Set this to the number of bytes the block should be. This uses the blocksize option as defined in RFC 2348. The default is 512.

Available modes:

If this is set to true, the component will capture the IP packet information.

The default value for this setting is False.

Note: This setting is only available in Windows.

This setting specifies whether a hostname is resolved immediately when RemoteHost is set. If true the cmdlet will resolve the hostname and the IP address will be present in the RemoteHost property. If false, the hostname is not resolved until needed by the component when a method to connect or send data is called. If desired, ResolveRemoteHost may called to manually resolve the value in RemoteHost at any time.

The default value is false for the default library and true for the Async library. The default value is false.

If CaptureIPPacketInfo is set to true, then this will be populated with the packet's destination address when a packet is received. This information will be accessible in the DataIn event.

Note: This setting is only available in Windows.

When set to True, packets sent by the cmdlet will have the Don't Fragment flag set. The default value is False.

The LocalHost setting contains the name of the local host as obtained by the gethostname() system call, or if the user has assigned an IP address, the value of that address.

In multi-homed hosts (machines with more than one IP interface) setting LocalHost to the value of an interface will make the cmdlet initiate connections (or accept in the case of server cmdlets) only through that interface.

If the cmdlet is connected, the LocalHost setting shows the IP address of the interface through which the connection is made in internet dotted format (aaa.bbb.ccc.ddd). In most cases, this is the address of the local host, except for multi-homed hosts (machines with more than one IP interface).

This must be set before a connection is attempted. It instructs the cmdlet to bind to a specific port (or communication endpoint) in the local machine.

Setting this to 0 (default) enables the system to choose a port at random. The chosen port will be shown by LocalPort after the connection is established.

LocalPort cannot be changed once a connection is made. Any attempt to set this when a connection is active will generate an error.

This; setting is useful when trying to connect to services that require a trusted port in the client side. An example is the remote shell (rsh) service in UNIX systems.

This setting specifies the maximum size of the datagrams that the cmdlet will accept without truncation.

UseConnection must be True to use this setting. This option allows you to specify an arbitrary DSCP value between 0 and 63. The default is 0. When set to the default value the component will not set a DSCP value.

Note: This setting uses the qWAVE API is only available on Windows 7, Windows Server 2008 R2, and later.

UseConnection must be True to use this setting. You may specify either the text or integer values: BestEffort (0), Background (1), ExcellentEffort (2), AudioVideo (3), Voice (4), and Control (5).

Note: This setting uses the qWAVE API which is only available on Windows Vista and Windows Server 2008 or above.

Note: QOSTrafficType must be set before setting Active to true.

This option must be set before the cmdlet is activated through the Active property or it will have no effect.

The default value for this setting is False.

UseConnection specifies whether the cmdlet should use a connected socket or not. The connection is defined as an association in between the local address/port and the remote address/port. As such, this is not a connection in the traditional TCP sense. What it means is only that the cmdlet will send and receive data only to and from the specified destination.

The default value for this setting is False.

By default, the component expects an IPv4 address for local and remote host properties, and will create an IPv4 socket. To use IPv6 instead, set this to True.

If AbsoluteTimeout is set to True, any method which does not complete within Timeout seconds will be aborted. By default, AbsoluteTimeout is False, and the timeout is an inactivity timeout.

Note: This option is not valid for UDP ports.

When the firewall is a tunneling proxy, use this property to send custom (additional) headers to the firewall (e.g. headers for custom authentication schemes).

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be receiving. Increasing the value of the InBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the cmdlet is activated the InBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

This is the size of an internal queue in the TCP/IP stack. You can increase or decrease its size depending on the amount of data that you will be sending. Increasing the value of the OutBufferSize setting can provide significant improvements in performance in some cases.

Some TCP/IP implementations do not support variable buffer sizes. If that is the case, when the cmdlet is activated the OutBufferSize reverts to its defined size. The same happens if you attempt to make it too large or too small.

When queried, this setting will return a string containing information about the product's build.

The default code page is Unicode UTF-8 (65001).

The following is a list of valid code page identifiers:

When queried, this setting will return a string containing information about the license this instance of a cmdlet is using. It will return the following information:

• Product: The product the license is for.
• Product Key: The key the license was generated from.
• License Source: Where the license was found (e.g., RuntimeLicense, License File).
• License Type: The type of license installed (e.g., Royalty Free, Single Server).
• Last Valid Build: The last valid build number for which the license will work.

In certain circumstances it may be beneficial to mask sensitive data, like passwords, in log messages. Set this to true to mask sensitive data. The default is true.

This setting only works on these cmdlets: AS3Receiver, AS3Sender, Atom, Client(3DS), FTP, FTPServer, IMAP, OFTPClient, SSHClient, SCP, Server(3DS), Sexec, SFTP, SFTPServer, SSHServer, TCPClient, TCPServer.

When set to false, the cmdlet will use the system security libraries by default to perform cryptographic functions where applicable. In this case, calls to unmanaged code will be made. In certain environments, this is not desirable. To use a completely managed security implementation, set this setting to true.

Setting this configuration setting to true tells the cmdlet to use the internal implementation instead of using the system security libraries.

On Windows, this setting is set to false by default. On Linux/macOS, this setting is set to true by default.

If using the .NET Standard Library, this setting will be true on all platforms. The .NET Standard library does not support using the system security libraries.

Note: This setting is static. The value set is applicable to all cmdlets used in the application.

When this value is set, the product's system dynamic link library (DLL) is no longer required as a reference, as all unmanaged code is stored in that file.