control of the protocol identifier field value used in the outgoing messages.

This configuration indicates whether the replace_if_present_flag is enabled when sending a message. By default, this value is False, and the flag is disabled. When enabled (True), this indicates to the SMSC that the user wishes to replace a previously submitted message that is still pending delivery. If the previous message is still pending delivery, the new message will replace it. If the previous message has already been delivered or does not exist, the new message will also be delivered.

When sending a message, this configuration setting is used to determine whether or not an SME acknowledgment is requested. This value is 0 by default, and no acknowledgment is requested. The possible values are as follows:

When binding, this configuration setting is used to specify the numbering plan of the ESME. Mobiles tend to set this value to 1. Because most ESMEs are mobiles, the default value for SourceNPI is 1. The possible value are as follows:

When binding, this configuration setting is used to indicate the Type of Number for the ESME address. The possible values are as follows:

The default value is False. If set to true and the message is larger than MaxSMSLength (or MaxCIMDSMSLength), the message will automatically be split into parts when SendMessage is called.

Note: This is valid only for GSM networks.

When receiving a message that has been split, the MessageIn event provides parameters to reassemble the message.

The component can split large messages using either the UDH or segmentation and reassembly (SAR) method. The mode used is determined by this configuration setting. The possible values are as follows:

This configuration setting is applicable only when Protocol is set to smppCIMD2. This may be set to request that the server create a status report for the given conditions. The assigned value should be the sum of all desired conditions. For instance, a value of 62 means that a report should be created for all events except for a temporary error. Possible flags are as follows:

This configuration setting is useful for correct delivery of status reports when multiple instances of the same application are connected.

This configuration setting is applicable only when Protocol is set to smppCIMD2.

The default value is True, which means SendCommand will not return until a response has been received. If set to False, the class returns and does not wait for a response from the server.

The default value is True, which means SendMessage will not return until a response has been received. If set to False, the class returns the sequence number used and does not wait for a response from the server. You may then monitor the PITrail event to match the response from the server to the sent message.

When set to True (False by default), this will instruct the component to use 7-bit GSM encoding.

When set to True (True by default), the component will compress GSM 7-bit encoded characters. Some devices do not support compression. Setting this to False may allow them to be displayed.

This configuration setting applies only when UseGSM7BitEncoding is True.

This configuration setting is applicable only when Protocol is set to smppCIMD2. If set, the class will wait for a banner containing this string to be returned by the server before proceeding with the connection.

This setting determines whether the input or output stream is closed after the transfer completes. When set to True (default), all streams will be closed after a transfer is completed. In order to keep streams open after the transfer of data, set this to False. the default value is True.

When set, this configuration setting allows you to specify a different timeout value for establishing a connection. Otherwise, the class will use Timeout for establishing a connection and transmitting/receiving data.

This configuration setting is provided for use by classs that do not directly expose Firewall properties.

If a FirewallHost is given, requested connections will be authenticated through the specified firewall when connecting.

If the FirewallHost setting is set to a Domain Name, a DNS request is initiated. Upon successful termination of the request, the FirewallHost setting is set to the corresponding address. If the search is not successful, an error is returned.

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

This entry is for TCPClient only and does not work for other components that descend from TCPClient.

If this entry is set, the class acts as a server. RemoteHost and RemotePort are used to tell the SOCKS firewall in which address and port to listen to. The firewall rules may ignore RemoteHost, and it is recommended that RemoteHost be set to empty string in this case.

RemotePort is the port in which the firewall will listen to. If set to 0, the firewall will select a random port. The binding (address and port) is provided through the ConnectionStatus event.

The connection to the firewall is made by calling the Connect method.

If FirewallHost is specified, the FirewallUser and FirewallPassword settings are used to connect and authenticate to the given firewall. If the authentication fails, the class throws an exception.

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

The FirewallPort is set automatically when FirewallType is set to a valid value.

Note: This configuration setting is provided for use by classs that do not directly expose Firewall properties.

The appropriate values are as follows:

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

If the FirewallHost is specified, the FirewallUser and FirewallPassword settings are used to connect and authenticate to the Firewall. If the authentication fails, the class throws an exception.

Note: This setting is provided for use by classs that do not directly expose Firewall properties.

When set, TCPKeepAlive will automatically be set to True. A TCP keep-alive packet will be sent after a period of inactivity as defined by KeepAliveTime. If no acknowledgment is received from the remote host, the keep-alive packet will be sent again. This configuration setting specifies the interval at which the successive keep-alive packets are sent in milliseconds. This system default if this value is not specified here is 1 second.

Note: This value is not applicable in macOS.

When set, TCPKeepAlive will automatically be set to True. By default, the operating system will determine the time a connection is idle before a Transmission Control Protocol (TCP) keep-alive packet is sent. This system default if this value is not specified here is 2 hours. In many cases, a shorter interval is more useful. Set this value to the desired interval in milliseconds.

This property controls how a connection is closed. The default is True.

In the case that Linger is True (default), two scenarios determine how long the connection will linger. In the first, if LingerTime is 0 (default), the system will attempt to send pending data for a connection until the default IP timeout expires.

In the second scenario, if LingerTime is a positive value, the system will attempt to send pending data until the specified LingerTime is reached. If this attempt fails, then the system will reset the connection.

The default behavior (which is also the default mode for stream sockets) might result in a long delay in closing the connection. Although the class returns control immediately, the system could hold system resources until all pending data are sent (even after your application closes).

Setting this property to False forces an immediate disconnection. If you know that the other side has received all the data you sent (e.g., by a client acknowledgment), setting this property to False might be the appropriate course of action.

LingerTime is the time, in seconds, the socket connection will linger. This value is 0 by default, which means it will use the default IP timeout.

The LocalHost setting contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multi-homed hosts (machines with more than one IP interface) setting LocalHost to the value of an interface will make the class initiate connections (or accept in the case of server classs) only through that interface.

If the class is connected, the LocalHost setting shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multi-homed hosts (machines with more than one IP interface).

This must be set before a connection is attempted. It instructs the class to bind to a specific port (or communication endpoint) in the local machine.

Setting this to 0 (default) enables the system to choose a port at random. The chosen port will be shown by LocalPort after the connection is established.

LocalPort cannot be changed once a connection is made. Any attempt to set this when a connection is active will generate an error.

This; setting is useful when trying to connect to services that require a trusted port in the client side. An example is the remote shell (rsh) service in UNIX systems.

MaxLineLength is the size of an internal buffer, which holds received data while waiting for an EOL string.

If an EOL string is found in the input stream before MaxLineLength bytes are received, the DataIn event is fired with the EOL parameter set to True, and the buffer is reset.

If no EOL is found, and MaxLineLength bytes are accumulated in the buffer, the DataIn event is fired with the EOL parameter set to False, and the buffer is reset.

The minimum value for MaxLineLength is 256 bytes. The default value is 2048 bytes.

This configuration setting can be used to throttle outbound TCP traffic. Set this to the number of bytes to be sent per second. By default, this is not set and there is no limit.

This configuration setting optionally specifies a semicolon-separated list of hostnames or IP addresses to bypass when a proxy is in use. When requests are made to hosts specified in this property, the proxy will not be used. For instance:

www.google.com;www.nsoftware.com

If set to True, the socket's keep-alive option is enabled and keep-alive packets will be sent periodically to maintain the connection. Set KeepAliveTime and KeepAliveInterval to configure the timing of the keep-alive packets.

Note: This value is not applicable in Java.

When true, the socket will send all data that is ready to send at once. When false, the socket will send smaller buffered packets of data at small intervals. This is known as the Nagle algorithm.

By default, this config is set to false.

When set to 0 (default), the class will use IPv4 exclusively. When set to 1, the class will use IPv6 exclusively. To instruct the class to prefer IPv6 addresses, but use IPv4 if IPv6 is not supported on the system, this setting should be set to 2. The default value is 0. Possible values are:

When authenticating with NTLM, this setting specifies whether NTLM V2 is used. By default this value is False and NTLM V1 will be used. Set this to True to use NTLM V2.

When SSLProvider is set to Internal, this setting controls whether SSL packets should be logged. By default, this setting is False, as it is only useful for debugging purposes.

When enabled, SSL packet logs are output using the SSLStatus event, which will fire each time an SSL packet is sent or received.

Enabling this setting has no effect if SSLProvider is set to Platform.

If set to true, the class will reuse the context if and only if the following criteria are met:

• The target host name is the same.
• The system cache entry has not expired (default timeout is 10 hours).
• The application process that calls the function is the same.
• The logon session is the same.
• The instance of the class is the same.

This setting specifies one or more CA certificates to be included in the request when performing SSL client authentication. Some servers require the entire chain, including CA certificates, to be presented when performing SSL client authentication. The value of this setting is a newline (CrLf) separated list of certificates. For instance:

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
..
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

This setting specifies whether the class will check the Certificate Revocation List specified by the server certificate. If set to 1 or 2, the class will first obtain the list of CRL URLs from the server certificate's CRL distribution points extension. The class will then make HTTP requests to each CRL endpoint to check the validity of the server's certificate. If the certificate has been revoked or any other issues are found during validation the class throws an exception.

When set to 0 (default) the CRL check will not be performed by the class. When set to 1, it will attempt to perform the CRL check, but will continue without an error if the server's certificate does not support CRL. When set to 2, it will perform the CRL check and will throw an error if CRL is not supported.

This configuration setting is only supported in the Java, C#, and C++ editions. In the C++ edition, it is only supported on Windows operating systems.

This setting specifies whether the class will use OCSP to check the validity of the server certificate. If set to 1 or 2, the class will first obtain the OCSP URL from the server certificate's OCSP extension. The class will then locate the issuing certificate and make an HTTP request to the OCSP endpoint to check the validity of the server's certificate. If the certificate has been revoked or any other issues are found during validation the class throws an exception.

When set to 0 (default) the class will not perform an OCSP check. When set to 1, it will attempt to perform the OCSP check, but will continue without an error if the server's certificate does not support OCSP. When set to 2, it will perform the OCSP check and will throw an error if OCSP is not supported.

This configuration setting is only supported in the Java, C#, and C++ editions. In the C++ edition, it is only supported on Windows operating systems.

This minimum cipher strength largely dependent on the security modules installed on the system. If the cipher strength specified is not supported, an error will be returned when connections are initiated.

Please note that this setting contains the minimum cipher strength requested from the security library. The actual cipher strength used for the connection is shown by the SSLStatus event.

Use this setting with caution. Requesting a lower cipher strength than necessary could potentially cause serious security vulnerabilities in your application.

When the provider is OpenSSL, SSLCipherStrength is currently not supported. This functionality is instead made available through the OpenSSLCipherList config setting.

Possible values are SSL, SSLv2, SSLv3, TLS and TLSv1. Use it only in case your security provider does not support TLS. This is the parameter "protocol" inside the SSLContext.getInstance(protocol) call.

The enabled cipher suites to be used in SSL negotiation.

By default, the enabled cipher suites will include all available ciphers ("*").

The special value "*" means that the class will pick all of the supported cipher suites. If SSLEnabledCipherSuites is set to any other value, only the specified cipher suites will be considered.

Multiple cipher suites are separated by semicolons.

Note: This value must be set after SSLProvider is set.

Example values: obj.config("SSLEnabledCipherSuites=*"); obj.config("SSLEnabledCipherSuites=SSL_RSA_WITH_RC4_128_SHA"); obj.config("SSLEnabledCipherSuites=SSL_RSA_WITH_RC4_128_SHA; SSL_DHE_RSA_WITH_3DES_EDE_CBC_SHA"); Possible values when SSLProvider is set to latform include:

• SSL_DHE_RSA_EXPORT_WITH_DES40_CBC_SHA
• SSL_DHE_RSA_WITH_3DES_EDE_CBC_SHA
• SSL_RSA_WITH_RC4_128_SHA
• SSL_RSA_WITH_DES_CBC_SHA
• SSL_RSA_EXPORT_WITH_DES40_CBC_SHA
• SSL_DH_anon_WITH_DES_CBC_SHA
• SSL_RSA_EXPORT_WITH_RC4_40_MD5
• SSL_DHE_DSS_EXPORT_WITH_DES40_CBC_SHA
• SSL_DH_anon_EXPORT_WITH_RC4_40_MD5
• SSL_DHE_DSS_WITH_DES_CBC_SHA
• SSL_RSA_WITH_NULL_MD5
• SSL_DH_anon_WITH_3DES_EDE_CBC_SHA
• SSL_DHE_RSA_WITH_DES_CBC_SHA
• SSL_DH_anon_EXPORT_WITH_DES40_CBC_SHA
• SSL_RSA_WITH_NULL_SHA
• SSL_DH_anon_WITH_RC4_128_MD5
• SSL_RSA_WITH_RC4_128_MD5
• SSL_DHE_DSS_WITH_3DES_EDE_CBC_SHA
• SSL_RSA_WITH_3DES_EDE_CBC_SHA
• TLS_ECDH_ECDSA_WITH_NULL_SHA
• TLS_DH_anon_WITH_AES_128_CBC_SHA256 (Not Recommended)
• TLS_ECDH_anon_WITH_RC4_128_SHA
• TLS_DH_anon_WITH_AES_128_CBC_SHA (Not Recommended)
• TLS_DHE_RSA_WITH_AES_128_CBC_SHA
• TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA
• TLS_KRB5_WITH_3DES_EDE_CBC_SHA
• TLS_DHE_DSS_WITH_AES_128_CBC_SHA256
• TLS_ECDH_ECDSA_WITH_3DES_EDE_CBC_SHA
• TLS_DHE_RSA_WITH_AES_128_CBC_SHA256
• TLS_KRB5_EXPORT_WITH_RC4_40_SHA
• TLS_ECDH_RSA_WITH_AES_128_CBC_SHA256
• TLS_ECDHE_RSA_WITH_RC4_128_SHA
• TLS_ECDH_ECDSA_WITH_RC4_128_SHA
• TLS_ECDH_anon_WITH_NULL_SHA
• TLS_ECDHE_ECDSA_WITH_RC4_128_SHA
• TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
• TLS_RSA_WITH_NULL_SHA256
• TLS_ECDH_anon_WITH_3DES_EDE_CBC_SHA
• TLS_KRB5_WITH_RC4_128_MD5
• TLS_ECDHE_ECDSA_WITH_NULL_SHA
• TLS_ECDHE_ECDSA_WITH_3DES_EDE_CBC_SHA
• TLS_ECDH_RSA_WITH_RC4_128_SHA
• TLS_EMPTY_RENEGOTIATION_INFO_SCSV
• TLS_KRB5_WITH_3DES_EDE_CBC_MD5
• TLS_KRB5_WITH_RC4_128_SHA
• TLS_ECDH_RSA_WITH_3DES_EDE_CBC_SHA
• TLS_ECDH_RSA_WITH_NULL_SHA
• TLS_ECDH_RSA_WITH_AES_128_CBC_SHA
• TLS_KRB5_WITH_DES_CBC_MD5
• TLS_KRB5_EXPORT_WITH_RC4_40_MD5
• TLS_KRB5_EXPORT_WITH_DES_CBC_40_MD5
• TLS_ECDH_anon_WITH_AES_128_CBC_SHA
• TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA
• TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA256
• TLS_KRB5_WITH_DES_CBC_SHA
• TLS_RSA_WITH_AES_128_CBC_SHA
• TLS_KRB5_EXPORT_WITH_DES_CBC_40_SHA
• TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA256
• TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA256
• TLS_ECDHE_RSA_WITH_NULL_SHA
• TLS_RSA_WITH_AES_128_CBC_SHA256
• TLS_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA
• TLS_DHE_DSS_WITH_AES_128_CBC_SHA

Possible values when SSLProvider is set to Internal include:

• TLS_ECDHE_ECDSA_WITH_AES_256_GCM_SHA384
• TLS_ECDHE_ECDSA_WITH_AES_128_GCM_SHA256
• TLS_ECDHE_RSA_WITH_AES_128_GCM_SHA256
• TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384
• TLS_ECDH_ECDSA_WITH_AES_256_GCM_SHA384
• TLS_RSA_WITH_AES_256_GCM_SHA384
• TLS_RSA_WITH_AES_128_GCM_SHA256
• TLS_ECDH_ECDSA_WITH_AES_128_GCM_SHA256
• TLS_DHE_DSS_WITH_AES_256_GCM_SHA384
• TLS_DHE_RSA_WITH_AES_256_GCM_SHA384
• TLS_ECDH_RSA_WITH_AES_256_GCM_SHA384
• TLS_ECDH_RSA_WITH_AES_128_GCM_SHA256
• TLS_DHE_RSA_WITH_AES_128_GCM_SHA256
• TLS_DHE_DSS_WITH_AES_128_GCM_SHA256
• TLS_DH_RSA_WITH_AES_128_GCM_SHA256 (Not Recommended)
• TLS_DH_RSA_WITH_AES_256_GCM_SHA384 (Not Recommended)
• TLS_DH_DSS_WITH_AES_128_GCM_SHA256 (Not Recommended)
• TLS_DH_DSS_WITH_AES_256_GCM_SHA384 (Not Recommended)
• TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA384
• TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA256
• TLS_ECDH_ECDSA_WITH_AES_256_CBC_SHA384
• TLS_DHE_DSS_WITH_AES_256_CBC_SHA256
• TLS_RSA_WITH_AES_256_CBC_SHA256
• TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA384
• TLS_ECDH_RSA_WITH_AES_256_CBC_SHA384
• TLS_DHE_RSA_WITH_AES_256_CBC_SHA256
• TLS_DHE_RSA_WITH_AES_128_CBC_SHA256
• TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA256
• TLS_RSA_WITH_AES_128_CBC_SHA256
• TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA256
• TLS_ECDH_RSA_WITH_AES_128_CBC_SHA256
• TLS_DHE_DSS_WITH_AES_128_CBC_SHA256
• TLS_RSA_WITH_AES_256_CBC_SHA
• TLS_ECDHE_ECDSA_WITH_AES_256_CBC_SHA
• TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA
• TLS_ECDH_ECDSA_WITH_AES_256_CBC_SHA
• TLS_DHE_RSA_WITH_AES_256_CBC_SHA
• TLS_ECDH_RSA_WITH_AES_256_CBC_SHA
• TLS_DHE_DSS_WITH_AES_256_CBC_SHA
• TLS_RSA_WITH_AES_128_CBC_SHA
• TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
• TLS_ECDHE_ECDSA_WITH_AES_128_CBC_SHA
• TLS_ECDH_ECDSA_WITH_AES_128_CBC_SHA
• TLS_ECDH_RSA_WITH_AES_128_CBC_SHA
• TLS_DHE_RSA_WITH_AES_128_CBC_SHA
• TLS_DHE_DSS_WITH_AES_128_CBC_SHA
• TLS_ECDHE_ECDSA_WITH_3DES_EDE_CBC_SHA
• TLS_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA
• TLS_ECDH_ECDSA_WITH_3DES_EDE_CBC_SHA
• TLS_ECDH_RSA_WITH_3DES_EDE_CBC_SHA
• TLS_DHE_RSA_WITH_3DES_EDE_CBC_SHA
• TLS_DHE_DSS_WITH_3DES_EDE_CBC_SHA
• TLS_RSA_WITH_3DES_EDE_CBC_SHA
• TLS_RSA_WITH_DES_CBC_SHA
• TLS_DHE_RSA_WITH_DES_CBC_SHA
• TLS_DHE_DSS_WITH_DES_CBC_SHA
• TLS_RSA_WITH_RC4_128_MD5
• TLS_RSA_WITH_RC4_128_SHA

When TLS 1.3 is negotiated (see SSLEnabledProtocols) only the following cipher suites are supported:

• TLS_AES_256_GCM_SHA384
• TLS_CHACHA20_POLY1305_SHA256
• TLS_AES_128_GCM_SHA256

SSLEnabledCipherSuites is used together with SSLCipherStrength.

Used to enable/disable the supported security protocols.

Not all supported protocols are enabled by default (the value of this setting is 4032). If you want more granular control over the enabled protocols, you can set this property to the binary 'OR' of one or more of the following values:

SSLEnabledProtocols - TLS 1.3 Notes

By default when TLS 1.3 is enabled the class will use the internal TLS implementation when the SSLProvider is set to Automatic for all editions.

In editions which are designed to run on Windows SSLProvider can be set to Platform to use the platform implementation instead of the internal implementation. When configured in this manner, please note that the platform provider is only supported on Windows 11 / Windows Server 2022 and up. The default internal provider is available on all platforms and is not restricted to any specific OS version.

If set to 1 (Platform provider) please be aware of the following notes:

• The platform provider is only available on Windows 11 / Windows Server 2022 and up.
• SSLEnabledCipherSuites and other similar SSL configuration settings are not supported.
• If SSLEnabledProtocols includes both TLS 1.3 and TLS 1.2 the above restrictions are still applicable even if TLS 1.2 is negotiated. Enabling TLS 1.3 with the platform provider changes the implementation used for all TLS versions.

SSLEnabledProtocols: SSL2 and SSL3 Notes:

SSL 2.0 and 3.0 are not supported by the class when the SSLProvider is set to internal. To use SSL 2.0 or SSL 3.0, the platform security API must have the protocols enabled and SSLProvider needs to be set to platform.

This setting specifies whether the renegotiation_info SSL extension will be used in the request when using the internal security API. This setting is true by default, but can be set to false to disable the extension.

This setting is only applicable when SSLProvider is set to Internal.

This setting specifies whether the Encoded parameter of the SSLServerAuthentication event contains the full certificate chain. By default this value is False and only the leaf certificate will be present in the Encoded parameter of the SSLServerAuthentication event.

If set to True all certificates returned by the server will be present in the Encoded parameter of the SSLServerAuthentication event. This includes the leaf certificate, any intermediate certificate, and the root certificate.

Note: When SSLProvider is set to Internal this value is automatically set to true. This is needed for proper validation when using the internal provider.

This setting optionally specifies the full path to a file on disk where per-session secrets are stored for debugging purposes.

When set, the class will save the session secrets in the same format as the SSLKEYLOGFILE environment variable functionality used by most major browsers and tools such as Chrome, Firefox, and cURL. This file can then be used in tools such as Wireshark to decrypt TLS traffice for debugging purposes. When writing to this file the class will only append, it will not overwrite previous values.

Note: This setting is only applicable when SSLProvider is set to Internal.

Returns the cipher suite negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipher[connId]");

Returns the strength of the cipher suite negotiated during the SSL handshake.

Note: For server components (e.g.TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipherStrength[connId]");

Returns the cipher suite negotiated during the SSL handshake represented as a single string.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedCipherSuite[connId]");

Returns the key exchange algorithm negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedKeyExchange[connId]");

Returns the strenghth of the key exchange algorithm negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedKeyExchangeStrength[connId]");

Returns the protocol version negotiated during the SSL handshake.

Note: For server components (e.g. TCPServer) this is a per-connection setting accessed by passing the ConnectionId. For example: server.Config("SSLNegotiatedVersion[connId]");

This setting optionally specifies one or more CA certificates to be used when verifying the server certificate. When verifying the server's certificate the certificates trusted by the system will be used as part of the verification process. If the server's CA certificates are not installed to the trusted system store, they may be specified here so they are included when performing the verification process. This setting should only be set if the server's CA certificates are not already trusted on the system and cannot be installed to the trusted system store.

The value of this setting is a newline (CrLf) separated list of certificates. For instance:

-----BEGIN CERTIFICATE-----
MIIEKzCCAxOgAwIBAgIRANTET4LIkxdH6P+CFIiHvTowDQYJKoZIhvcNAQELBQAw
...
eWHV5OW1K53o/atv59sOiW5K3crjFhsBOd5Q+cJJnU+SWinPKtANXMht+EDvYY2w
F0I1XhM+pKj7FjDr+XNj
-----END CERTIFICATE-----
\r \n
-----BEGIN CERTIFICATE-----
MIIEFjCCAv6gAwIBAgIQetu1SMxpnENAnnOz1P+PtTANBgkqhkiG9w0BAQUFADBp
..
d8q23djXZbVYiIfE9ebr4g3152BlVCHZ2GyPdjhIuLeH21VbT/dyEHHA
-----END CERTIFICATE-----

Possible values include SunX509. This is the parameter "algorithm" inside the TrustManagerFactory.getInstance(algorithm) call.

This setting specifies the allowed server certificate signature algorithms when SSLProvider is set to Internal and SSLEnabledProtocols is set to allow TLS 1.2.

When specified the class will verify that the server certificate signature algorithm is among the values specified in this setting. If the server certificate signature algorithm is unsupported the class throws an exception.

The format of this value is a comma separated list of hash-signature combinations. For instance: component.SSLProvider = TCPClientSSLProviders.sslpInternal; component.Config("SSLEnabledProtocols=3072"); //TLS 1.2 component.Config("TLS12SignatureAlgorithms=sha256-rsa,sha256-dsa,sha1-rsa,sha1-dsa"); The default value for this setting is sha512-ecdsa,sha512-rsa,sha512-dsa,sha384-ecdsa,sha384-rsa,sha384-dsa,sha256-ecdsa,sha256-rsa,sha256-dsa,sha224-ecdsa,sha224-rsa,sha224-dsa,sha1-ecdsa,sha1-rsa,sha1-dsa.

In order to not restrict the server's certificate signature algorithm, specify an empty string as the value for this setting, which will cause the signature_algorithms TLS 1.2 extension to not be sent.

This setting specifies a comma separated list of named groups used in TLS 1.2 for ECC.

The default value is ecdhe_secp256r1,ecdhe_secp384r1,ecdhe_secp521r1.

When using TLS 1.2 and SSLProvider is set to Internal, the values refer to the supported groups for ECC. The following values are supported:

• "ecdhe_secp256r1" (default)
• "ecdhe_secp384r1" (default)
• "ecdhe_secp521r1" (default)

This setting specifies a comma separated list of named groups used in TLS 1.3 for key exchange. The groups specified here will have key share data pregenerated locally before establishing a connection. This can prevent an additional round trip during the handshake if the group is supported by the server.

The default value is set to balance common supported groups and the computational resources required to generate key shares. As a result only some groups are included by default in this setting.

Note: All supported groups can always be used during the handshake even if not listed here, but if a group is used which is not present in this list it will incur an additional round trip and time to generate the key share for that group.

In most cases this setting does not need to be modified. This should only be modified if there is a specific reason to do so.

The default value is ecdhe_x25519,ecdhe_secp256r1,ecdhe_secp384r1,ffdhe_2048,ffdhe_3072

The values are ordered from most preferred to least preferred. The following values are supported:

• "ecdhe_x25519" (default)
• "ecdhe_x448"
• "ecdhe_secp256r1" (default)
• "ecdhe_secp384r1" (default)
• "ecdhe_secp521r1"
• "ffdhe_2048" (default)
• "ffdhe_3072" (default)
• "ffdhe_4096"
• "ffdhe_6144"
• "ffdhe_8192"

This setting holds a comma separated list of allowed signature algorithms. Possible values are:

• "ed25519" (default)
• "ed448" (default)
• "ecdsa_secp256r1_sha256" (default)
• "ecdsa_secp384r1_sha384" (default)
• "ecdsa_secp521r1_sha512" (default)
• "rsa_pkcs1_sha256" (default)
• "rsa_pkcs1_sha384" (default)
• "rsa_pkcs1_sha512" (default)
• "rsa_pss_sha256" (default)
• "rsa_pss_sha384" (default)
• "rsa_pss_sha512" (default)

This setting specifies a comma separated list of named groups used in TLS 1.3 for key exchange. This setting should only be modified if there is a specific reason to do so.

The default value is ecdhe_x25519,ecdhe_x448,ecdhe_secp256r1,ecdhe_secp384r1,ecdhe_secp521r1,ffdhe_2048,ffdhe_3072,ffdhe_4096,ffdhe_6144,ffdhe_8192

The values are ordered from most preferred to least preferred. The following values are supported:

• "ecdhe_x25519" (default)
• "ecdhe_x448" (default)
• "ecdhe_secp256r1" (default)
• "ecdhe_secp384r1" (default)
• "ecdhe_secp521r1" (default)
• "ffdhe_2048" (default)
• "ffdhe_3072" (default)
• "ffdhe_4096" (default)
• "ffdhe_6144" (default)
• "ffdhe_8192" (default)

If AbsoluteTimeout is set to True, any method which does not complete within Timeout seconds will be aborted. By default, AbsoluteTimeout is False, and the timeout is an inactivity timeout.

Note: This option is not valid for UDP ports.

When the firewall is a tunneling proxy, use this property to send custom (additional) headers to the firewall (e.g. headers for custom authentication schemes).

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be receiving. Increasing the value of the InBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the class is activated the InBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be sending. Increasing the value of the OutBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the class is activated the OutBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

When queried, this setting will return a string containing information about the product's build.

In a GUI-based application, long-running blocking operations may cause the application to stop responding to input until the operation returns. The class will attempt to discover whether or not the application has a message loop and, if one is discovered, it will process events in that message loop during any such blocking operation.

In some non-GUI applications, an invalid message loop may be discovered that will result in errant behavior. In these cases, setting GUIAvailable to false will ensure that the class does not attempt to process external events.

When queried, this setting will return a string containing information about the license this instance of a class is using. It will return the following information:

• Product: The product the license is for.
• Product Key: The key the license was generated from.
• License Source: Where the license was found (e.g., RuntimeLicense, License File).
• License Type: The type of license installed (e.g., Royalty Free, Single Server).
• Last Valid Build: The last valid build number for which the license will work.

In certain circumstances it may be beneficial to mask sensitive data, like passwords, in log messages. Set this to true to mask sensitive data. The default is true.

This setting only works on these classes: AS3Receiver, AS3Sender, Atom, Client(3DS), FTP, FTPServer, IMAP, OFTPClient, SSHClient, SCP, Server(3DS), Sexec, SFTP, SFTPServer, SSHServer, TCPClient, TCPServer.

If set to True (default), when the class creates a thread, the thread's Daemon property will be explicitly set to True. When set to False, the class will not set the Daemon property on the created thread. The default value is True.

When set to false, the class will use the system security libraries by default to perform cryptographic functions where applicable.

Setting this configuration setting to true tells the class to use the internal implementation instead of using the system security libraries.

This setting is set to false by default on all platforms.